Partyline User Guide PN: 399G052 Rev: B 06/19/13
Document Reference Clear-Com HelixNet Partyline User Guide Part Number: 399G052 Revision: B Legal Disclaimers Copyright © 2013 HME Clear-Com Ltd. All rights reserved. Clear-Com, the Clear-Com logo, and Clear-Com Concert are trademarks or registered trademarks of HM Electronics, Inc. The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of the agreement.
Contents Document Reference ................................................................................................................................ 2 1 Introduction ............................................................................................................. 9 1.1 Audience ....................................................................................................................................... 9 1.2 Important Safety instructions.....................................
.1.5 Multiple Groups in the same IP Network ............................................................................. 40 4.1.6 Resource Sharing between Linked Stations ....................................................................... 41 4.2 5 Networking Specifications ........................................................................................................... 43 Configuring and Managing the HMS-4X Main Station ....................................... 44 5.1 5.1.
.7.1 Viewing the current versions of the software ...................................................................... 65 5.7.2 Updating the software ......................................................................................................... 66 5.7.3 Locking and unlocking the HBP-2X beltpack menus .......................................................... 67 5.7.4 Resetting the Main Station to default (factory mode) settings. ........................................... 67 5.7.
7.3 Using the channel keysets .......................................................................................................... 83 7.4 Using the All Talk key .................................................................................................................. 84 7.5 Using the SA [Stage Announce] key ........................................................................................... 84 7.6 Using the RMK [Remote Mic Kill ] key ..............................................
9.5.4 Quick reference: Four-wire connection to DX210 ............................................................. 107 9.5.5 Four-wire connection to the DX210................................................................................... 108 9.6 Connecting HelixNet Party-line to Eclipse ................................................................................ 109 9.6.1 About Eclipse ............................................................................................................
10.4.3 Headphone amplifier ......................................................................................................... 124 10.4.4 Power requirements .......................................................................................................... 124 10.4.5 Environmental ................................................................................................................... 124 Appendix A: Compliance ...................................................................
1 Introduction This guide is intended to help you install, configure, and use the HelixNet Partyline™ system. HelixNet Partyline is a digital intercom system, featuring the award-winning I.V Core Technology from Clear-Com®. The system is designed to be as simple to use and configure as a two-wire intercom / analog Partyline system, while exploiting the flexibility and network management capabilities of a matrix system.
1.2 Important Safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
1.2.1 Safety symbols Familiarize yourself with the safety symbols in Figure 1: Safety symbols. These symbols are displayed on the apparatus and warn you of the potential danger of electric shock if the system is used improperly. Figure 1: Safety symbols Important note: For compliance notices, see Appendix A: Compliance. 1.3 Further information For the latest information about HelixNet Partyline, including software updates, see: http://www.clearcom.com/product/helixnet.
2 User Interfaces 2.
Key to HMS-4X Main Station: Front panel Feature Description A Ear for rack mounting Main Station. B Headset socket (4-pin XLR–M) Pin Function 1 Mic ground 2 Mic hot 3 Earphone ground 4 Earphone Table 2: Headset socket pin out C Gooseneck microphone socket (3-pin female Tuchel connector) D Mic control [ MIC ON]. Press to activate mic audio. E Headset key [ HSET]. Press to activate the headset mic. When the headset is connected, the gooseneck microphone is disconnected.
I LEDs for lines 1 and 2 (partylines). The LEDs indicate the status of the intercom circuit powering. When an LED is lit: • Green, the line is functioning. • Amber, the line is busy. • Red, there is an error or fault on the line. If there is a fault on a powerline output, the Line STATUS indicator for that channel will turn off and the red FAULT indicator will flash. Possible causes of a fault include overvoltage, overcurrent, short circuit to ground or severe brown-outs. B J Loudspeaker.
N All Talk. Press to talk to all channels (intercom devices and systems) connected to the main station. O USB 2.0 (Micro-AB) connector. For software upgrades (see 5.7.2 Updating the software and 5.7.5 Saving and restoring the software settings.). P USB 2.0 (Standard-A) connector. For software upgrades (see 5.7.2 Updating the software and 5.7.5 Saving and restoring the software settings.).
Key to HMS-4X Main Station front panel: Channel keyset Feature A Description Display screen. The following default information is displayed onscreen: • The channel label [ • The channel listen (volume) level [ ]. ]. In Menu mode, the display screens display the four levels of menu. The menu hierarchy proceeds left to right: • The top level menu is presented in the first screen (furthest left on the front panel).
2.
Key to HMS-4X Main Station: Rear panel Feature Description A Power supply with metal cable restrainer. The power supply operates at 100 - 240 VAC / 50-60Hz / 250 watts / T 3.15A H 250 V. B Control I/O (25 way female D-type). Use to connect up to 4 relay control outputs or 4 optically isolated control inputs (see 5.5 Configuring the Control I/O).
C Hot Mic output. This connection is a 1/4-in (0.64 cm) phone jack. It provides an output signal from the selected headset or panel microphone. The Hot Mic output is always live. Audio from the mic is routed through the Hot Mic output even if the mic is inactive (off). Pin Function Tip Mic Ring IFB mute signal Sleeve Ground Table 7: Hot Mic pin out D SA [Stage Announce] line out (3-pin male XLR).
G Line 2 (partyline). (3-pin male and female XLR connectors). Up to 10 beltpacks can be connected to a line, depending on the cable type and distance from the main station. Pin Function Pin 1 Ground Pin 2 +30V DC and Audio Pin 3 -30V DC and Audio Table 11: Line 2 pin out See Quick reference: Cable capacity versus distance on page 139. H Optional: Four-wire interface module (Ethercon type RJ45 connectors). For more information, see Table 16: HMS-4X Main Station rear panel: Interface Modules.
2.2.1 HMS-4X Main Station rear panel: Interface modules Up to three additional Interface modules (of the same or different types) can be fitted to the extension bay of the main station. When looking at the rear of the module, expansion slot 1 is the left-hand slot, expansion slot 2 is the middle slot, and expansion slot 3 is the right-hand slot. Warning: The interface modules are not hot pluggable. Ensure that the Main Station is powered down before inserting or removing modules.
Four-wire interface module (HLI-4W2) This is a two channel device that enables interoperability with the Eclipse digital matrix system and other four-wire audio sources (telephone hybrids, AB-120/-100, PA (Public Address) / SA (Stage Announce) systems.The module also enables HelixNet-to-HelixNet connections using four-wire audio ports.
