User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications

FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions
:(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communication. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
Changes or modifications not expressly approved by Clear-Com, LLC, an HM Electronics, Inc. company
could void the user’s authority to operate this equipment.
MANDATORY SAFETY INSTRUCTIONS
FOR INSTALLERS AND USERS
Use only manufacturer or dealer supplied antennas. The Federal Communications Commission has
adopted a safety standard for human exposure to RF (Radio frequency) energy, which is below the
OSHA (Occupational Safety and Health Act) limits.
The term “IC:” before the certification/registration number only signifies that the Industry Canada
technical specifications were met.
Base Station Antenna minimum safe distance: 7.9 inches (20 cm) at 100% duty cycle.
Base Station Antenna gain: This device has been designed to operate with an antenna having a
maximum gain of up to 7dBi.
Antenna mounting: The antenna(s) used for the base transmitter must be installed to provide a
separation distance of at least 7.9 inches (20 cm) from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
Antenna substitution: Do not substitute any antenna for the one supplied by the manufacturer. You
may be exposing person or persons to excess radio frequency radiation. You may contact your dealer or
the manufacturer for further instructions.
WARNING: Maintain a separation distance from the base station transmit antenna to a person(s) of at
least 7.9 inches (20 cm) at 100% duty cycle.
WARNING: Excessive sound pressure level from earphones or headphones can cause hearing loss.
You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to
ensure the minimum separation distance (above) is maintained between the antenna and nearby persons
for satisfying exposure compliance. The operation of this transmitter must satisfy the requirements of
Occupational /Controlled Exposure Environment, for work-related use. Transmit only when person(s) are
at least the minimum distance from the properly installed, externally mounted antenna.
Korea: 해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음
Clear-Com HME DX210 System Guide










