User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications
Spectrum Friendly
All DX Series wireless intercom systems now feature Spectrum Friendly™ technology for interference-free
operation in the increasingly crowded 2.4GHz frequency band. This new technology enables broadcast
and theatrical production crews to avoid emerging frequency conflicts by designating the 2.4GHz operating
frequency range: low-, high-, or full-band. While generally not a problem when separated, multiple
applications and multiple users of the same applications in close proximity can result in additional risk for
trouble-free operation. The new technology further ensures that products do not add interference to the
spectrum for other essential wireless services in the vicinity, such as DMX-controlled lighting.
Avoiding Wi-Fi Interference
To avoid interference with Wi-Fi systems, it is recommended to set the Wi-Fi system to something other
than channel 6 or 7.
Your DX210 should be set to the high or low band opposite any Wi-Fi frequency range in use.
DX210 Low Band = 2.4000-2.4400 GHz
DX210 High Band = 2.4433-2.4830 GHz
Channel
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Wi-Fi Frequencies
2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484 GHz
26
Clear-Com HME DX210 System Guide