Fiber interface module (HLI-FBS) Enables linking of Main Stations via a fiber link. Contains two SFP ports. Any 100BASE-X SFP can be connected. Warning: Both ports are configured to bridge traffic from one port to the other in order to work in daisy-chain. Spanning Tree Protocol is not enabled on those ports, therefore do not connect them both to the same network.. Table 16: HMS-4X Main Station rear panel: Interface Modules 2.3 HBP-2X Beltpack 2.3.
Key to HBP-2X user controls (front and side view) Feature A Description Menu key. Press firmly to enter Menu mode (see also press the Menu key again. D F ). To exit Menu mode, Note: The display screen times out of Menu mode and displays the channel label(s) if no key is pressed for 20 seconds. B USB 2.0 (Micro-AB) connector. For software upgrades. C Casing. Metal casing for robust use. For information about the beltclip, beltloops, and feet, see 2.3.
2.3.2 HBP-2X connectors and controls (rear view) E A B C D Figure 6: HBP-2X connectors and controls (rear view) ey to HBP-2X Beltpack (Rear view) Feature A B 25 Description Line (Partyline) (3-pin female XLR connector). Pin Function 1 Chassis 2 +30V DC and Audio 3 -30V DC and Audio Table 18: Line (female) pin out Line (Partyline) (3-pin male XLR connector). Pass-thru for ‘daisy chain’ connection (see Figure 9: Example system topologies (layouts)).
C Program feed (volume) scroll wheel. Turn to increase or decrease the overall listen volume level of the program feed. To assign programs to a channel, see 5.4.2 Assigning the Program Listen to a channel. D 2.5 mm TRS headset input. E Headset connector (4-pin or 5-pin XLR connector (male or female options)). The 5-pin female option is shown.
2.3.3 HBP-2X beltclip, beltloops and feet (base view) Figure 7: HBP-2X Beltpack: base view Key to HBP-2X Beltpack (Base view) Feature Description A Beltclip. The beltclip is secured to the unit with three screws, and may be removed, according to your requirements. Use the beltclip to attach the beltpack to a belt or a fixed position. B Feet (positions only). The beltpack can also be placed on a level surface (once the beltclip has been removed).
3 Installing HelixNet Partyline This chapter describes how to install your HelixNet Partyline system. It also provides basic guidance on planning your installation. Tip: For guidance on connecting HelixNet Partyline to other systems, using the optional interface modules, see 9 Connecting to Other Intercom Systems. Do not plug any non-approved equipment into HelixNet Partyline. HelixNet Partyline operates at different voltage levels than analog two-wire partyline systems.
3.1 Planning your HelixNet Partyline installation 3.1.
Key to analog and digital cabling comparison diagram Feature A B Description Example 4-channel analog main station (MS-704 shown). HMS-4X Main Station (digital main station). P1 Partyline channel 1 P2 Partyline channel 2 P3 Partyline channel 3 P4 Partyline channel 4 PF Program Feed C D E In a traditional analog partyline system, one cable is dedicated in hardware to each partyline channel.
3.1.2 Topologies (layouts) HelixNet Partyline can be deployed using a wide range of topologies, both complex and straightforward. The following table describes three standard types of topology: Topology Description Daisy-chain In a daisy-chain topology, the main station is connected to the first beltpack. The beltpacks are then connected in a series, using the pass-thru connector on the back / rear of the device to pass on the connection. No termination is required.
Figure 9: Example system topologies (layouts) 32 HelixNet Partyline User Guide
Key to example system topologies (layouts) diagram Feature A Description HMS-4X Main Station (digital main station) (rear panel). There are two lines (digital partylines) on the main station, each of which can support up to 10 digital HBP-2X beltpacks. There are two connectors (3-pin XLR, male and female) for each line. B Daisy chained HBP-2X Beltpacks. To create a ‘daisy chain’ of connected beltpacks: 1.
3.2 Installing HelixNet Partyline 3.2.1 Environmental information The recommended temperature ranges for HelixNet Partyline ( the HMS-4X Main Station and HBP-2X Beltpacks) are as follows: Operational statusa Temperature range (recommended) Min. In use (operational) In storage (non-operational) Max. 0 °C +50°C -30 °C +70°C Table 27: Recommended temperature ranges Install the HMS-4X Main Station at a site where there is adequate ventilation around the main station.
Power up There is no power switch, button or key on the HMS-4X Main Station. To power up the main station: 1. Connect the power cord [ ] to the power supply connector [ ] on the main station. Use the cable retaining clip on the main station to secure the power cord. The retaining clip is detached for shipping and must be refitted. Note: For the location of the power supply connector on the main station, see Table 12: Key to HMS-4X Main Station rear panel diagram. A in 2.
Connecting the HBP-2X Beltpack to the HMS-4X Main Station To connect the HBP-2X Beltpack to the HMS-4X Main Station: 1. There are two lines (partylines) on the main station, each of which can support up to 10 digital HBP-2X beltpacks. There are two connectors (3-pin XLR, male and female) for each line. Connect the cable to the selected connector [ ] on the main station.
4 Linking Main Stations This chapter describes how to link Main Stations to create a party line system that has more than four channels and more than 20 beltpacks. You can connect Main Stations directly or over a LAN via Ethernet. Main Station linking is achieved using interface modules fitted to the extension bay of the Main Station. There are two modules: • • Ethernet interface module (HLI-ET2). This module provides an Ethernet connection between Main Stations. Fiber interface module (HLI-FBS).
4.1.1 Linking two Main Stations with Ethernet 1. Insert an HLI-ET2 Ethernet interface module in each station. Use any of the three slots available. Note: Ensure that the Main Station is powered down before inserting modules. 2. Connect a regular Ethernet cable (for example, CAT5, CAT5e, CAT6, CAT6e) from one HLI-ET2 port on one station to one HLI-ET2 port on the other station. 3. Power up both stations. Verify that the green LED on each HLI-ET2 port is flashing. 4.
4.1.2 Linking two Main Stations with Fiber 1. Insert an HLI-FBS Fiber interface module in each station. Use any of the three slots available. Note: Ensure that the Main Station is powered down before inserting modules. 2. Plug an SFP Transceiver into one HLI-FBS port on each station. 3. Connect Two Fibers from one HLI-FBS port on one station to one HLI-FBS port on the other station. If using Single connector fiber,make sure that Tx on one goes to Rx on the other. 4. Power up both stations.
