Partyline User Guide PN: 399G052 Rev: D 04/17/14
Document Reference Clear-Com HelixNet Partyline User Guide Part Number: 399G052 Revision: D Legal Disclaimers Copyright © 2014 HME Clear-Com Ltd. All rights reserved. Clear-Com, the Clear-Com logo, Clear-Com Concert and HelixNet are registered trademarks of HM Electronics, Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of the agreement.
Contents 3 Contents 3 1 Introduction....................................................................................................6 1.1 Important Safety instructions ...........................................................................6 1.2 Further information ..........................................................................................7 2 Panels and Interfaces ....................................................................................8 2.
5.6 Administration ................................................................................................78 5.7 Diagnostics ....................................................................................................80 6 Configuring and managing the Speaker Station .......................................82 6.1 Using the Menus ............................................................................................82 6.2 Configuring the Audio settings ........................
11.1 Using the beltpack keysets ..........................................................................113 11.2 Entering and exiting Menu mode .................................................................114 11.3 Adjusting the Program Feed volume level. ...................................................114 12 Using the Speaker Station ........................................................................115 12.1 Using the gooseneck mic, loudspeaker and headset .........................
1 Introduction This guide is intended to help you install, configure, and use the HelixNet Partyline™ system. HelixNet Partyline is a digital intercom system, featuring the award-winning I.V Core Technology from Clear-Com®. The system is designed to be as simple to use and configure as a two-wire intercom / analog Partyline system, while exploiting the flexibility and network management capabilities of a matrix system.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualified service personnel.
2 Panels and Interfaces 2.
Key to Main Station/Remote Station: Front panel Feature Description A Ear for rack mounting Main Station/Remote Station. B Headset socket (4-pin XLR–M) Pin Function 1 Mic ground 2 Mic + 3 Earphone ground 4 Earphone Table 2-1: Headset socket pin out C Gooseneck microphone socket (3-pin female Tuchel connector) D Mic control [ MIC ON]. Press to activate mic audio. E Headset key [ HSET]. Press to activate the headset mic.
Key to Main Station/Remote Station: Front panel Feature I Description Master Station LEDs for lines 1 and 2 (partylines). The LEDs indicate the status of the intercom circuit powering. When an LED is lit: • Green, the line is functioning. • Amber, the line is busy. • Red, there is an error or fault on the line. Remote Station LEDs for line status and LAN status. The LEDs indicate the status of the intercom circuit powering. When an LED is lit: Green, the line is functioning. Amber, the line is busy.
Key to Main Station/Remote Station: Front panel Feature Description N All Talk. Press to talk to all channels (intercom devices and systems) connected to the main station. O USB 2.0 (Micro-AB) connector. For software upgrades (see 4.7.2 Updating the software and 4.7.6 Saving and restoring the software settings.). Note: P This connector is not present on the Remote Station. USB 2.0 (Standard-A) connector. For software upgrades (see 4.7.2 Updating the software and 4.7.
2.1.1 Main Station/Remote channel keyset and display Figure 2-2: Main Station/Remote Station (Front panel): Keyset Key to Main Station/Remote Station front panel: Channel keyset Feature Description A Display screen. In Menu mode, the display screens display the four levels of menu. The menu hierarchy proceeds left to right: • The top level menu is presented in the first screen (furthest left on the front panel).
Main Station/Remote Station display icons and indicators Name Icon Description Channel label A descriptive name for the channel. The maximum length is 10 characters. Channel listen volume level The volume of the channel audio. Link Appears on the Main Station when linking is enabled. Broken link Appears on the Main Station when a connection to a another Main Station is lost. Pair Appears on the Remote Station and Speaker Station when it is connected properly over Ethernet.
2.
Key to Main Station: rear panel Feature Description A Power supply with metal cable clip. The power supply operates at 100 - 240 VAC / 50-60Hz / 250 watts / T 3.15A H 250 V. B Control I/O (25 way female D-type). Use to connect up to 4 relay control outputs and 4 optically isolated control inputs (see 4.5 Configuring the Control I/O).
D SA [Stage Announce] line out (3-pin male XLR). Pin Function Pin 1 Ground Pin 2 Positive Pin 3 Negative Table 2-8: SA pin out E Program Input (3-pin female XLR). Pin Function Pin 1 Ground Pin 2 Positive Pin 3 Negative Table 2-9: Program input pin out F Line 1 (partyline). (3-pin male and female XLR connectors). Pin Function Pin 1 Ground Pin 2 +30V DC and Audio Pin 3 -30V DC and Audio Table 2-10: Line 1 pin out G Line 2 (partyline). (3-pin male and female XLR connectors).
Note: 2.2.1 The HMS-4X Main Station does not have a power switch, button or key. The system powers up when you connect the power supply. HMS-4X Main Station rear panel: Interface modules Up to three Interface modules (of the same or different types) can be fitted to the extension bay of the main station. When looking at the rear of the Main Station, expansion slot 1 is the left-hand slot, expansion slot 2 is the middle slot, and expansion slot 3 is the right-hand slot.
Interface module Description Four-wire interface module (HLI-4W2) This is a two channel device that enables interoperability with the Eclipse® digital matrix system and other four-wire audio sources such as telephone hybrids, AB-120/-100, PA (Public Address) / SA (Stage Announce) systems. The module also enables HelixNet-to-HelixNet connections using four-wire audio ports.
Interface module Description Fiber interface module (HLI-FBS) Enables linking of Main Stations, and connection of Remote Stations and Speaker Stations via a fiber link. Contains two SFP cage slots. The module is supplied with one transceiver fitted. Any 100BASE-X SFP can be connected. Warning: Both ports are configured to bridge traffic from one port to the other in order to work in a daisychained configuration.
2.
Key to Remote Station: rear panel Feature Description A PSU holder for a separate external AC-DC power supply. The external PSU provides the 48V required and at its input takes 100-240V, 50-60Hz. B Power supply. The power input connector is a low voltage DC connection. It is 48VDC at a max power of 12.95W. C Line 1 (partyline). (3-pin male and female XLR connectors).
Key to Remote Station: rear panel Feature G Description Program Input (3-pin m XLR). Pin Function Pin 1 Ground Pin 2 Positive Pin 3 Negative Table 2-20 Program input pinout H Hot Mic output. This connection is a 1/4-in (0.64 cm) phone jack. It provides an output signal from the selected headset or panel microphone. The Hot Mic output is always live. Audio from the mic is routed through the Hot Mic output even if the mic is inactive (off).
2.
Key to Speaker Station front panel Description Feature Tilt adjustable display screen. The following default information is displayed: A • The channel label. • The channel listen (volume) level. For a full description of the display screen information, see Table 2-5 MainStation/Remote Station display icons and indicators. In Menu mode, the display screens display the four levels of menu.
2.4.1 Speaker Station front panel function buttons A B D C Figure 2-6 Speaker Station keyset Key to Speaker Station front panel function buttons Feature Description A Mic control [ MIC ON]. Press to activate mic audio. B Shift key. Press to display two alternative channels on the Speaker Station displays. C Menu. Press to display the Speaker Station menus in the display screens. Use the rotary control for each display screen to scroll and select menu items. D Headset key [ HSET].
2.4.
2.4.
Key to S-Mount rear panel keyset Feature Description A Ethernet/Power over Ethernet connection (RJ45) B Power connection. C Line 1 Party Line in. (3-pin male XLR connector). Pin Function Pin 1 Ground Pin 2 +30V DC and Audio Pin 3 -30V DC and Audio Table 2-26 Line 1 pinout D Line 2 Party Line out.(3-pin female XLR connector).
2.5 HBP-2X Beltpack 2.5.
Key to HBP-2X user controls (front and side view) Feature Description E A Menu key. Press firmly to enter Menu mode (see also D ). To exit Menu mode, press the Menu key again. The display screen times out of Menu mode and displays the channel label(s) if no key is pressed for 20 seconds. B USB 2.0 (Micro-AB) connector. For software upgrades. C Casing. Metal casing for robust use. For information about the beltclip, beltloops, and feet, see 2.5.3 HBP-2X beltclip, beltloops and feet (base view).
2.5.2 HBP-2X connectors and controls (rear view) E A B C D Figure 2-8: HBP-2X connectors and controls (rear view) Key to HBP-2X Beltpack (Rear view) Feature A Description Line (Partyline) (3-pin female XLR connector). Pin Function 1 Ground 2 +30V DC and Audio 3 -30V DC and Audio Table 2-30: Line (female) pin out B Line (Partyline) (3-pin male XLR connector). Pass-through for daisy chain connection (see Figure 3-2: Example system topologies (layouts)).
