User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications
2.3.2 Register COMMUNICATOR
®
s
The Communicator must be within 6 feet (1.83 meters) of the base station to enable registration.
1.
Be sure each Communicator you are going to register is turned off and the base station power
is on before you begin. Communicators that are already registered can be on or off.
2. Put the headset on your head.
3. Press the REG button on the front panel of the base station. The STATUS display will show a small
“o” for open.
STATUS display
“o”
REG button
NOTE: If you wait too long before going on to the next step, the base station will go out of the
registration mode and you will have to press the REG button again.
4. Press and hold the ISO button on the Communicator while you press and release the PWR (power)
button to turn the unit on, then release the ISO button. This will cause the Communicator to enter the
registration mode.
On Belt Packs, the two power lights at the corners near the IC1 and IC2 buttons will begin blinking
red, then will blink
g
reen two or three times and
g
o off. Wait! There ma
y
be a short dela
y
.
On All-In-One Headsets, the power/mode lights at the end of the microphone boom and on the
side of the unit near the IC1 button will blink. Wait! There may be a short delay.
If registration is successfully completed:
A voice message in the headset will say “Power on, Belt Pack #, Version #, Begin registration,
Registration complete, …”
After a delay of about 15 seconds, the STATUS display will show the ID number assigned to this
Communicator for about 10 seconds.
NOTE: ID numbers are assigned sequentially as 0 thru 9, A, b, C, d and E.
The power light on the Communicator will remain on steady green.
Re
p
eat Ste
p
s 2 to 4 above for each Communicator to be re
g
istered.
If registration failed:
A voice message in the headset will say “Power on, Belt Pack #, Version #, Begin registration, …”
Both lights on the Belt Pack will be blinking red, and there may be a delay of up to 90 seconds before
you hear “Registration failed.”
Press the RESET button at the lower-left corner of the base station with a pen or similar pointed
object. When the STATUS display becomes blank, press the REG button and register the
Communicator again. If registration fails again, call your dealer for assistance.
8
Clear-Com HME DX210 System Guide