4.1.3 Linking three Main Stations in a daisy chain You can daisy chain stations following all the instructions of the previous sections using the second port on one of the HLI-ET2 or HLI-FBS module to connect to a third station. Then enable linking on the third station. You can daisy chain many stations this way but do not create a loop. The advantage of daisy chain is that it does not require any additional equipment for interconnection.
4.1.4 Network connections Connecting in an existing IP network requires planning with your IT department in order to figure out the IP addressing scheme. By default Helixnet Main Station comes up with automatic IP addressing (DHCP) enabled. In order for that to work properly in an existing IP network there must be a DHCP server handing out IP addresses. If no DHCP server is found, a Main Station will revert to an unused Link-local address in the 169.254.0.0/16 block.
4.1.5 Multiple Groups in the same IP Network You can have multiple groups of Main Stations linked together. Each group must be part of a different subnet. Here is an example if IP addresses and subnets that would allow two independent groups of Main Stations in the same IP network. IP: 192.168.2.221 Netmask: 255.255.255.0 IP: 192.168.3.221 Netmask: 255.255.255.0 IP: 192.168.2.153 Netmask: 255.255.255.0 IP: 192.168.3.148 Netmask: 255.255.255.0 IP Network IP: 192.168.2.17 Netmask: 255.255.255.0 IP: 192.
4.1.6 Resource Sharing between Linked Stations The number of partyline channels available in your system will increase by 4 for each Main Station linked together. At the moment of linking, channels with the exact same name will merge their audio together then only one of those will remain. When that happens, an additional channel name will be automatically generated (Ch 98798E-b in the following example). Once linked each Main Station still “owns” 4 channels.
Channel number Station 1 Labels 1 Sound 2 Stage 3 LD Private LD Private 4 Spots Spots 5 Station 2 Labels Linked Network Label Sound Stage Stage Lighting 6 Lighting Ch 98798E-b 7 Director Director 8 SPOTS SPOTS Table 29 Labels after enabling linking HLI-ET2 HLI-ET2 Figure 16:Resource sharing between unlinked stations 42 HelixNet Partyline User Guide “Owned” by Station 1 “Owned” by Station 2
Labels after link is severed Channel number Station 1 Labels Station 2 Labels Linked Network Label 1 Sound Sound “Owned” by Station 1 2 Stage Stage 3 LD Private LD Private 4 Spots Spots 5 Lighting Lighting 6 Channel 6 Channel 6 7 Director Director 8 SPOTS SPOTS “Owned” by Station 2 Table 30 Labels after link is severed 4.
5 Configuring and Managing the HMS-4X Main Station This chapter describes how to configure the settings and manage the HMS-4X Main Station using Menu mode. It also shows you how to monitor and diagnose performance issues, using the Diagnostics menus. Tip: For a quick reference to the main station menus, see Appendix B: Menu maps. 5.1 Using the Menus To place the main station in Menu mode, press the Menu key [ screen.
5.1.2 Exiting Menu mode To exit Menu mode, do either of the following: • Press the Menu key [ • Wait until Menu mode times out. If you fail to press any key on the front panel for 20 seconds, the display screens revert to showing the standard channel information: ]. • Channel label (name) [ • Listen level (volume) [ ]. ]. 5.2 Configuring the Audio settings 5.2.1 Audio settings for the headset To configure the audio settings for the headset: 1.
3. To limit the peaks in audio on the headphones (or to disable headphone limiting): a. In the third menu (third display screen), select Headphone Limit. b. In the fourth menu (fourth display screen), select one of the following: • • • • Off +6dB 0dB - 6dB Note: The default is 0dB. c. To enable (confirm) the selected setting, press the rotary control [ ]. Note: When Headphone Limit is set to anything but Off, a LIM indication will show up on the leftmost display.
5.2.2 Audio settings for the microphone To configure the audio settings for the microphone: 1. In Menu mode [ ], select Audio Settings and then Microphone. 2. To select the Headroom: a. From the third menu (third display screen), select Headroom. b. From the fourth menu (fourth display screen), select one of the following: • Normal • High - Reduces the analog input gain and increases the digital gain accordingly. That reduces digital clipping at the A/D converter but increases the noise floor.
5.2.4 Audio settings for Program IFB [Interruptible Foldback] IFB allows you to temporarily interrupt the continuous program listen (program feed) and speak to the channels connected to the program listen. See also 5.4.2 Assigning the Program Listen to a channel. To configure the audio settings for Program IFB [Interruptible Foldback]: 1. In Menu mode [ ], select Audio Settings and then Program IFB. 2. From the third menu (third display screen), select IFB Dim Level.
5.2.6 Audio settings for the Hot Mic Output To configure the audio settings for the Hot Mic Output: 1. In Menu mode [ ], select Audio Settings and then Hot Mic Ouput. 2. From the third menu (third display screen), select Gain. 3. From the fourth menu (fourth display screen), select one of the following: • • • • • + 12dB + 6dB 0dB - 6dB -12dB Note: The default is 0. 4. To enable (confirm) the selected setting, press the rotary control [ ]. 5.2.
5.3 Setting Station Settings 5.3.1 Setting Preferences To set the Preferences: 1. In Menu mode [ ], select Station Settings and then Preferences. 2. From the third menu (third display screen), select Station ID. Enter a station ID with a maximum of 10 alphanumeric characters: To enable (confirm) the selected setting, press the rotary control [ ]. 5.3.2 Setting Keyset Assignments To set the Keyset Assignments: 1. In Menu mode [ ], select Station Settings and then Keyset Assign. 2.
Important note: The RMK (Remote Mic Kill) key is also displayed in the list. This key cannot be latched. The RMK key is used to: • Send a message to all connected HelixNet Partyline devices to deselect any latched keyset Talk routes. • Turn off any latched Talk routes on connected analog partyline equipment. To find out how to enable or disable the RMK key, see 5.3.4 Setting the RMK (Remote Mic Kill) key. Tip: For a quick reference to the location of keys on the front panel, see 2.
5.3.5 Setting display screen brightness By default, the display screens are set for medium brightness. To set the brightness of the display screens: 5. In Menu mode [ ], select Station Settings and then Display. 6. From the third menu (third display screen), select OLED Brightness. 7. From the fourth menu (fourth display screen), select one of the following brightness settings: • • • High Medium Low Note: The default is Medium. 8. To enable (confirm) the selected setting, press the rotary control [ ].