Key to HBP-2X Beltpack (Rear view) Feature E Description Headset connector (4-pin male or 5-pin female XLR connector).
2.5.3 HBP-2X beltclip, beltloops and feet (base view) Figure 2-9: HBP-2X Beltpack: base view Key to HBP-2X Beltpack (Base view) Feature Description A Beltclip. The beltclip is secured to the unit with three screws, and may be removed, according to your requirements. B Feet (positions only). The beltpack can also be placed on a level surface (once the beltclip has been removed). To give the beltpack more grip on the surface, attach the four rubber feet supplied with the beltpack.
3 Installing HelixNet Partyline This chapter describes how to install your HelixNet Partyline system. It also provides basic guidance on planning your installation. Tip: For guidance on connecting HelixNet Partyline to other systems, using the optional interface modules, see 13 Connecting to Other Intercom Systems. Do not plug any non-approved equipment into HelixNet Partyline. HelixNet Partyline operates at different voltage levels than analog two-wire partyline systems.
3.1 Planning your HelixNet Partyline installation 3.1.
Key to analog and digital cabling comparison diagram Feature A B P1 Description Example 4-channel analog main station (MS-704 shown). HMS-4X Main Station (digital main station). Partyline channel 1 P2 Partyline channel 2 P3 Partyline channel 3 P4 Partyline channel 4 PF Program Feed C D E F In a traditional analog partyline system, one cable is dedicated to each partyline channel.
3.1.2 Topologies HelixNet Partyline can be deployed using a wide range of topologies, both complex and straightforward. The following table describes three standard types of topology: Topology Description Daisy-chain In a daisy-chain topology, the main station is connected to the first unit. The units are then connected in a series, using the passthrough connector on the back / rear of the device to pass on the connection. No termination is required.
A 1 B 2 4 8 7 C 3 9 5 XLR Bulkhead (passive) 6 7 Mult-box (passive) 5 Optional redundancy flyback 1 2 8 3 6 4 9 10 Figure 3-2: Example system topologies (layouts) 38 HelixNet Partyline User Guide 10
Key to example system topologies (layouts) diagram Feature A B C Description HMS-4X Main Station (digital main station) (rear panel). There are two lines (digital partylines) on the main station, each of which can support up to 10 digital HBP-2X beltpacks. There are two connectors (3-pin XLR, male and female) for each line. Daisy chained HBP-2X Beltpacks.
3.2 Installing the Main Station/Remote Station The Main Station/Remote station is a 19” 1RU-height device that you can install to either: • A standard 19” rack. • A shelf, cabinet or other flat surface. 3.2.1 Main Station power up There is no power switch, button or key on the Main Station. To power up the unit: 1) 2) Connect the power cord to the power supply connector on the Main Station. Note: The Main Station has a cable retaining clip to secure the power cord.
3.3.1 Speaker Station in an S-Mount bracket Figure 3-3 Speaker Station in S-Mount bracket You can adjust the S-Mount bracket by pressing one of the release buttons on either side of the bracket. You can adjust the bracket in 10-degree steps from 80 degrees to horizontal. Indicators are present beside the release buttons that show the adjustment steps. To install the Speaker Station: 1) Connect a powerline XLR-3 port on the Speaker Station to a powerline XLR-3 port on a Main Station.
3) Hang the S-Mount bracket on the wall screws. 4) Tighten the wall screws. 5) Install the Speaker Station. Figure 3-4 S-Mount bracket with keyholes 3.3.3 Speaker Station mounted inside a NEMA standard 4-gang wallbox To connect the Speaker Station: 1) Connect the Digital Intercom screw terminals on the Speaker Station to a powerline XLR-3 port on an HMS-4X. Or Connect an Ethernet port on the Speaker Station to an Ethernet port on an HMS-4X HLI-ET2 option module.
3.4 Installing the HBP-2X Beltpacks The HBP-2X Beltpack is a device that you can: • Wear at your belt using the beltclip. • Install to a shelf or other flat surface. • Attach to a pole or other fixed upright position. For more information, see 2.5.3 HBP-2X beltclip, beltloops and feet (base view) 3.4.1 Power up The HBP-2X Beltpack is powered from the standard mic cable that connects the device with the HMS-4X Main Station (see below). 3.4.
4 Configuring and managing the Main Station This chapter describes how to configure the settings and manage the Main Station using Menu mode. It also shows you how to monitor and diagnose performance issues, using the Diagnostics menus. Tip: For a quick reference to the Main Station menus, see 16 Menu maps. 4.1 Using the Menus To place the main station in Menu mode, press the Menu key to the left of the first display screen. In Menu mode, the display screens display the four levels of menu.
4.2 Configuring the Audio settings 4.2.1 Audio settings for the headset To configure the audio settings for the headset: 1) In Menu mode, select Audio Settings and then Headset. 2) To adjust the level of sidetone on the headset: a) In the third menu, select Sidetone Gain. b) In the fourth menu, select one of the following: • 0dB • - 6dB • - 12dB (default) • - 18dB c) To enable (confirm) the selected setting, press the rotary control.
5) To select the type of microphone on the headset: a) In the third menu, select HS Mic Type. Note: HS = Headset. b) In the fourth menu, select either of the following types of microphone: • Electret (-15dB) • Dynamic (0dB) (default) • Dynamic (-10 dB) c) To confirm the selected setting, press the rotary control. 4.2.2 Audio settings for the microphone To configure the audio settings for the microphone: 1) In Menu mode, select Audio Settings and then Microphone.
3) From the fourth menu, select one of the following: • + 12dB • + 6dB • 4) 0dB (default) • - 6dB • - 12dB To confirm the selected setting, press the rotary control. The GPO trigger activates a relay when receiving a call or activating a talk on a partyline channel. You can enable or disable the GPO trigger. To configure the audio setting for the GPO trigger: 1) In Menu mode, select Audio Settings and then Program Input. 2) From the third menu, select GPO Trigger.
3) 4.2.4 To confirm the selected setting, press the rotary control. Audio settings for Program IFB [Interruptible Foldback] IFB allows you to temporarily interrupt the continuous program listen (program feed) and speak to the channels connected to the program listen. See also 4.4.2 Assigning the Program Listen to a channel. To configure the audio settings for Program IFB [Interruptible Foldback]: 1) In Menu mode, select Audio Settings and then Program IFB. 2) From the third menu, select IFB Dim Level.
4.2.6 Audio settings for the Hot Mic Output To configure the audio settings for the Hot Mic Output: 1) In Menu mode, select Audio Settings and then Hot Mic Output. 2) From the third menu, select Gain. 3) From the fourth menu, select one of the following: • + 12dB • + 6dB • 4) 4.2.7 0dB (default) • - 6dB • -12dB To confirm the selected setting, press the rotary control.
4.3 Selecting Station Settings 4.3.1 Setting Preferences To set the Preferences: 4.3.2 1) In Menu mode, select Station Settings and then Preferences. 2) From the third menu, select Station ID, and enter a station ID with a maximum of 10 alphanumeric characters. For information about entering characters, see 4.4.1 Editing the channel label. 3) To confirm the selected setting, press the rotary control. Setting Keyset Assignments To set the Keyset Assignments: 4.3.
Tip: For a quick reference to the location of keys on the front panel, see 2.1Main Station/Remote Station: Front panel. 3) From the fourth menu, select either of the following: Note: 4) 4.3.4 • Latching • Non-latching The default for Talk Latch for the four available channels is Latching. The default for the SA Output key is Non-latching. To confirm the selected setting, press the rotary control.
4.3.6 Setting key brightness By default, the front panel keys are set to High / Low. To set the brightness of all front panel keys: 1) In Menu mode, select Station Settings and then Display. 2) From the third menu, select Key Brightness. 3) From the fourth menu, select one of the following brightness settings: Key(s) Description High / Low The default setting. Keys are lit bright when active and lit dim when inactive. High / Off Keys are lit bright when active and are unlit when inactive.
4.4 Configuring the channel settings 4.4.1 Editing the channel label The maximum length for a channel label is 10 characters. See 8.1.6 Resource Sharing between Linked Stations for an explanation of how identical labels are treated when Main Stations are linked. To edit the channel label: 1) In Menu mode, select Channels and then the name of the channel you want to edit. 2) From the third menu, select Label. 3) Select Clear and press the rotary control to clear the channel label.
