User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications
5 Technical Data
5.1 BS210 Base Station Specifications
GENERAL
Channels:
2 audio channels
Frequency Range:
2400 – 2483.5 MHz
Frequency Response:
200 Hz to 3.5 kHz
Power Requirements:
100-240VAC, 50-60Hz or 12-14VDC
Temperature Range:
32-122°F (0-50°C)
Size:
19” x 1.72” x 17.13” (1-RU) (48.26 x 4.37 x 43.51 cm)
Weight:
9.0 lbs. (4.1 kg) maximum
# of COMMUNICATOR
®
s
per Base:
15 can be registered.
In single-channel operation, 4 can have simultaneous full-duplex communication.
In dual-channel operation, 3 can have simultaneous full-duplex communication.
4-Wire I/O:
RJ45, 600 balanced, level adjustable, simultaneous operation with 2-wire
2-Wire I/O:
XLR-3M, XLR-3F, externally-switchable RTS
®
or Clear-Com
®
mode,
200, level adjustable, null adjustable to 50dB attentuation, typical
Auxiliary Input:
XLR-3F/¼” (6.35 mm) combo jack, 600 balanced, level adjustable
Auxiliary Output:
XLR-3M, 600 balanced, level adjustable
Headset Connector:
4-pin mini-DIN, Electret microphone
Headset Output:
200mW into 32
Antenna Type:
External ½ -wave dipole (R-TNC connector), RX/TX horizontal/vertical diversity
System Distortion:
<2%
Communication Security:
64-bit encryption, dual-slot diversity
BASE STATION TRANSMITTER
Type:
Frequency Hopping, Spread Spectrum (FHSS)
Transmit Power:
100mW burst
Modulation Type:
Gaussian filtered FSK, TDMA
Frequency Stability:
13 ppm
Harmonics/Spurious:
Exceeds FCC and ETSI specifications over temperature
BASE STATION RECEIVER
Type: RF Sensitivity:
Frequency Hopping, Spread Spectrum <-90dBm w 10-3 BER
Frequency Stability:
13 ppm
Distortion:
<2%
17
Clear-Com HME DX210 System Guide