5.3.7 Setting the screensaver The screensaver features the channel label and is enabled by default. The display screens enter screensaver mode when the main station has been inactive for 10 minutes. Tip: To exit screensaver mode, press any key on the front panel. To enable or disable the screensaver: 1. In Menu mode [ ], select Station Settings and then Display. 2. From the third menu (third display screen), select Screensaver. 3.
6. The character you have selected for editing is shown in a box with a dotted border [ ]. To display alternative characters in the box, turn the rotary control [ characters comprises the following: Characters Description / range Numbers (numeric) Letters 0 to 9 Symbols # & *() -_=+ /!@ : ]. The range of available Capital letters = A to Z Small letters = a to z Note: You can also select a space. Table 33: Channel label characters To select a character, press the rotary control [ ]. 7.
5.5 Configuring the Control I/O The Control I/O connector (25 way female D-type) on the rear panel allows you to connect up to 4 relay outputs or 4 opto inputs and control them through the main station keysets: I/O type Description Opto inputs Opto inputs enable you to connect a foot switch or other control device and use it to trigger Call or Talk functions.
5.5.2 Configuring Relay outputs To configure the Control I/O for Relay outputs: 1. In Menu mode [ ], select Control I/O. 2. From the second menu (second display screen), select Outputs. 3. From the third menu (third display screen), select one of the four available Relay outputs: • • • • Relay 1 Relay 2 Relay 3 Relay 4 4.
5.6.1 Configuring a Four-wire interface module The following procedure shows you how to configure the Module Settings for a Four-wire interface module. To configure the Module Settings for a four-wire interface module: 1. In Menu mode [ ], select Module Settings. 2.
5. To set the input level for the four-wire port: a. From the third menu (third display screen), select Input Gain. b. From the fourth menu (fourth display screen), select one of the following: • • • • • +12dB + 6dB. 0dB -6dB. -12dB Note: The default is 0dB. c. To enable (confirm) the selected setting, press the rotary control [ ]. 6. To set the output level for the four-wire port: a. From the third menu (third display screen), select Output Gain. b.
8. The VOX Delay OFF setting determines the length of time to wait before deactivating the incoming audio. To set the VOX Delay OFF setting: a. From the third menu (third display screen), select VOX Delay OFF. b. From the fourth menu (fourth display screen), select one of the following: • • • • • [0].5 sec. 1 sec. 2 sec. 3 sec. 4 sec Note: The default is [0].5 sec. c. To enable (confirm) the selected setting, press the rotary control [ ]. 5.6.
b. From the fourth menu (fourth display screen), select one of the following: • • • • • Disabled Channel A Channel B Channel C Channel D Note: The default is Disabled. Note: When linking is enabled, there will be more than four channels. To enable (confirm) the selected setting, press the rotary control [ ]. 3. To set the Program Output: a. From the third menu (third display screen), select Program Output. b.
Note: For detailed pinout information, see 2.2.1 HMS-4X Main Station rear panel: Interface modules. To configure the port for either Clear-Com or RTS systems: a. From the third menu (third display screen), select Mode. b. From the fourth menu (fourth display screen), select one of the following: • • • c. Clear-Com RTS Audio Pin 2 RTS Audio Pin 3 To enable (confirm) the selected setting, press the rotary control [ ]. 7. To set the Input Gain: a.
9. Enabling RMK [Remote Mic Kill] Input allows an external source (such as the main (base) station of the connected two-wire system to send an RMK signal to the analog beltpacks attached to the HelixNet main station. To enable RMK Input: a. From the third menu (third display screen), select RMK Input. b. From the fourth menu (fourth display screen), select one of the following: • • Enabled Disabled Note: The default is Disabled. c.
12. The VOX Delay OFF setting determines the length of time to wait before deactivating the incoming audio. To set the VOX Delay OFF setting: a. From the third menu (third display screen), select VOX Delay OFF. b. From the fourth menu (fourth display screen), select one of the following: • • • • • [0].5 sec. 1 sec. 2 sec. 3 sec. 4 sec Note: The default is [0].5 sec. c. To enable (confirm) the selected setting, press the rotary control [ ]. 5.6.
3. To enable or disable DHCP: a. In Menu mode [ ], select Networking. Note: The Networking menu only appears if an Ethernet or Fiber interface module is detected. b. From the second menu (second display option), select Preferences. c. From the third menu (third display option), select DHCP. d. From the fourth display screen, select one of the following: • Disabled • Enabled Note: The default is Enabled 4. To edit the IP address: a. In Menu mode [ ], select Networking.
5.6.4 Configuring the Module Settings: Version information The software (firmware) for the ports on the interface module must match that on the HelixNet Main Station itself. To check the software version for the Main Station and each port on the interface module: 1. In Menu mode [ ], select Administration > Software > Current. 2. In the fourth menu (display screen), use the rotary control [ versions. ] to scroll the displayed software 3.
5.7.2 Updating the software Important note: The following procedure is relevant to future software updates only. Customers will be contacted by email when software updates become available. Updates will be downloaded through a link provided in the email. Any HBP-2X beltpacks that are connected to the Main Station are automatically updated. The beltpacks remain non-functional for approximately 5 minutes while they are updated. You can also use a USB memory stick (USB 2.
5.7.3 Locking and unlocking the HBP-2X beltpack menus You can prevent beltpack users from changing the menu settings on connected HBP-2X beltpacks by locking the menus. Unlock the beltpack menus to allow users to change the beltpack menu settings. To lock (or unlock) the HBP-2X beltpack menus from the Main Station: 1. In Menu mode [ ], select Administration and then Beltpacks. 2. The third menu (display screen) displays a single, selected menu item: Menu Lock.
5.7.6 Saving and restoring the software settings. To save or restore the software settings: 1. In Menu mode [ ], select Administration and then Settings. 2. To save, in the third menu (display screen), select Save. Once you select Save you should not remove the USB stick right away. Depending on the USB stick it might take up to 5 seconds to complete. a. In the fourth menu (fourth display screen), select between saving to a USB or saving locally. 3.
5.8.2 Viewing temperature information To view the temperature of the Main Station: 2. In Menu mode [ ], select Diagnostics and then Hardware. 3. From the third menu (third display screen), select one of the following temperature sensors: • • • Sensor 1 Sensor 2 Sensor 3 The fourth menu (fourth display screen) displays the temperature, for example: +30°C Environmental note: The recommended operating temperature range for the HelixNet HMS-4X Main Station is 0 - +50°C.