4.4.2 Assigning the Program Listen to a channel To assign (or unassign) the Program Listen (Program Feed) to a channel: 1) In Menu mode, select Channels and then the name of the channel. 2) From the third menu, select Program Listen. 3) From the fourth menu, select either None, or choose from the list of available programs. Note: 4) Tip: 4.4.3 The default is None. To confirm the selected setting, press the rotary control.
4.5 Configuring the Control I/O The Control I/O connector (25 way female D-type) on the rear panel allows you to connect up to 4 relay outputs or 4 opto inputs and control them through the main station keysets: I/O type Description Opto inputs Opto inputs enable you to connect a foot switch or other control device and use it to trigger Call or Talk functions.
4.5.2 Configuring Relay outputs To configure the Control I/O for Relay outputs: 1) In Menu mode, select Control I/O. 2) From the second menu, select Outputs.
4.6 Configuring Module Settings Up to three optional interface modules can be fitted to the expansion bay of the HMS-4X Main Station. Warning: The interface modules are not hot pluggable. Ensure that the Main Station is powered down before inserting or removing modules. The Menu mode > Module Settings are used to set up the interface modules. Tip: 4.6.1 For more detailed information about interface modules, including pin out information, see: 2.2.1 HMS-4X Main Station rear panel: Interface modules.
4) The Program Output allows a program feed associated with the channel assigned to the four wire port to either be delivered to that 4 wire port alongside the other channel audio or not. To set the Program Output: a) From the third menu, select Program Output. b) From the fourth menu, select one of the following: • Unmute • Mute (default) 5) To confirm the selected setting, press the rotary control.
9) If you are setting up a continuous audio (program) feed using the four-wire interface module, then you may want to enable the VOX functionality. To help reduce redundant noise, the VOX functionality automatically deactivates and activates the continuous audio feed, at an automatically determined volume threshold. Note: If you assign a program and a four-wire interface to the same channel, VOX is automatically enabled. To enable or disable VOX: a) From the third menu, select VOX.
2) From the second menu, select one of the two available ports on the two-wire interface module: Slot 1/Port A 2W Slot 1/Port B 2W Note: In this example, the two-wire module has been fitted to slot 1 in the expansion bay. The expansion bay contains three slots. 2W = Two-wire. a) To associate one of the four available channels (or to disable channels associations) with the selected port: From the third menu (third display screen), select Channel Assign.
6) The Two-wire interface module is set for Clear-Com systems by default. However, you can also set the two-wire ports for use with RTS analog partyline systems. If you are connecting to an RTS system, you also have a choice of two different pinouts: RTS pinout option Description RTS Audio Pin 2 Pin 2 is used for both power and audio. RTS Audio Pin 3 Pin 3 is used for audio (Pin 2 is used for power only).
8) To set the Output Gain: a) From the third menu, select Output Gain. b) From the fourth menu, select one of the following: • +3 dB • +2 dB • +1 dB • 9) 0 dB (default) • -1 dB • -2 dB • -3 dB Enabling RMK [Remote Mic Kill] Input allows an external source such as the main (base) station of the connected two-wire system to send an RMK signal to the analog beltpacks attached to the HelixNet main station.
a) From the third menu, select VOX. b) From the fourth menu, select one of the following: • Enabled • Disabled (default) c) To confirm the selected setting, press the rotary control. 12) The VOX Delay OFF setting determines the length of time to wait before deactivating the incoming audio. To set the VOX Delay OFF setting: a) From the third menu, select VOX Delay OFF. b) From the fourth menu, select one of the following: • .
c) From the third menu, select Link Station. d) From the fourth display screen, select one of the following: 3) • Disabled (default) • Enabled To enable or disable DHCP: a) In Menu mode, select Networking. Note: The Networking menu only appears if an Ethernet or Fiber interface module is detected. b) From the second menu, select Preferences. c) From the third menu, select DHCP.
d) From the fourth display screen, edit the gateway. Note: 6) You can only edit the gateway if DHCP is disabled. To edit the Subnet Mask: a) In Menu mode, select Networking. Note: The Networking menu only appears if an Ethernet or Fiber interface module is detected. b) From the second menu, select Preferences. c) From the third menu, select Subnet Mask. d) From the fourth display screen, edit the Subnet Mask. Note: 4.6.4 You can only edit the Subnet Mask if DHCP is disabled.
4.7.2 Updating the software Any HBP-2X beltpacks, Remote Stations and Speaker Stations that are connected to the Main Station are automatically updated. The units remain non-functional for approximately 5 minutes while they are updated. To update the software: 1) After downloading the software update, copy the update to a USB memory stick. 2) Insert the memory stick into the USB 2.0 (A) connector. See Table 2-3 Key to Main Station/Remote Station front panel diagram.
Note: Do not remove the USB memory stick from the Main Station until the software update is completed, including the update to any connected devices. Do not turn off the power to the Main Station during the software (firmware) update. Turning off the power can damage the device. Note: 4.7.3 The Main Station resets automatically. You are not required to restart the Main Station. To check that the software upgrade was performed successfully, see 4.7.1 Viewing the current versions of the software.
4.7.5 Manually rebooting the Main Station To manually reboot the Main Station: 1) In Menu mode, select Administration and then Reset. 2) The third menu select Reboot. 3) In the fourth menu, select Reboot Now. When the rotary control is pressed, the display changes to Rebooting … for 2 seconds, and then the Main Station reboots. 4.7.6 Saving and restoring the software settings. To save or restore the software settings: 1) Insert a memory stick into the USB 2.0 (A) connector.
2) From the third menu, select one of the following: Note: • Main PCB • Slot 1 PCB • Slot 2 PCB • Slot 3 PCB Slot 1, Slot 2 and Slot 3 refer to the interface module slots in the Main Station extension bay. When looking at the rear of the module, slot 1 is the left-hand slot, slot 2 is the middle slot, and slot 3 is the right-hand slot. The fourth menu displays the Part number, Revision and Serial numbers for the PCB.
To view line information and status: 1) In Menu mode, select Diagnostics and then Powerlines. 2) From the third menu, select one of the following: 3) • Powerline 1 (refers to Line 1) • Powerline 2 (refers to Line 2) The fourth menu displays the status and other measures / information for the powerline. The status of the powerline is either Ok [operating normally], Busy or Error. For more details of the information displayed, see 16 Menu maps.
5 Configuring and managing the Remote Station This chapter describes how to configure the settings and manage the Remote Station using Menu mode. It also shows you how to monitor and diagnose performance issues, using the Diagnostics menus. Tip: For a quick reference to the Remote Station menus, see 16 Menu maps. For general information about using the menus and configuring settings, see 4.1 Using the Menus.
3) To select the IFB dim level: a) From the third menu, select IFB Dim Level. Note: The IFB Dim Level determines the volume level the Program Level is reduced to when it is interrupted by the IFB. b) From the fourth menu, select one of the following: • IFB Disabled (default) • - 6dB • -12dB • -18dB • -24dB • Full Cut c) To confirm the selected setting, press the rotary control. 4) The GPO trigger activates a relay when receiving a call or activating a talk on a partyline channel.
b) From the fourth menus, select one of the following: • .5 sec (default) • 1 sec • 2 sec • 3 sec • 4 sec c) To confirm the selected setting, press the rotary control. 5.1.4 Audio settings for the SA (Stage Announce) output To configure the settings for the SA output: 1) In Menu mode, select Audio Settings and then SA/Audio out. 2) To select the mode: a) From the third menu, select Mode.
b) From the fourth menu, select one of the following: • Unmute (default) • Mute • [SA Mode] c) To confirm the selected setting, press the rotary control. 5) To associate one of the four available channels (or to disable channels associations) with the selected port: a) From the third menu, select Channel Assign.
3) To select the Mode: a) From the third menu, select Mode. b) From the fourth menu, select one of the following: 5.2.2 • Intercom • Expansion panel. This allows a Remote Station to be co-located with another Remote Station and used as an additional four keysets. In that mode, the expansion panel's other connectors and controls will not operate. Setting Keyset Assignments To configure the Keyset Assignments settings, see 4.3.2 Setting Keyset Assignments. 5.2.
5.4 Configuring the Control I/O The Control I/O connector on the rear panel allows you to connect one relay output or one opto input and control them through the Remote Station keysets: I/O type Description Opto inputs Opto inputs enable you to connect a foot switch or other control device and use it to trigger Call or Talk functions.
