User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications
If you try to register more than 15 Communicators:
An F will appear on the STATUS display on the base station and you will hear “Registration failed” in
the headset.
Clear all current registrations by pressing the CLR/BND button and the RESET button at the same
time. To press the RESET button, insert a pen or similar pointed object into the RESET hole at the
lower-left corner of the base station front panel. Continue holding the CLR/BND button after you
release the RESET button, until the clear code “c” (lower case) appears on the STATUS display.
Register all active Communicators, one at a time. Previously registered Communicators must be
re-registered.
2.3.3 COMMUNICATOR
®
Settings
If you want to set up a Communicator with any of the special settings shown below, press and hold the
specified button combinations during or after power up. These settings will remain in memory when the
Communicators are turned off and on again.
For Setting Press & Hold while you Press & Release the Power button
ISO restrict on
IC1 button
ISO restrict off
IC1 ISO and buttons
Handsfree on selected button(s)
IC1 and/or IC2 ISO and and/or volume up buttons
Handsfree off selected button(s)
IC1 and/or IC2 and/or ISO and volume down buttons
Listen-Only mode on volume down button
Listen-Only mode off volume up button
WH210 only *
All-In-One Headset “lights-off” mode
IC2 button
* NOTE: All-In-One Headsets can be set up with its indicator lights off, to avoid distraction if users are in an area
visible to audience. This setting is not saved when you power off.
For Setting With the power already on - - -
Increase mic gain (15 steps)
Press IC2 while you repeatedly press the volume up button
Decrease mic gain (15 steps)
Press IC2 while you repeatedly press the volume down button
BP210 only *
Increase sidetone level (5 steps)
Press IC1 while you repeatedly press the volume up button
BP210 only *
Decrease sidetone level (5 steps)
Press IC1 while you repeatedly press the volume down button
* NOTE: There is no sidetone adjustment function for All-In-One Headsets.
Power
button
NOTE: If you are not connecting a wired intercom, go on to
System Operation, section 3, page 13.
9
Clear-Com HME DX210 System Guide