3. The fourth menu (fourth display screen) displays the status and other measures / information for the powerline. The status of the powerline is either Ok [operating normally], Busy or Error. For more details of the information displayed, see Appendix B: Menu maps. Note: Powerline status is also indicated by the powerline LEDS on the front panel. Green LED = Ok Amber LED = Busy Red LED = Error For more information about powerline diagnostics, see Appendix D:Troubleshooting. 5.8.
6 Configuring and Managing the HBP-2X Beltpack This chapter describes how to configure the settings and manage the HBP-2X Beltpack using Menu mode. It also shows you how to monitor and diagnose performance issues, using the Diagnostics menus. Tip: For a quick reference to the Main Station menus, see Appendix B: Menu maps. 6.1 Using the Menus To place the Main Station in Menu mode, press the Menu key [ ] on the top of the beltpack.
2. The final level of menu (the second or third display screen) displays the settings that relate to your previous menu choices (system features or functionality). The current setting is indicated by a dotted box [ ] around the menu item When you have selected a setting, press the right-hand Call key [ the Main Station. ] to enable the setting on 6.1.2 Exiting Menu mode To exit Menu mode on the beltpack, do either of the following: • Press the Menu key [ • Wait until Menu mode times out.
4. To limit the peaks in audio on the headphones (or to disable headphone limiting): a. Select Headphone Limit. b. Select one of the following: • • • • Off +6dB 0dB - 6dB Note: The default is 0dB. c. To enable (confirm) the selected setting, press the right-hand Call key [ ]. Note: Limiting peaks in audio can help to prevent distortion on the headphone mic. Note: When Headphone Limit is set to anything except Off, a LIM indication will show up at the top right of the display 5.
6.3 Audio settings for the microphone To configure the audio settings for the microphone: 4. In Menu mode [ ], select Audio Settings and then Microphone. 5. To select the Headroom: c. From the third menu (third display screen), select Headroom. d. From the fourth menu (fourth display screen), select one of the following: • Normal • High Note: The default is Normal. 6. To enable or disable the Contour Filter: a. From the third menu (third display screen), select Contour Filter b.
6.4.1 Assigning channels You can assign any two of the four available channels to the beltpack (including the same channel to both keysets). To assign a channel to the left-hand keyset (set of controls): 1. In Beltpack Settings select Left Channel. 2. Select one of the four available channels (or none): • • • • • None. Channel A Channel B Channel C Channel D Note: More that four channels will be available when Main Stations are linked. Note: The default channel labels (names) are shown above.
6.4.2 Setting Talk key latching To enable (or disable) Talk key [ ] latching: 1. In Beltpack Settings select Talk Latch. 2. Select one of the following: • • Latching Non-Latching Note: The default is Latching. The setting is global (it applies to both channels on the beltpack). 3. To enable (confirm) the selected setting, press the right-hand Call key [ ]. 6.4.3 Setting the beltpack to vibrate when called To enable (or disable) vibration when a Call signal is received: 1.
6.5.1 Setting display screen brightness By default, the display screen is set to medium brightness. To set the brightness of the display screen: 1. In Menu mode [ ], press the left-hand Call Key and then select Display Settings. 2. Select OLED Brightness. 3. Select one of the following: • • • High Medium Low Note: The default is Medium. 4. To enable (confirm) the selected setting, press the right-hand Call key [ ]. 6.5.
6.5.3 Setting the screensaver The screensaver is displayed onscreen after 10 minutes of inactivity on the beltpack. To enable (or disable) the screensaver: 1. In Menu mode [ ], press the left-hand Call Key and then select Display Settings. 2. Select Screensaver. 3. Select one of the following: • • Enabled Disabled Note: The default is Enabled. 4. To enable (confirm) the selected setting, press the right-hand Call key [ ]. 6.
3. The current version of the software is displayed. The software version information will appear similar to the following example: npl-x.x.xx.xxxx, uboot Where x is a numerical value. 6.6.2 Resetting the beltpack to default (factory mode) settings To reset the beltpack to default (factory mode) settings: 1. In Menu mode [ ], press the left-hand Call Key and then select Administration. 2. Select Reset to Default. 3. Reset Now is displayed (shown as selected).
7 Using the HMS-4X Main Station This chapter describes how to use the HMS-4X Main Station, after your HelixNet Partyline system has been installed and configured. For more information about integrating and using HelixNet Partyline with your existing intercom infrastructure, see 3 Installing HelixNet Partyline. Tip: For a quick reference to the functionality of the HMS-4X Main Station, the optional interface modules and the HBP-2X Beltpack, see 2 User Interfaces. 7.
2. Adjust the volume of the Program Feed in relation to the overall volume level by turning the auxiliary loudspeaker rotary control [Prog] [ ], located to the right of the loudspeaker. The Prog volume control is subordinate to the Main volume control. To increase the volume level, turn the rotary control(s) [ ] clockwise. To decrease the volume level, turn the rotary control(s) [ ] anti-clockwise.
3. To adjust the volume level of incoming audio to the headset: a. Adjust the volume of all incoming audio by turning the loudspeaker rotary control [Main] [ ]. The control is located to the left of the loudspeaker. b. Adjust the volume of the Program Feed in relation to the overall volume level by turning the auxiliary loudspeaker rotary control [Prog] [ ]. The control is located to the right of the loudspeaker. The Prog volume control is subordinate to the Main volume control. 7.1.
7.3 Using the channel keysets A keyset (set of controls) is located next to each of the four display screens. In operating mode, each keyset is dedicated to the control of one of the four supported intercom channels. The standard onscreen information for each channel comprises: • The channel label (name) [ • The volume level [ ]. ]. Notes: To change (edit) the channel label (name), see 5.4.1 Editing the channel label.
7.4 Using the All Talk key To talk to all connected intercom users, devices and systems, excluding the SA (Stage Announce) facility: 1. Press the All Talk key [ ] to the right of the fourth (last) display screen. Talk keys [ ] for all channels are activated automatically. When the mic (gooseneck or headset) is live, the Mic On key [ automatically. ] is also activated 2. Speak into the headset or gooseneck mic (see also 7.1 Using the gooseneck mic, loudspeaker and headset ). 7.