5.4.2 Configuring the Relay output To configure the Control I/O for the Relay output: 1) In Menu mode, select Control I/O. 2) From the second menu, select Outputs. 3) From the third menu, select Relay 1 4) From the fourth menu, select one of the following: Note: 5) 5.
2) From the third menu, select DHCP. a) Select one of the following: 5.6 • Enabled (default) • Disabled 3) From the third menu, select IP Address, and enter the correct IP address. 4) From the third menu, select Gateway, and enter the correct gateway address. 5) From the third menu, select Subnet Mask, and enter the correct subnet mask Administration In Menu mode > Administration, you can: • View the current versions of the software for the system. • Update the software (firmware).
5) The fourth menu displays the new software version information on the USB memory stick. To start updating the Main Station with the new software, press the rotary control. The process of updating the software takes several minutes. The following system messages are displayed during the process: Loading image Erasing flash Writing to flash Verifying flash Successful Do not turn off the power to the Remote Station during the software (firmware) update. Turning off the power can damage the device.
5.6.5 Saving and restoring the software settings. To save or restore the software settings: 1) In Menu mode, select Administration and then Settings. 2) To save, in the third menu, select Save. Once you select Save you should not remove the USB stick right away. Depending on the USB stick it might take up to 5 seconds to complete. a) In the fourth menu, select between saving to a USB stick or saving locally. 3) To restore, in the third menu, select Restore.
3) To view status information about the Ethernet: a) From the third menu, select Ethernet. b) On the fourth menu, the IP address is given. 5.7.3 Viewing keyset information To view information about the keysets: 1) In Menu mode, select Diagnostics and then Keysets. 2) From the third menu, select a keyset from 1 to 4.
6 Configuring and managing the Speaker Station This chapter describes how to configure the settings and manage the Speaker Station using Menu mode. It also shows you how to monitor and diagnose performance issues, using the Diagnostics menus. Tip: For a quick reference to the Speaker Station menus, see 16 Menu maps. For general information about using the menus and configuring settings, see 4.1 Using the Menus.
6.2.2 Audio settings for the microphone To configure the audio settings for the microphone, see 4.2.2 Audio settings for the microphone. 6.2.3 Audio settings for the Front Panel To configure the audio settings for the front panel, see 4.2.7 Audio settings for the Front Panel. 6.3 Station Settings 6.3.1 Setting Preferences To set the Preferences, see 5.2.1 Setting Preferences 6.3.2 Setting Keyset Assignments To configure the Keyset Assignments settings, see 4.3.2 Setting Keyset Assignments. 6.3.
6.5 Administration 6.5.1 Viewing the current versions of the software To view the current version of the software, see 5.6.1 Viewing the current versions of the software. 6.5.2 Updating the software To update the software, see 5.6.2 Updating the software. Note: 6.5.3 You can only update the Speaker Station software from the Main Station. Resetting the Speaker Station to default (factory mode) settings. To reset the Speaker Station to its default (factory mode) settings see : 6.5.
7 Configuring and managing the HBP-2X Beltpack This chapter describes how to configure the settings and manage the HBP-2X Beltpack using Menu mode. It also shows you how to monitor and diagnose performance issues, using the Diagnostics menus. Tip: 7.1 For a quick reference to the Main Station menus, see 16 Menu maps. Using the Menus To place the beltpack in Menu mode, press the Menu key on the top of the beltpack. Note: The Beltpack menu comes up in the Beltpack Settings menu by default.
7.2 Configuring the Audio settings To configure the audio settings for the headset: 1) In Menu mode press the left-hand Call Key and then select Audio Settings. 2) To adjust sidetone gain on the headset: a) Select Sidetone Gain. b) Select one of the following: • 0dB • - 6dB • -12dB (default) • -18dB c) To confirm the selected setting, press the right-hand Call key. Go back to the previous menu level by pressing the left-hand Call key.
5) To set the type of mic on the headset: a) Select HS Mic Type. b) Select either of the following types of mic. Note: • Electret (-15 dB) • Dynamic (0 dB) (default) • Dynamic (-10 dB) In electret mode, phantom power is provided for an electret mic. In dynamic mode, no phantom power is provided. Mic input levels are also adjusted between the different modes to suit the different mic types. c) To confirm the selected setting, press the right-hand Call key. 7.
7.4.1 Assigning channels You can assign any two available channels to the beltpack (including the same channel to both keysets). To assign a channel: 7.4.2 1) In Beltpack Settings select Left Channel or Right Channel. 2) Select one of the available channels (or none): 3) To confirm the selected setting, press the right-hand Call key.
7.5 Configuring the Display Settings In Menu mode > Display Settings, you can: • Set the brightness of the display screen. • Set the brightness of the Talk and Call keys. • Enable (or disable) the screensaver. • Rotate the display. 7.5.1 Setting display screen brightness By default, the display screen is set to medium brightness. To set the brightness of the display screen: 1) In Menu mode, press the left-hand Call Key and then select Display Settings. 2) Select OLED Brightness.
7.5.3 Setting the screensaver The screensaver is displayed on screen after 10 minutes of inactivity on the beltpack. To enable (or disable) the screensaver: 1) In Menu mode, press the left-hand Call Key and then select Display Settings. 2) Select Screensaver. 3) Select one of the following: 4) 7.6 • Enabled (default) • Disabled To confirm the selected setting, press the right-hand Call key. Administration In Menu mode > Administration, you can: • View the IP address for the network.
7.6.2 Resetting the beltpack to default (factory mode) settings To reset the beltpack to default (factory mode) settings: 7.7 1) In Menu mode, press the left-hand Call Key and then select Administration. 2) Select Reset to Default. 3) Reset Now is displayed (shown as selected). To reset the beltpack, press the righthand Call key. Diagnostics The Diagnostics menus help you to monitor the performance of the beltpack and diagnose possible system issues. 7.7.
8 Linking Main Stations This chapter describes how to link Main Stations. You can connect Main Stations directly using Ethernet or Fiber, or connect them over a LAN via Ethernet. Main Station linking is achieved using interface modules fitted to the extension bay of the Main Station. There are two modules: • Ethernet interface module (HLI-ET2). This module provides an Ethernet connection between Main Stations. • Fiber interface module (HLI-FBS).
8.1.1 Linking two Main Stations with Ethernet 1) Insert an HLI-ET2 Ethernet interface module in each station. Use any of the three slots available. Note: Note: Ensure that the Main Station is powered down before inserting modules. 2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6, CAT6e) from one HLI-ET2 port on one station to one HLI-ET2 port on the other station. 3) Power up both stations. Verify that the green LED on each HLI-ET2 port is flashing.
8.1.2 Linking two Main Stations with Fiber 1) Insert an HLI-FBS Fiber interface module in each station. Use any of the three slots available. Note: Ensure that the Main Station is powered down before inserting modules. 2) Ensure that an SFP Transceiver is connected into one HLI-FBS module port on each station. 3) Connect Two Fibers from one HLI-FBS port on one station to one HLI-FBS port on the other station. If using Single connector fiber, make sure that Tx on one goes to Rx on the other.
8.1.3 Linking three Main Stations in a daisy chain You can daisy chain stations following all the instructions of the previous sections using the second port on one of the HLI-ET2 or HLI-FBS module to connect to a third station. Then enable linking on the third station. The advantage of daisy chain is that it does not require any additional equipment for interconnection.
8.1.4 Network connections Connecting in an existing IP network requires planning with your IT department in order to plan the IP addressing scheme. By default HelixNet Main Station uses automatic IP addressing (DHCP) enabled. In order for that to work properly in an existing IP network there must be a DHCP server handing out IP addresses. If no DHCP server is found, a Main Station will revert to an unused link-local address in the 169.254.0.0/16 block.
8.1.5 Multiple Groups in the same IP Network You can have multiple groups of Main Stations linked together. Each group must be part of a different subnet. Here is an example of IP addresses and subnets that would allow two independent groups of Main Stations in the same IP network. IP: 192.168.2.221 Netmask: 255.255.255.0 IP: 192.168.3.221 Netmask: 255.255.255.0 IP: 192.168.2.153 Netmask: 255.255.255.0 IP: 192.168.3.148 Netmask: 255.255.255.0 IP Network IP: 192.168.2.17 Netmask: 255.255.255.0 IP: 192.
