Owner's manual

ManualsBrandsClear-Com ManualsAccessories communicationHME DX200

HM ELECTRONICS, INC. 14110 Stowe Drive, Poway, CA 92064 USA • Phone: 1-800-848-4468 Fax: (858) 552-0172

HME# 400G612

Rev B 7/3/08

WS200

Wireless Speaker Station

OPERATING INSTRUCTIONS

The WS200 Speaker Station can be used with a DX100 or DX200 system, together with Beltpacs and WH200

All-in-one Headsets. It provides wireless communication through its built-in microphone and speaker or a plug-in

headset. A remote speaker can also be connected to the unit. The Speaker Station can be used on a table top or

mounted on the wall. It can be operated with standard AC power, 12-14VDC or with six AA batteries or an optional

rechargeable battery. A power supply with cord and a battery sled are provided.

SETUP

Wall Mounting

If you choose to mount the WS200 on the wall and if AC operation is required, it must be mounted close enough to an

electrical outlet to be reached with the power supply and cord.

• Hold the unit against the wall where you will mount it and

mark the wall through the four holes in the flanges on its left

and right sides.

• Drill holes in the wall at the four marked spots, and mount

the WS200 over the holes with your

selected hardware (not provided).

Summary of content (9 pages)

PAGE 1
WS200 Wireless Speaker Station OPERATING INSTRUCTIONS The WS200 Speaker Station can be used with a DX100 or DX200 system, together with Beltpacs and WH200 All-in-one Headsets. It provides wireless communication through its built-in microphone and speaker or a plug-in headset. A remote speaker can also be connected to the unit. The Speaker Station can be used on a table top or mounted on the wall.
PAGE 2
Power Setup AC Power Operation If using the WS200 with AC power ⎯ • Plug the connector at the end of the power supply cord into the 12-14 VDC power connector on right side of the unit. Turn the sleeve on the connector clockwise to secure it to the unit. • Plug the large female connector at one end of the AC power cord into the power supply. Plug the other end of the AC power cord into an electrical outlet.
PAGE 3
WS200 Registration The first time you operate the WS200, you must register it for use with a specific DX100 or DX200 Base Station. The base station will then recognize the WS200 when its power is on, and will be able to tell the difference between it and other electronic equipment operating on similar frequencies, or DX family Beltpacs or All-in-one Headsets. NOTE: The WS200 must be within 6 feet (1.83 meters) of the base station while being registered.
PAGE 4
If registration failed: • A voice message will say “Power on, Speaker, Version #, Begin registration, …” The ISO and IC lights on the WS200 will be blinking red, and there may be a delay of up to 90 seconds before you hear “Registration failed.” • Press the RESET button on the base station. When the REGISTRATION STATUS display becomes blank, press the REG / REGISTER BELTPAC button on the base station and register the WS200 again. If registration fails again, call your dealer for assistance.
PAGE 5
OPERATION Headset connector Headset Connection If you are using a headset with the WS200, plug it into the headset connector. When using a headset, if the red light over the SPEAKER button is on, incoming communication can be heard through the headset and the speaker. If the red light over the SPEAKER button is off, incoming communication can only be heard through the headset. Push-To-Talk (PTT) or Hands-Free (HF) Mode Setting • Be sure the WS200 power is off.
PAGE 6
Routine Operation Power On/Off • To turn WS200 power on, press and release the POWER button. — Red lights will go on over the POWER, ISO and IC buttons. — If listening with a headset, or the speaker is turned on, you will hear “Power on, Speaker #, Version #.” — The light over the ISO button will go off. — The light over the IC button will change to green. • To turn WS200 power off, press and hold the POWER button for 2 seconds.
PAGE 7
Headset Microphone Gain Adjustment Some users speak louder or softer than others. The headset microphone gain adjustment helps to compensate for these differences, raising or lowering the voice level of the user speaking into the microphone. Increase microphone gain for softer voices, decrease for louder voices. • To adjust microphone gain, first be sure the internal speaker is off. • Press and hold the ISO button while pressing the VOLUME up ▲ or down ▼ arrow.
PAGE 8
EQUIPMENT SPECIFICATIONS Frequency Range: 2400 – 2483.5 MHz Frequency Response: 200 Hz to 3.5 kHz Power Requirements: Six AA batteries (NiMH optional), 12-14VDC or 100-240VAC, 50-60Hz Temperature Range: -4 to 131°F (-20 to 55°C) typical Size: 9.38” x 5.16” x 3.34” (23.83 x 13.11 x 8.48 cm) Weight: 2.56 lb with battery (1.16 kg) Headset Connector: 4-Pin Mini-DIN Microphone: Electret Speaker: 1.
PAGE 9
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules.