User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications
Appendix D: Multiple Base Station Registration
For multiple base stations to operate in close proximity without interference, they must all be properly
registered before performing any other setups. After registering each base station, register each
COMMUNICATOR
®
that will be used with that base according instructions in section 2.3.2, page 8.
NOTE: If using split-band operation, select the appropriate band prior to base station registration. If a
different frequency band needs to be selected to avoid interference, the primary base station must be
set to this frequency band before base station registration is started.
Register each base station and all Belt Packs and/or All-In-One Headsets as follows:
On one of the base stations, ensure that the primary/secondary switch is set to primary. On the
others, ensure that it is set to secondary.
NOTE: In split band operation, there can be one primary and up to three secondary base stations in
either band.
Turn the primary base station power on. Register any Communicators to be used with the primary base
station, as instructed in
section 2.3.2, page 8. Turn each Communicator off after registering it.
Power on one secondary base station. The STATUS display will show a double bar, indicating the
secondary base station is ready to be registered.
Double bar Small “o”
Base station ready to be initialized Small "o" indicates primary base
station is open for registration
REG (register) b STATUS display will show a small “o.” Press the utton on the primary base station. The
To assign a number to a secondary base station and register it, press the REG button on the
secondary base station. Pressing the button repeatedly causes it to cycle through the numbers 1, 2,
and 3. When the desired number appears, stop pressing and wait. While the secondary base station
is registered using the displayed number, the STATUS display will continue showing the secondary
number selected. When registration of the secondary base station is fin
one bar, to indicate the secondary has been registered to the primary.
ished, the display will show
section 2.3.2, page 8
Secondary 2 searching for primary Secondary is initialized to primary
One bar
Secondary base number
Press the REG button on the primary. The STATUS display will go blank.
Register Communicators to the secondary base stations as instructed in . After
registration, turn off the secondary base station and all Communicators.
23
Clear-Com HME DX210 System Guide