8 Using the HBP-2X Beltpack This chapter describes how to use the HBP-2X Beltpack, after your HelixNet Partyline system has been installed and configured. For more information about integrating and using HelixNet Partyline with your existing intercom infrastructure, see 9 Connecting to Other Intercom Systems. Tip: For a quick reference to the functionality of the HBP-2X Beltpack, the HMS-4X Main Station, and the optional interface modules, see 2 User Interfaces. 8.
To talk to the all the devices (beltpacks and Main Station) connected to the channel: 1. Connect a headset [ ], using the 4-pin XLR–M connector on the base / rear of the beltpack. Note: E in For the location of the headset connector and the headset key, see Table 22: Key to HBP-2X Beltpack connectors and controls ( base view). 2. Press the Talk key [ ]. 3. Speak into the headset mic. To adjust the volume of incoming audio for a channel, turn the appropriate side-mounted rotary control [ ].
9 Connecting to Other Intercom Systems This chapter provides basic guidance on connecting your HelixNet Partyline system to a range of other intercom systems, including: • Two-wire cabled partyline systems (RTS and Clear-Com Encore). • Two-wire / four-wire wireless systems (Tempest, CellCom / FreeSpeak, and the DX210). • Digital matrix systems (Eclipse MVX four-wire). The HMX-4X Main Station is connected to these systems using the optional Two-wire and Four-wire interface modules.
9.1.
9.1.3 Connecting to an Encore Main Station Note: The following procedure assumes that a two-wire interface module has been fitted to the HMS-4X Main Station. For more information about interface modules, see 2.2.1 HMS-4X Main Station rear panel: Interface modules. Note: A HelixNet system with HLI-2W2 must be able to receive power from an analog power line. To connect your HelixNet Partyline system to an Encore Main Station (for example, the four channel MS704): 1.
3. On the Encore (MS-704) Main Station, adjust nulling for the selected channel (either channel A, B, C or D on the MS-704). Nulling helps to reduce echo while talking on a two-wire audio system. Tip: The amount of null that is required changes when you add or remove devices, or alter the length of the cabling. For optimum performance, Clear-Com recommends that you adjust the nulling every time you make a change to the system configuration.
9.2.
9.2.3 Connecting to an RTS (Telex) intercom station To connect your HelixNet Partyline system to an RTS intercom station (in this case, the 2 channel MCE325 user station): 1. On the HMS-4X Main Station, configure the Module Settings for the two-wire interface module. For the full procedure, see 5.6.2 Configuring a Two-wire interface module. Ensure that you: • Configure port(s) for RTS systems.
3. On the RTS device (in this case, the MCE325), adjust the nulling (if necessary) on the channel to which the HMS-4X Main Station is connected. Nulling helps to reduce echo while talking on a two-wire audio system. A sidetone nulling trimmer (control) is provided for each of the four channels on the device. To adjust a sidetone nulling trimmer: a. Turn the speaker switch on (even if an external speaker is not connected).
9.3.
9.3.3 Two-wire connection to Tempest To connect your HelixNet Partyline system to Tempest, using a two-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the two-wire interface module. For the full procedure, see 5.6.2 Configuring a Two-wire interface module. Note: Check that the Two-wire module is configured for Clear-Com systems (the default) and enable Auto-nulling. Auto-nulling helps to reduce echo while talking on a two-wire audio system. 2.
3. Physically connect the HelixNet Partyline and Tempest systems. Powering the connection: You must power the connection between the systems using either a dedicated power supply (such as the PK-7, PS-702, or PS-704), or a powered Encore Main Station (such as the MS-702 or MS-704). Tip: For more information about the dPK-7 or PS-70x power supply devices from Clear-Com, see http://www.clearcom.
9.3.
9.3.5 Four-wire connection with Tempest To connect your HelixNet Partyline system with Tempest, using a four-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the Four-wire interface module. For the procedure, see 5.6.1 Configuring a Four-wire interface module. 2. On the Tempest BaseStation, configure an intercom channel for four-wire connection: d. Select the intercom channel (A or B), using the CHAN selection button [ ] on the front panel. e.
9.4 Connecting HelixNet Partyline to CellCom / FreeSpeak 9.4.1 About CellCom / FreeSpeak CellCom / FreeSpeak is a wireless intercom system from Clear-Com, operating within the license-free 1.92-1.93GHz frequency band. The system is branded as CellCom in North America and as FreeSpeak in the rest of the world. CellCom /FreeSpeak combines DECT and wireless auto-roaming technologies to allow users to move freely without losing communication connection.
9.4.2 Quick reference: Two-wire connection to CellCom / FreeSpeak Two-wire connection to CellCom / FreeSpeak Standard mic cable / CAT-5 3-pin XLR connectors 2W HMS-4X Main Station CellCom / FreeSpeak Basestation Power supply Configure the 2W module Configure the port as Clear-Com Enable auto-nulling Or Encore Main Station (MS-70x) Connect to CH-A or CH-B connectors Enable CH-A or CH-B.
9.4.3 Two-wire connection to CellCom / FreeSpeak To connect your HelixNet Partyline system to a CellCom / FreeSpeak basestation (Main Station), using a two-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the two-wire interface module. For the procedure, see 5.6.2 Configuring a Two-wire interface module. Note: Check that the two-wire module is configured for Clear-Com systems (the default) and enable Auto-nulling.
9.4.
9.4.5 Four-wire connection to CellCom / FreeSpeak To connect your HelixNet Partyline system with a CellCom / FreeSpeak basestation (Main Station), using a four-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the four-wire interface module. For the procedure, see 5.6.1 Configuring a Four-wire interface module. 2. Connect the HMS-4X Main Station and the CellCom / FreeSpeak basestation, using four-wire crossover CAT5 cabling.
9.5.2 Quick reference: Two-wire connection to DX210 Two-wire connection to DX210 Standard microphone cable 3-pin XLR connectors HMS-4X Main Station Configure the 2W module Configure the port as Clear-Com Enable auto-nulling 2W DX210 Basestation (BS210) Power supply Or Encore Main Station (MS-70x) Line must be powered (HMS-4X 2W module appears as unpowered beltpack / Communicator to DX210).
9.5.3 Two-wire connection to the DX210 To connect your HelixNet Party-line system to the DX210 basestation (Main Station), using a two-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the Two-wire interface module. For the procedure, see 5.6.2 Configuring a Two-wire interface module. Note: Check that the two-wire module is configured for Clear-Com systems (the default) and enable Auto-nulling. Auto-nulling helps to reduce echo while talking on a two-wire audio system. 2.