8.1.6 Resource Sharing between Linked Stations The number of partyline channels available in your system will increase by 4 for each Main Station linked together. At the moment of linking, channels with exactly the same name will merge their audio together then only one will remain. When that happens, an additional channel name will be automatically generated (Ch 98798E-b in the following example). Once linked, each Main Station still “owns” 4 channels.
The following tables show how the labels appear before and after linking.
8.2 Networking Specifications Specification Value Latency on Powerline 40-80ms (Depends on cable type and length, and how many devices are connected. The greater the number of devices, the greater the latency.
9 Linking Remote Stations and Speaker Stations This chapter describes how to pair Remote and Speaker Stations to Main Stations. You can connect Remote and Speaker Stations on one of the Digital Intercom Lines, point-to-point to a Main Station Ethernet interface module (HLI-ET2) or over an IP network. Pairing to a Main Station over an IP network requires an Ethernet interface module fitted to the extension bay of the Main Station (HLI-ET2).
9.1 Pairing scenarios There are various topologies that you can create. Some of these are illustrated below. 9.1.1 Digital Intercom Remote and Speaker Stations have Digital Intercom 3-pin XLR connectors (female and male) and can connect to Main Stations along with Beltpacks. Note: A Remote or a Speaker Station draws current equivalent to three Beltpacks when the loudspeaker is in use.
9.1.2 Ethernet point-to-point link Remote and Speaker Stations have RJ45 Ethernet connectors and can connect to Main Stations over Ethernet. 1) Insert an HLI-ET2 Ethernet interface module in the Main Station. Use any of the three slots available. Note: Ensure that the Main Station is powered down before inserting modules. 2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6, CAT6e) from one HLI-ET2 port on one station to the Remote or Speaker Station.
9.1.3 Local IP Network 1) Insert an HLI-ET2 Ethernet interface module into the Main Station. Use any of the three slots available. Note: Ensure that the Main Station is powered down before inserting modules. 2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6, CAT6e) from one HLI-ET2 port to an Ethernet Switch and connect Remote or Speaker Stations to Ethernet Switch as well.
9.1.4 Remote IP Network Remote and Speaker Stations can connect to a Main Station that is not within the same network Broadcast Domain. 1) Insert an HLI-ET2 Ethernet interface module in the Main Station. Use any of the three slots available. Note: Ensure that the Main Station is powered down before inserting modules. 2) Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6, CAT6e) from one HLI-ET2 port to a Router/Gateway. Make sure you know the Gateway IP address for that first subnet.
HMS-4X Line 2 Line 1 Ethernet Router / Gateway IP Network Ethernet Router / Gateway HKB-2X HRM-4X 106 HelixNet Partyline User Guide
9.1.5 Mixed Pairs Here is one example of how all the previous pairings could be mixed with Main Station Linking. HMS-4X Line 2 Line 1 HKB-2X HKB-2X HMS-4X HKB-2X (with Power Sypply) Line 1 Ethernet Switch Line 2 HRM-4X (with Power Supply) Ethernet Switch (PoE) HRM-4X (PoE) 9.2 HKB-2X (PoE) Networking Specifications Specification Value Latency on Powerline 40-80ms (depends on the distance and the number of Devices (HBP, HRM, HKB) on the line.
10 Using the Main Station/Remote Station This chapter describes how to use the Main Station/Remote Station, after your HelixNet Partyline system has been installed and configured. For more information about integrating and using HelixNet Partyline with your existing intercom infrastructure, see 3 Installing HelixNet Partyline. Tip: 10.1 For a quick reference to the functionality of the HMS-4X Main Station, the optional interface modules and the HBP-2X Beltpack, see 2 Panels and Interfaces.
As you increase or decrease the volume, the level control LEDs pass through a range of indicator colors: LED color Volume level Green Low Amber / Green Low / Medium Amber Medium Red / Amber Medium / High Red High Table 10-1: Loudspeaker volume indicator colors To use a headset to talk and listen to connected intercom users, devices and systems: 1) Connect the headset, using the headset connector (4-pin XLR–M) on the far left of the front panel. The Headset key is automatically activated.
10.1.1 Switching between the headset mic and the gooseneck mic When both a Headset microphone and a gooseneck microphone are connected, press the Headset key to activate the headset mic. Press the Headset key again to switch to the gooseneck mic (and deactivate the headset mic). Tip: 10.2 To find out more about Clear-Com accessories, including headsets and gooseneck microphones, see http://www.clearcom.com/product/accessories.
2) Speak into the headset or gooseneck mic (see also 10.1 Using the gooseneck mic, loudspeaker and headset ). To adjust the volume of incoming audio, turn the rotary control. Turn the rotary control clockwise to increase the volume, and counter-clockwise to decrease volume. The current volume level is shown on screen. To mute incoming audio, press the rotary control. The display screen displays the muted volume bar.
10.7 Note: Line 1 and 2 LEDs This section only applies to the HelixNet Main Station. The HBP-2X beltpacks, Remote Stations and Speaker Stations are connected by one of the two lines to the Main Station. The color of the Line 1 and Line 2 LEDs to the left of the front panel loudspeaker indicate the service status of each powerline: • Green LED = Ok. • Amber LED = Busy. • Red LED = Error. For more information: • About the service status of Lines 1 and 2, see 4.8.3 Viewing powerline information and status.
11 Using the HBP-2X Beltpack This chapter describes how to use the HBP-2X Beltpack, after your HelixNet Partyline system has been installed and configured. For more information about integrating and using HelixNet Partyline with your existing intercom infrastructure, see 13 Connecting to Other Intercom Systems. Tip: 11.1 For a quick reference to the functionality of the HBP-2X Beltpack, the HMS-4X Main Station, and the optional interface modules, see 2 Panels and Interfaces.
11.2 Entering and exiting Menu mode Use Menu mode to: • Configure the settings for the Main Station, including channel and audio settings. • Monitor beltpack performance and diagnose issues. To enter Menu mode, press the Menu key. To exit Menu mode, press the Menu key again. For more information about using Menu mode on the beltpack, see 7 Configuring and managing the HBP-2X Beltpack. 11.3 Adjusting the Program Feed volume level.
12 Using the Speaker Station This chapter describes how to use the Speaker Station, after your HelixNet Partyline system has been installed and configured. For more information about integrating and using HelixNet Partyline with your existing intercom infrastructure, see 3 Installing HelixNet Partyline. 12.
To use a headset to talk and listen to connected intercom users, devices and systems: 4) Connect the headset, using the headset connector (4-pin XLR–M) on the far left of the front panel. The Headset key is automatically activated. Incoming audio is routed to the headset instead of the loudspeaker. Note: For the location of the headset connector and the headset key, see Table 2-24 Key to Speaker Station front panel Table 2-3 Key to Main Station/Remote Station front panel diagram.
To place the Speaker Station in Menu mode, press the Menu key to the left of the first (left) display screen. To exit Menu mode, do either of the following: • Press the Menu key again. • Wait until Menu mode times out. If you fail to press any key on the front panel for 20 seconds, the display screens revert to showing the standard channel information: Tip: 12.3 • Channel label (name). • Listen (volume) level.
12.4 Line and LAN LEDs The Speaker Station has a line LED that indicates the status of a powerline connection to the Main Station. The LAN LED indicates the status of the Ethernet connection, if present. The color of the Line and LAN LEDs to the left of the front panel loudspeaker indicate the service status of each powerline: • Green LED = Ok. • Amber LED = Busy. • Red LED = Error.
13 Connecting to Other Intercom Systems This chapter provides basic guidance on connecting your HelixNet Partyline system to a range of other intercom systems, including: • Two-wire cabled partyline systems (RTS and Clear-Com Encore®). • Two-wire / four-wire wireless systems (Tempest, CellCom® / FreeSpeak®, and the DX210). • Digital matrix systems (Eclipse® MVX four-wire). • Two way radio systems.
13.1.
13.1.3 Connecting to an Encore Main Station Note: The following procedure assumes that a two-wire interface module has been fitted to the HMS-4X Main Station. For more information about interface modules, see 2.2.1 HMS-4X Main Station rear panel: Interface modules. Note: A HelixNet system with HLI-2W2 must be able to receive power from an analog partyline.
Tip: If the headset microphone is being used, hum or gently scratch the mic for a continuous signal source to null on. If a good null is not attainable, switch the Long / Short DIP switch for the channel to its opposite setting. Use the setting that produces the best audio quality. To optimize audio quality, you may also want to adjust the Audio Settings on the HMS-4X Main Station. For more information, see 4.2 Configuring the Audio settings. 13.1.
13.2.
13.2.3 Connecting to an RTS (Telex) intercom station To connect your HelixNet Partyline system to an RTS intercom station (in this case, the 2 channel MCE325 user station): 1) On the HMS-4X Main Station, configure the Module Settings for the two-wire interface module. For the full procedure, see 4.6.2 Configuring a Two-wire interface module. Ensure that you: • Configure port(s) for RTS systems.
3) On the RTS device (in this case, the MCE325), adjust the nulling (if necessary) on the channel to which the HMS-4X Main Station is connected. Nulling helps to reduce echo while talking on a two-wire audio system. A sidetone nulling trimmer (control) is provided for each of the four channels on the device. To adjust a sidetone nulling trimmer: a) Turn the speaker switch on (even if an external speaker is not connected).
13.3.2 Quick reference: Two-wire connection to Tempest Two-wire connection to Tempest HMS-4X Main Station Configure the 2W module Configure the port as Clear-Com Run auto-null Standard mic cable / CAT-5 3-pin XLR connectors 2W Tempest Basestation Power supply Or Encore Main Station (MS-20x) Line must be powered (HMS-4X 2W module appears as unpowered beltpack / remote station to Tempest).
13.3.3 Two-wire connection to Tempest To connect your HelixNet Partyline system to Tempest, using a two-wire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the two-wire interface module. For the full procedure, see 4.6.2 Configuring a Two-wire interface module. Note: 2) Check that the Two-wire module is configured for Clear-Com systems (the default) and run Auto-null. Auto-nulling helps to reduce echo while talking on a two-wire audio system.
3) Physically connect the HelixNet Partyline and Tempest systems. Powering the connection: Tempest has a Master Mode setting that supplies power to the two-wire connection. In this case, no external power supply is required. Otherwise, you must power the connection between the systems using either a dedicated power supply (such as the PK-7, PS-702, or PS-704), or a powered Encore Main Station (such as the MS-702 or MS-704).
13.3.
13.3.5 Four-wire connection with Tempest To connect your HelixNet Partyline system with Tempest, using a four-wire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the Four-wire interface module, see 4.6.1 Configuring a Four-wire interface module. 2) On the Tempest Basestation, configure an intercom channel for four-wire connection: a) Select the intercom channel (A or B), using the CHAN selection button on the front panel.
13.4 Connecting HelixNet Partyline to CellCom® / FreeSpeak® 13.4.1 About CellCom / FreeSpeak CellCom / FreeSpeak is a wireless intercom system from Clear-Com, operating within the license-free 1.92-1.93GHz frequency band. The system is branded as CellCom in North America and as FreeSpeak in the rest of the world. CellCom /FreeSpeak combines DECT and wireless auto-roaming technologies to allow users to move freely without losing communication connection.
13.4.2 Quick reference: Two-wire connection to CellCom / FreeSpeak Two-wire connection to CellCom / FreeSpeak Standard mic cable / CAT-5 3-pin XLR connectors HMS-4X Main Station 2W CellCom / FreeSpeak Basestation Power supply Configure the 2W module Configure the port as Clear-Com Run auto-null Or Encore Main Station (MS-70x) Connect to CH-A or CH-B connectors Enable CH-A or CH-B.
13.4.3 Two-wire connection to CellCom / FreeSpeak To connect your HelixNet Partyline system to a CellCom / FreeSpeak basestation (Main Station), using a two-wire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the two-wire interface module. See 4.6.2 Configuring a Two-wire interface module. Note: 2) Check that the two-wire module is configured for Clear-Com systems (the default) and enable Auto-nulling.
13.4.
13.4.5 Four-wire connection to CellCom / FreeSpeak To connect your HelixNet Partyline system with a CellCom / FreeSpeak basestation (Main Station), using a four-wire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the four-wire interface module. For the procedure, see 4.6.1 Configuring a Four-wire interface module. 2) Connect the HMS-4X Main Station and the CellCom / FreeSpeak basestation, using four-wire crossover CAT5 cabling.
13.5.2 Quick reference: Two-wire connection to DX210 Two-wire connection to DX210 Standard microphone cable 3-pin XLR connectors HMS-4X Main Station Configure the 2W module Configure the port as Clear-Com Run auto-null DX210 Basestation (BS210) 2W Power supply Or Encore Main Station (MS-70x) Set Clear-Com / RTS button to Clear-Com (out position) Connect to either intercom channel (IC1 or IC2).
13.5.3 Two-wire connection to the DX210 To connect your HelixNet Party-line system to the DX210 basestation (Main Station), using a two-wire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the Two-wire interface module. For the procedure, see 4.6.2 Configuring a Two-wire interface module. Note: Check that the two-wire module is configured for Clear-Com systems (the default) and run Auto-null. Auto-nulling helps to reduce echo while talking on a two-wire audio system.
5) Apply auto-nulling to the connected channel (either IC1 or IC2) on the DX210 basestation. Auto-nulling helps to reduce echo while talking on a two-wire audio system. To apply auto-nulling: a) Insert a pen or similar pointed object into the AUTO-NULL hole on the front panel. b) Press and hold AUTO-NULL for 2 seconds. Note: 6) Tip: Before applying auto-nulling, ensure that there are no open microphones on the wired intercom.
13.5.
13.5.5 Four-wire connection to the DX210 To connect your HelixNet Partyline system with a DX210 basestation (BS210), using a fourwire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the Four-wire interface module. See 4.6.1 Configuring a Four-wire interface module. 2) Connect the HMS-4X Main Station and the DX210 basestation (BS210), using fourwire crossover CAT5 cabling. Note: For pinout information for the two systems, see the quick reference diagram in 13.5.
13.6.
13.6.3 Two-wire connection to an Eclipse or Eclipse-HX system frame To connect your HelixNet Partyline system to an Eclipse or Eclipse-HX System, using a twowire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the Two-wire interface module. For the procedure, see 4.6.2 Configuring a Two-wire interface module. Note: 2) Check that the two-wire module is configured for Clear-Com systems (the default) and run Auto-null.
Because the R, L and C controls interact, you may have to adjust these controls several times to minimize the test tone / achieve a deep null. Note: Tip: The null circuit on the CCI-22 is effective on line lengths between 0 - 4000 feet (1200m) with impedances in the range of 120 to 350 ohms. Nulling can reduce local audio in the received signal by < 30 dB over the 200 Hz - 8 kHz frequency range. For more information on the CCI-22 nulling circuit, see the CCI-22 Manual.
13.6.
13.6.5 Four-wire connection to Eclipse To connect your HelixNet Partyline system to an Eclipse or Eclipse-HX System, using a fourwire connection: 1) On the HMS-4X Main Station, configure the Module Settings for the four-wire interface module For the procedure, see 4.6.1 Configuring a Four-wire interface module. 2) Connect the HMS-4X Main Station directly to the MVX-A16 card (the 16 port audio and data card set) with standard CAT5 cable.
13.7.
13.7.2 Four-wire and control connection to radio system To connect the HelixNet Partyline to a radio system using four-wire: 1) In the Modules Settings menu, select Slot n/Port A/B 4W > Channel Assign > Channel # to assign the 4W port to a Channel, for example Channel A. 2) In the Modules Settings menu, select Slot n/Port A/B 4W > GPO Trigger > Disable to set GPO Trigger to Disable for that 4W port. 3) In the Channels menu, select Channel # > GPO on Talk > Relay # to select a Relay.
13.7.
13.7.4 Two-wire and control connection to radio system The two-wire connection uses a TW-47 radio interface. Because this has no power supply, you must use an Encore Main Station to supply power. You can also use an alternative source of power, such as a PK-7, PS-702 or PS-704. The diagram in Figure 13-12 shows a system using an Encore Main Station. To connect the HelixNet Partyline to a radio system using two-wire: 1) Connect the HelixNet Partyline to the Encore Main Station. For details, see 13.
13.7.
To connect the HelixNet Main Station to a radio system using four-wire: 1) In the Audio Settings menu, select PGM/Audio In > GPO Trigger > Disable. 2) In the Audio Settings menu, select SA/Audio Out Mode > Channel Assign. 3) Assign the SA/Audio Out to a Channel. 4) In the Channel configuration select the Remote Station Program under the Program Listen menu. 5) In the Channels menu, select Channel # > GPO on Talk > Relay 1. 6) Connect the audio and the Relay to the radio base station.
