User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications
2.3 COMMUNICATOR
®
Setup and Registration 2.3 COMMUNICATOR
The first time you operate the DX210 system, you must register each Communicator (Belt Pack and/or
All-In-One Headset) for use with a specific base station. The base station will then recognize all
registered Communicators when their power is on, and will know the difference between them and other
electronic equipment operating on the same frequencies. If a Communicator is added or replaced later,
the new one must be registered and the old one remains in memory. A maximum of 15 Communicators
can be registered to a single base station at one time.
The first time you operate the DX210 system, you must register each Communicator (Belt Pack and/or
All-In-One Headset) for use with a specific base station. The base station will then recognize all
registered Communicators when their power is on, and will know the difference between them and other
electronic equipment operating on the same frequencies. If a Communicator is added or replaced later,
the new one must be registered and the old one remains in memory. A maximum of 15 Communicators
can be registered to a single base station at one time.
2.3.1 Set Up COMMUNICATOR
®
s 2.3.1 Set Up COMMUNICATOR
NOTE: If multiple base stations will be used, or if interference is present, such as Wi-Fi interference,
refer to
Base Station Registration and Interference Avoidance, in Appendix D and E, pages 23 and 25.
Before registering them, set up all Communicators as follows: Before registering them, set up all Communicators as follows:
Belt Packs Belt Packs
1 1
2 2
3 3
Power
button
Power
button
1 - Insert a fully charged battery
in each Belt Pack, with the
metal contacts on the end of
the battery inserted first.
Press it in until it snaps.
1 - Insert a fully charged battery
in each Belt Pack, with the
metal contacts on the end of
the battery inserted first.
Press it in until it snaps.
2 - Place each Belt Pack
in a pouch.
2 - Place each Belt Pack
in a pouch.
3 - Plug its headset cable
connector into each Belt Pack.
3 - Plug its headset cable
connector into each Belt Pack.
All-In-One Headsets All-In-One Headsets
Insert a fully charged battery in each Headset,
with the metal contacts on the end of the battery
inserted first. Press it in until it snaps.
Insert a fully charged battery in each Headset,
with the metal contacts on the end of the battery
inserted first. Press it in until it snaps.
7
Clear-Com HME DX210 System Guide
®
Setup and Registration
®
s
NOTE: If multiple base stations will be used, or if interference is present, such as Wi-Fi interference,
refer to
Base Station Registration and Interference Avoidance, in Appendix D and E, pages 23 and 25.
Power
button
7
Clear-Com HME DX210 System Guide