5. Apply auto-nulling to the connected channel (either IC1 or IC2) on the DX210 basestation. Autonulling helps to reduce echo while talking on a two-wire audio system. To apply auto-nulling: a. Insert a pen or similar pointed object into the AUTO-NULL hole on the front panel. b. Press and hold AUTO-NULL for 2 seconds. Note: Before applying auto-nulling, ensure that there are no open microphones on the wired intercom.
9.5.
9.5.5 Four-wire connection to the DX210 To connect your HelixNet Partyline system with a DX210 basestation (BS210), using a four-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the Four-wire interface module. For the procedure, see 5.6.1 Configuring a Four-wire interface module. 2. Connect the HMS-4X Main Station and the DX210 basestation (BS210), using four-wire crossover CAT5 cabling.
9.6 Connecting HelixNet Party-line to Eclipse 9.6.1 About Eclipse Eclipse is the digital matrix system from Clear-Com. A wide choice of system frames, system cards and modules enables the unification of multiple intercoms systems (digital, analog, wired and wireless) in a single intercoms infrastructure. Eclipse is configured, managed and maintained using the intuitive Eclipse Configuration Software (ECS).
9.6.
9.6.3 Two-wire connection to an Eclipse Median system frame To connect your HelixNet Party-line system to an Eclipse Median, using a two-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the Two-wire interface module. For the procedure, see 5.6.2 Configuring a Two-wire interface module. Note: Check that the two-wire module is configured for Clear-Com systems (the default) and enable Auto-nulling. Auto-nulling helps to reduce echo while talking on a two-wire audio system. 2.
3. Apply nulling to the connected channel on the CCI-22. To null the channel: a. Insert the accessory earphone into the front-panel Test jack. A test tone, for all frequencies, is produced every 0.5s. b. While listening to the test tone, adjust the R (Resistance) control until the tone is at a minimum. c. Repeat Step b. for the L (Inductance) and C (Capacitance) controls. These controls compensate for each component of the line’s impedance, providing the best possible null.
9.6.
9.6.5 Four-wire connection to Eclipse To connect your HelixNet Partyline system to an Eclipse Median, using a four-wire connection: 1. On the HMS-4X Main Station, configure the Module Settings for the four-wire interface module For the procedure, see 5.6.1 Configuring a Four-wire interface module. 2. Connect the HMS-4X Main Station directly to the MVX-A16 card (the 16 port audio and data card set) with standard CAT5 cable.
10 Specifications 10.1 Main Station (HMS-4X) 10.1.1 Connectors Specification Description / value Intercom Powerline Outputs (4) 3-pin XLR–M Headset 4-pin XLR–M USB USB Type A and Micro-AB Program 3-pin XLR–F SA (Stage Announce) 3-pin XLR–M Hot Mic / IFB Interface 1/4 in. (0.64 cm) phone jack GPI 25 way D-type female Table 40: Main Station: Connectors 10.1.2 Microphone pre-amplifier Specification Description / value Headset Mic impedance: 200 Ω (Dynamic) Headset Mic Voltage 1.
10.1.3 Headphone amplifier Specification Description / value Load impedance 32 Ω Output level +12dBu before clipping Sidetone -12dB (selectable) The following specified for a route from a 4-wire output @ 0dBu in Max gain 0dB Frequency response 40 Hz - 10 kHz ±3dB Distortion <0.1% THD @ 1 kHz Noise <-65dBu Headphone limiter 0dBu (selectable) Table 42: Main Station: Headphone amplifier 10.1.
10.1.5 Program line input and Four-wire option module inputs Specification Description / value Maximum level before clipping 18 dBu Nominal input level 0dBu(selectable) Input impedance >= 10 KΩ The following specified for a route to 4-wire output @ 0dBu out Frequency response 20 Hz - 10 kHz ±3dB Distortion <0.2% THD @ 1 kHz Noise <-65dBu Table 44: Main Station: Program line input and four-wire option module inputs 10.1.
10.1.8 Hot Mic output Specification Description / value Maximum level before clipping 12 dBu Nominal output level 0dBu(selectable) Output impedance <= 100Ω The following specified for a route from a dynamic headset Frequency response 300 Hz - 12 kHz ±2dB Distortion <0.
10.1.9 Helix Digital Partyline Specification Description / value Maximum level before clipping 6 dBu Nominal input level -18dBu (C-C) -12dBu (RTS) Input impedance >= 10KΩ bridging The following specified for a circuit to a 4-wire input @0dBu in: Frequency response 100Hz - 10 kHz ±3dB Distortion <0.2% THD @ 1 kHz Noise <-55dBu The following specified for a circuit from a 4-wire output @0dBu out: Frequency response 40 Hz - 10 kHz ±3dB Distortion <0.
10.1.11 Mains power Specification Description / value Input Voltage range 100 – 240 VAC Input frequency range 50 – 60 Hz Input power <=250 VAC Powerline Intercom Output Voltage + / - 30 VDC ± 1V Output current per channel -1.5A (continuous) Table 50: Main Station: Mains power 10.1.12 Environmental Specification Description / value Temperature 0˚C - 50˚C (32˚F - 158˚F) Humidity 0 - 90% relative humidity Table 51: Main Station: Environmental 10.1.
10.2 Two-wire module: general 10.2.1 Connectors Specification Description / value Intercom line (2) 3-Pin XLR-F Table 53: two-wire module: Connectors 10.2.2 Dimensions and weight Specification Description / value Dimensions 7.05 in. H x 2.24 in. W x 1.54 in. D (179 x 57 x39 mm) Weight 13 oz. (0.35 kg) Table 54: Two-wire module: Dimensions and weight 10.2.3 Power requirements (external) Specification Description / value Per channel 0.
10.3 Four-wire module: general 10.3.1 Connectors Specification Description / value Intercom line (2) RJ-45 (Ethercon) Table 57: Four-wire module: Connectors 10.3.2 Dimensions and weight Specification Description / value Dimensions 7.05 in. H x 2.24 in. W x 1.54 in. D (179 x 57 x39 mm) Weight 13 oz. (0.35 kg) Table 58: four-wire module: Dimensions and weight 10.3.
10.4 Beltpack (HBP-2X) 10.4.1 Connectors Specification Description / value Intercom line (2) 3-pin XLR–M-F Headset 4-pin XLR–M and 2.5mm TRS jack USB Micro-AB Table 60: Beltpack: Connectors 10.4.2 Microphone pre-amplifier Specification Description / value Headset Mic impedance: 200 Ω (Dynamic) Headset Mic Voltage 1.