14 Specifications 14.1 Main Station (HMS-4X) 14.1.1 Connectors Specification Description / value Intercom Powerline Outputs Four 3-pin XLR. Two male and two female. Headset 4-pin XLR–M USB USB Type A and Micro-AB Program 3-pin XLR–F SA (Stage Announce) 3-pin XLR–M Hot Mic / IFB Interface 1/4 in. (0.64 cm) phone jack GPIO 25 way D-type female Table 14-1: Main Station: Connectors 14.1.
Load impedance 32Ω Output level +12dBu before clipping Sidetone -12dB (selectable) The following specified for a route from a 4-wire input @ 0dBu in Max gain 0dB Frequency response 40Hz - 10kHz ± 3dB Distortion <0.1% THD @ 1kHz Noise <-65dBu Headphone limiter 0dBu (selectable) Table 14-3: Main Station: Headphone amplifier 14.1.
14.1.5 Program line input and Four-wire option module inputs Specification Description / value Maximum level before clipping 18dBu Nominal input level 0dBu (selectable) Input impedance >= 10KΩ The following specified for a route to 4-wire output @ 0dBu out Frequency response 20Hz - 10kHz ± 3dB Distortion <0.2% THD @ 1kHz Noise <-65dBu Table 14-5: Main Station: Program line input and four-wire option module inputs 14.1.
14.1.7 Stage Announce outputs Specification Description / value Maximum level before clipping 18dBu Nominal output level 0dBu (selectable) Output impedance <= 100Ω The following specified for a route from a dynamic headset Frequency response 300Hz – 12kHz ± 3dB Distortion <0.1% THD @ 1kHz Noise <-55dBu Table 14-7: Main Station: Stage Announce outputs 14.1.
14.1.9 Helix Digital Partyline Specification Description / value Maximum level before clipping 6dBu Nominal input level -18dBu (C-C) -12dBu (RTS) Input impedance >= 10KΩ bridging The following specified for a circuit to a 4-wire output @0dBu in: Frequency response 100Hz - 10 kHz ± 3dB Distortion <0.2% THD @ 1kHz Noise <-55dBu The following specified for a circuit from a 2-wire input @0dBu out: Frequency response 40Hz - 10kHz ± 3dB Distortion <0.
14.1.11 Mains power Specification Description / value Input Voltage range 100 – 240VAC Input frequency range 50 – 60Hz Input power <=250W Powerline Intercom Output Voltage 59VDC ± 1V Output current per channel 1.5A (continuous) Table 14-11: Main Station: Mains power 14.1.12 Environmental Specification Description / value Temperature 0˚C - 40˚C (32˚F - 104˚F) Humidity 0 - 90% relative humidity Table 14-12: Main Station: Environmental 14.1.
14.2 Two-wire module (HLI-2W2) 14.2.1 Connectors Specification Description / value Intercom line (2) 3-Pin XLR-F Table 14-14: two-wire module: Connectors 14.2.2 Dimensions and weight Specification Description / value Dimensions 7.05 in. H x 2.24 in. W x 1.54 in. D (179 x 57 x39 mm) Weight 13 oz. (0.35 kg) Table 14-15: Two-wire module: Dimensions and weight 14.2.3 Power requirements (external) Specification Description / value Per channel 0.
14.3 Four-wire module (HLI-4W2) 14.3.1 Connectors Specification Description / value Intercom line (2) RJ-45 (Ethercon) Table 14-18: Four-wire module: Connectors 14.3.2 Dimensions and weight Specification Description / value Dimensions 7.05 in. H x 2.24 in. W x 1.54 in. D (179 x 57 x39 mm) Weight 13 oz. (0.35 kg) Table 14-19: four-wire module: Dimensions and weight 14.3.
Table 14-21: Remote Station: Connectors 14.4.2 Microphone pre-amplifier Specification Description / value Headset Mic impedance: 200 Ω (Dynamic) Headset Mic Voltage 1.7V (Electret selectable) Limiter +23 dB The following specified for a route to 4-wire output @ 0dBu out Mic gain 60dB (dynamic) 45dB (electret) Frequency response 300 Hz – 10 kHz + / -3dB (contoured for intelligibility) Distortion <0.
Load impedance 8Ω Output level +18dBu before clipping Max gain 18dB The following specified for a route from a 4-wire input @ 0dBu in Frequency response 200 Hz - 10 kHz ±3dB Distortion <1% THD @ 1 kHz Noise <-50dBu Table 14-24: Remote Station: Loudspeaker amplifier 14.4.
14.4.7 Stage Announce outputs Specification Description / value Maximum level before clipping 18 dBu Nominal output level 0dBu(selectable) Output impedance <= 100Ω The following specified for a route from a dynamic headset Frequency response 300Hz – 12kHz ±3dB Distortion <0.1% THD @ 1kHz Noise <-55dBu Table 14-27: Remote Station: Stage Announce outputs 14.4.
14.4.9 Helix Digital Partyline Specification Description / value Maximum level before clipping 6 dBu Nominal input level -18dBu (C-C) -12dBu (RTS) Input impedance >= 10KΩ bridging The following specified for a circuit to a 4-wire output @0dBu in: Frequency response 100Hz - 10 kHz ±3dB Distortion <0.2% THD @ 1 kHz Noise <-55dBu The following specified for a circuit from a 2-wire input @0dBu out: Frequency response 40 Hz - 10 kHz ±3dB Distortion <0.
14.4.11 Mains power Specification Description / value Input Voltage range 100 – 240 VAC Input frequency range 50 – 60 Hz Input power <=250W Powerline Intercom Output Voltage 59VDC ± 1V Output current per channel 1.5A (continuous) Table 14-31: Remote Station: Mains power 14.4.12 Environmental Specification Description / value Temperature 0˚C - 40˚C (32˚F - 104˚F) Humidity 0 - 90% relative humidity Table 14-32: Remote Station: Environmental 14.4.
Table 14-34: Speaker Station: Connectors 14.5.2 Microphone pre-amplifier Specification Description / value Headset Mic impedance: 200 Ω (Dynamic) Headset Mic Voltage 1.7V (Electret selectable) Limiter +23 dB The following specified for a route to 4-wire output @ 0dBu out: Mic gain 60dB (dynamic) 45dB (electret) Frequency response 300 Hz – 10 kHz + / -3dB (contoured for intelligibility) Distortion <0.
14.5.4 Ethernet Specification Description / value Fast Ethernet standard 100BaseT only, Auto MDIX Table 14-37: Speaker Station: Ethernet 14.5.5 Power requirements Specification Description / value Power requirements 4W DC Voltage range 30 – 60 Volts Table 14-38: Speaker Station: Power requirements 14.5.
14.6 Beltpack (HBP-2X) 14.6.1 Connectors Specification Description / value Intercom line Two 3-pin XLR. One male and one female. Headset 4-pin XLR–M and 2.5mm TRS jack USB Micro-AB TRS Headset 3.5mm mini jack Table 14-40: Beltpack: Connectors 14.6.2 Microphone pre-amplifier Specification Description / value Headset Mic impedance: 200 Ω (Dynamic) Headset Mic Voltage 1.
14.6.3 Headphone amplifier Specification Description / value Load impedance >32 Ω Output level +12dBu before clipping Sidetone -12dB (selectable) The following specified for a route from a 4-wire input @0dBu in: Max gain 0dB Frequency response 40 Hz - 10 kHz ±3dB Distortion <0.1% THD @ 1 kHz Noise <-65dBu (@ max gain) Headphone limiter -0dBu (selectable) Table 14-42: Beltpack: Headphone amplifier 14.6.
15 Compliance FCC notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
IEC 60065-7 Waste Electrical And Electronic Equipment (WEEE) The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturers, distributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE Directive covers most Clear-Com products being sold into the EU as of August 13, 2005.