10.4.3 Headphone amplifier Specification Description / value Load impedance >32 Ω Output level +12dBu before clipping Sidetone -12dB (selectable) The following specified for a route from a 4-wire input @0dBu in: Max gain 0dB Frequency response 40 Hz - 10 kHz ±3dB Distortion <0.1% THD @ 1 kHz Noise <-65dBu (@ max gain) Headphone limiter -0dBu (selectable) Table 62: Beltpack: Headphone amplifier 10.4.
Appendix A: Compliance FCC notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
Waste Electrical And Electronic Equipment (WEEE) The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturers, distributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE Directive covers most Clear-Com products being sold into the EU as of August 13, 2005.
Appendix B: Menu maps HMS-4X Main Station menu map Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Audio Settings Headset Sidetone Gain Range: 0dB - -18dB Default: -12db Headphone Limit Off + Range: +6dB - -6dB Default: 0db Sidetone Control Tracking Non-Tracking Disabled Default: Tracking HS Mic Type Electret Dynamic (0 dB) Dynamic (-10 dB) Default: Dynamic (0 dB) Microphone Headroom Normal High Default: Normal Contour Filter Enabled Disabled Default: Enabled 127 HelixNet Partyline User
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Program Input Gain Range: +12dB - -12dB Default: 0db Program IFB IFB Dim Level IFB Disabled + Range: -6dB - -24dB + Full Cut SA Output Gain Range: +12dB - -12dB Hot Mic Output Front Panel Default: 0db Loudspeaker Dim Range: 0dB - -24dB Default: -6dB 128 HelixNet Partyline User Guide
Menu 1 (First) > Menu 2 > Menu 3> Station Settings Preferences Station ID Keyset Assign Keyset 1 – 4 Menu 4 (Last ) Alphanumeric entry None [conf_name_1], [conf_name_2] …..
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Channels Channel A Label Press to Edit Channel B Channel C Max.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Output Gain Default: 0db VOX Enabled Disabled Default: Disabled VOX Off Delay Range: [0].5 – 4 secs Default: [0].
Menu 1 (First) > Menu 2 > Menu 3> RMK Outpu Menu 4 (Last ) Disabled Default: Enabled VOX Enabled Disabled Default: Disabled VOX Off Delay Range: [0].5 – 4 secs Default: [0].
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Network Stations [Station IDs} Separate Linked IP address: xx.xx.xx.xx where x is a numeric value Linking Link Station Disabled Enabled Default: Disabled Preferences DHCP Enabled Disabled Default: Enabled Administration IP Address IP address: xx.xx.xx.xx where x is a numeric value Gateway IP address: xx.xx.xx.xx where x is a numeric value Subnet Mask IP address: xx.xx.xx.
Menu 1 (First) > Menu 2 > Menu 3> Menu 4 (Last ) Diagnostics Hardware Main PCB Part: [Part_Number] Revision: [Revision] Serial number: [Serial number] Slot 1 PCB Slot 2 PCB Slot 3 PCB Temperature Sensor 1 Temperature in °C. Sensor 2 Note: Single fan on if any sensor > 60°C. Double fan on if any sensor > 65°C. Double fan off if < 55°C / single fan off if < 50°C.
HBP-2X Beltpack menu map Menu 1 (First) > Menu 2> Menu 3 (Last ) Audio Settings Sidetone Gain Range: 0dB - -18dB Default: -12dB Headphone Limit Off + Range: +6 - -12dB Default: 0dB Sidetone Control Tracking Non-tracking Disabled Default: Tracking HS Mic Type Electret (-15dB) Dynamic (0dB) Dynamic (-10dB) Default: Dynamic (0dB) Note: Electret = 35dB fixed gain, non-user adjustable. Dynamic = 50dB fixed gain, non-user adjustable.
Menu 1 (First) > Menu 2> Menu 3 (Last ) Beltpack Settings Left Channel None Channel A Channel B Channel C Channel D Right Channel Talk Latch Latching Non-Latching Default: Latching Vibrate On Call On Off Default: Off Display Settings OLED Brightness High Medium Low Default: Medium Key Brightness High / Low High / Off Low / Off Off / Off Default: High / Low Rotate Display Enabled Disabled Default: Disabled Screensaver Enabled Disabled Default: Enabled 136 HelixNet Partyline User Guide
Menu 1 (First) > Menu 2> Menu 3 (Last ) Administration IP Address IP address: xx.xx.xx.xx where x is a numeric value Software Version npl-1.0.x, uboot Software Update npl-1.0.x Reset to Default Reset Now Hardware Main PCB Diagnostics Important Note: There are 4 levels of Menu for Hardware Powerline Note: Line (partyline) that connects beltpack to the network (and which also powers the beltpack).
Appendix C: Cabling reference You can connect HBP-2X Beltpacks to the HMS-4X Main Station using: • • A wide range of standard microphone (intercom) cable types (16 AWG – 26 AWG). CAT5, CAT5e and CAT6 cable types. Note: Clear-Com recommends the use of shielded twisted pair cabling. You can also mix CAT cables and microphone cables when connecting to the HMS-4X Main Station.
Quick reference: Cable capacity versus distance 410 492 574 656 738 820 902 984 1066 1230 1394 1558 1722 1886 2050 2214 2378 1148 1312 1476 1640 1804 1968 2132 2296 Max Distance (Meters) (Feet) *All cables, including Category cables, must be shielded for optimum performance Figure 28: Cable capacity versus distance Note: The above graph is intended as a general guide only. Actual cable performance may vary, depending on the conditions and complexity of the installation.
Appendix D: Troubleshooting Issue Solution Why are the Talk keys flashing periodically? Flashing Talk keys may indicate a fault in the cable. Check the cable for short-circuit conditions and replace if necessary. The Call functionality on my analog beltpack is no longer working. HelixNet Partyline operates at different voltage levels than analog two-wire partyline systems. The analog beltpack may have been damaged if it was connected to a HelixNet Main Station partyline port.
Line 1 (or Line 2) LED is steady red and one or more Beltpack has no bars showing up for signal strength. There are digital errors or there is cross-talk on that Powerline. Look at the Diagnostics->Powerlines->Powerline 1(or 2) page. If the number of Beltpacks showing there does not match what you physically connected to that Powerline, cross-talk is happening between the Powerlines. Make sure you are using properly shielded Mic cables or Cat cables.