16 Menu maps HMS-4X Main Station menu map Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Audio Settings Headset Sidetone Gain Range: 0dB to -18dB Default: -12db Headphone Limit Range: +6dB to -6dB Default: 0db Sidetone Control Tracking Non-Tracking Disabled Default: Tracking HS Mic Type Electret Dynamic (0 dB) Dynamic (-10 dB) Default: Dynamic (0 dB) Headroom Normal High Default: Normal Contour Filter Enabled Disabled Default: Enabled Gain Range: +12dB to -12dB Default: 0db GPO Trigge
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) VOX Off Delay Range: 0.5 – 4 sec Default: 0.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Low Default: Medium Channels Control I/O Channel A Channel B Channel C Channel D […] Inputs Key Brightness High / Low High / Off Low / Off Off / Off Default: High / Low Screensaver Enabled Disabled Default: Enabled Label Press to Edit Max.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Module Settings Slot n /Port A/B 4W Channel Assign Disabled Channel A Channel B Channel C Channel D Default: Disabled Program Output Unmute Mute Default: Mute GPO Trigger Enabled Disabled Default: Enabled Input Gain Range: +12dB to -12dB Default: 0db Output Gain Slot n /Port A/B 2W 174 HelixNet Partyline User Guide VOX Enabled Disabled Default: Disabled VOX Off Delay Range: [0].5 – 4 secs Default: [0].
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Program Output Unmute Mute Default: Unmute Auto-Nulling Start Mode Clear-Com RTS Audio Pin 2 RTS Audio Pin 3 Default: Clear-Com GPO Trigger Enabled Disabled Default: Enabled Input Gain Range: -3dB to +3dB Default: 0db Output Gain RMK Input RMK Output Network Enabled Disabled Default: Enabled VOX Enabled Disabled Default: Disabled VOX Off Delay Range: [0].5 – 4 secs Default: [0].
Menu 1 (First) > Administration Menu 2 > Menu 3> Menu 4 (Last ) Subnet Mask IP address: xx.xx.xx.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Keysets Keyset 1 Keyset 2 Keyset 3 Keyset 4 Name: Channel name Talkers: Number of talkers on party line Devices: Number of beltpacks listening on party line Main Stations: Number of Main Stations listening 2-Wire: Number of 2-Wire ports listening 4-Wire: Number of 4-Wire ports listening 177 HelixNet Partyline User Guide
HRS-4X Remote Station menu map Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Audio Settings Headset Sidetone Gain Range: 0dB to -18dB Default: -12db Headphone Limit Off + Range: +6dB to -6dB Default: 0db Sidetone Control Tracking Non-Tracking Disabled Default: Tracking HS Mic Type Electret Dynamic (0 dB) Dynamic (-10 dB) Default: Dynamic (0 dB) Headroom Normal High Default: Normal Contour Filter Enabled Disabled Default: Enabled Gain Range: +12dB to -12dB Default: 0db IFB Dim Level R
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) VOX Off Delay Range: 0.5 - 4sec Default: 0.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Station Settings Preferences Program ID Alphanumeric entry Default: HRM – [unique ID] Keyset Assign Keyset 1 – 4 None [conf_name_1], [conf_name_2], [conf_name_3], [conf_name_4] Default: [conf_name_1] Keysets Talk #1 Latch Talk #2 Latch Talk #3 Latch Latching Non-Latching Default: Latching Talk #4 Latch Display 180 HelixNet Partyline User Guide SA Output Key Latching Non-Latching Default: Non-latching RMK Enabled Disabled Default: Enabled
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Channels Channel A Channel B Channel C Channel D […] Label Press to Edit Max.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Control I/O Inputs Opto 1 Outputs Relay 1 None Call Key 1 Talk Key 1 Call Key 2 Talk Key 2 Call Key 3 Talk Key 3 Call Key 4 Talk Key 4 Default: None Pair to Station By Name By Address Separate IP address: xx.xx.xx.xx where x is a numeric value Preferences DHCP Enabled Disabled Default: Enabled IP Address IP address: xx.xx.xx.xx where x is a numeric value Gateway IP address: xx.xx.xx.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Diagnostics Powerlines Powerline 1 Status: [status] DMC: {MAC] HMC: [MAC] MMC: [MAC] Rx rate: [Mbps] Tx rate: [Mbps] Network Status IP Address IP Address IP Mask Mac Keysets Keyset 1 Keyset 2 Keyset 3 Keyset 4 HKB-4X Speaker Station menu map 183 HelixNet Partyline User Guide Name: Channel name Talkers: Number of talkers on party line Devices: Number of beltpacks listening on party line Main Stations: Number of Main Stations listening 2-Wire: Nu
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Audio Settings Headset Sidetone Gain Range: 0dB to -18dB Default: -12db Headphone Limit Off + Range: +6dB to -6dB Default: 0db Sidetone Control Tracking Non-Tracking Disabled Default: Tracking HS Mic Type Electret (-15dB) Dynamic (0 dB) Dynamic (-10 dB) Default: Dynamic (0 dB) Microphone Headroom Normal High Default: Normal Contour Filter Enabled Disabled Default: Enabled Front Panel Loudspeaker Dim Range: 0dB to --24dB Default: -6db Sta
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Keyset Assign Keyset 1 – 4 None [conf_name_1], [conf_name_2] Default: [conf_name_1] Keysets Talk #1 Latch Talk #2 Latch Latching Non-Latching Talk #3 Latch Default: Latching Talk #4 Latch Unlatch on Shift Enabled Disabled Default: Enabled Display OLED Brightness High Medium Low Default: Medium Key Brightness High / Low High / Off Low / Off Off / Off Default: High / Low Screensaver 185 HelixNet Partyline User Guide Enabled Disabled
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Default: Enabled Network Pair to Station By Name By Address Separate IP address: xx.xx.xx.xx where x is a numeric value Preferences DHCP Enabled Disabled Default: Enabled Administration Software IP Address IP address: xx.xx.xx.xx where x is a numeric value Gateway IP address: xx.xx.xx.xx where x is a numeric value Subnet Mask IP address: xx.xx.xx.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Keysets Keyset 1 Name: Channel name Talkers: Number of talkers on party line Devices: Number of beltpacks listening on party line Main Stations: Number of Main Stations listening 2-Wire: Number of 2-Wire ports listening 4-Wire: Number of 4-Wire ports listening Keyset 2 Keyset 3 Keyset 4 HBP-2X Beltpack menu map Menu 1 (First) > Menu 2> Menu 3 (Last ) Audio Settings Sidetone Gain Range: 0dB to -18dB Default: -12dB Headphone Limit Off + Range: +6
Menu 1 (First) > Menu 2> Menu 3 (Last ) Note: Electret = 35dB fixed gain, non-user adjustable. Dynamic = 50dB fixed gain, non-user adjustable.
Menu 1 (First) > Menu 2> Menu 3 (Last ) High / Off Low / Off Off / Off Default: High / Low Rotate Display Enabled Disabled Default: Disabled Screensaver Enabled Disabled Default: Enabled Menu 1 (First) > Menu 2> Menu 3 (Last ) Administration IP Address IP address: xx.xx.xx.xx where x is a numeric value Software Version npl-1.0.x, uboot Software Update npl-1.0.
Menu 1 (First) > Menu 2> Menu 3 (Last ) network (and which also powers the beltpack).
17 Cabling reference You can connect HBP-2X Beltpacks using: • A wide range of standard microphone (intercom) cable types (16 AWG – 26 AWG). • CAT5, CAT5e and CAT6 cable types.
17.2 Cable capacitance versus distance Standard microphone cables impose distance limitations at their upper limits due to cable capacitance. If your priority is audio quality, experiment with attaching one or two fewer devices to each line. Your choice of topology (daisy chain, star or tree) may also impact audio quality over distance.
17.2.1.
Remote Station Limit Distances 7 Number of Units 6 5 4 9463f 3 9207 9451 2 1 0 0 200 400 600 Limit Distance (meters) 194 HelixNet Partyline User Guide 800 1000
Speaker Station Limit Distances 7 Number of Units 6 5 4 9463f 3 9207 9451 2 1 0 0 200 400 600 800 1000 Limit Distance (meters) Note: The above graphs are intended as a general guide only. Actual cable performance may vary, depending on the conditions and complexity of the installation.
18 Troubleshooting Issue Solution Why are the Talk keys flashing periodically? Flashing Talk keys may indicate a fault in the cable. The Call functionality on my analog beltpack is no longer working. HelixNet Partyline operates at different voltage levels than analog two-wire partyline systems. Check the cable for short-circuit conditions and replace if necessary. The analog beltpack may have been damaged if it was connected to a HelixNet Main Station partyline port.
Line 1 (or Line 2) LED is steady red and one or more Beltpack has no bars showing up for signal strength. There are digital errors or there is cross-talk on that Powerline. Look at the Diagnostics->Powerlines>Powerline 1(or 2) page. If the number of Beltpacks showing there is greater than what you physically connected to that Powerline, crosstalk is happening between the Powerlines. Make sure you are using properly shielded Mic cables or Cat cables.
