User Manual
Table Of Contents
- 1 System Overview 1
- 1.1 System Components 1
- 1.2 Base Station Front Panel 2
- 1.3 Base Station Rear Panel 2
- 1.4 Belt Pack – BP210 3
- 1.5 All-In-One Headset – WH210 3
- 2 System Setup 4
- 2.1 Battery Charging 4
- 2.1.1 Connect AC Power Supply 4
- 2.1.2 Charge Batteries 5
- 2.2 Basic Base Station Setup 6
- 2.3 COMMUNICATOR® Setup and Registration 7
- 2.3.1 Set Up COMMUNICATOR®s 7
- 2.3.2 Register COMMUNICATOR®s 8
- 2.3.3 COMMUNICATOR® Settings 9
- 2.4 Interfacing with 2-Wire or 4-Wire Intercoms 10
- 2.5 Interfacing with Auxiliary Audio Equipment 11
- 2.6 ISO Relay 12
- 3 System Operation 13
- 3.1 Base Station Operation 13
- 3.1.1 Digital Radio Controls and Indicator Lights 13
- 3.1.2 Local Headset Connector, Controls and Indicator Lights
- 3.2 COMMUNICATOR® Operation 14
- 3.2.1 Power On/Off 14
- 3.2.2 ISO (Isolate) and IC1, IC2 (Intercom) 14
- 3.2.3 Operating Modes 14
- 3.2.4 Volume Up/Down 14
- 3.2.5 Adjusting Microphone Gain 15
- 3.2.6 Adjusting BP210 Belt Pack Side Tone 15
- 3.2.7 Using WH210 All-In-One Headset Lights-Off Mode 15
- 3.2.8 Changing COMMUNICATOR® Batteries 15
- 4 Troubleshooting 16
- 5 Technical Data 17
- 5.1 BS210 Base Station Specifications 17
- 5.2 BP210 Belt Pack Specifications 18
- 5.3 WH210 All-In-One Headset Specifications 19
- Appendix A: COMMUNICATOR® Indicator Light Functions 20
- Appendix B: Multiple Base Station Daisy-Chaining 21
- Appendix C: Jumper Settings 22
- Appendix D: Multiple Base Station Registration 23
- Appendix E: Interference Avoidance through Spectrum Friendly
- Appendix F: Audio Routing Diagram 27
- System Components
- Base Station Front Panel
- Base Station Rear Panel
- Belt Pack – BP210
- All-In-One Headset – WH210
- Battery Charging
- Basic Base Station Setup
- COMMUNICATOR® Setup and Registration
- Interfacing with 2-Wire or 4-Wire Intercoms
- Interfacing with Auxiliary Audio Equipment
- ISO Relay
- Base Station Operation
- COMMUNICATOR® Operation
- BS210 Base Station Specifications
- BP210 Belt Pack Specifications
- WH210 All-In-One Headset Specifications

Contents
1 System Overview ..........................................................................................................................1
1.1 System Components............................................................................................................................1
1.2 Base Station Front Panel ..................................................................................................................... 2
1.3 Base Station Rear Panel...................................................................................................................... 2
1.4 Belt Pack – BP210 ...............................................................................................................................3
1.5 All-In-One Headset – WH210............................................................................................................... 3
2 System Setup ................................................................................................................................4
2.1 Battery Charging .................................................................................................................................. 4
2.1.1 Connect AC Power Supply.............................................................................................................. 4
2.1.2 Charge Batteries .............................................................................................................................5
2.2 Basic Base Station Setup..................................................................................................................... 6
2.3 COMMUNICATOR
®
Setup and Registration........................................................................................ 7
2.3.1 Set Up COMMUNICATOR
®
s........................................................................................................... 7
2.3.2 Register COMMUNICATOR
®
s ........................................................................................................ 8
2.3.3 COMMUNICATOR
®
Settings........................................................................................................... 9
2.4 Interfacing with 2-Wire or 4-Wire Intercoms ....................................................................................... 10
2.5 Interfacing with Auxiliary Audio Equipment ........................................................................................ 11
2.6 ISO Relay........................................................................................................................................... 12
3 System Operation .......................................................................................................................13
3.1 Base Station Operation ...................................................................................................................... 13
3.1.1 Digital Radio Controls and Indicator Lights ................................................................................... 13
3.1.2 Local Headset Connector, Controls and Indicator Lights .............................................................. 13
3.2 COMMUNICATOR
®
Operation........................................................................................................... 14
3.2.1 Power On/Off ................................................................................................................................14
3.2.2 ISO (Isolate) and IC1, IC2 (Intercom)........................................................................................... 14
3.2.3 Operating Modes........................................................................................................................... 14
3.2.4 Volume Up/Down .......................................................................................................................... 14
3.2.5 Adjusting Microphone Gain ........................................................................................................... 15
3.2.6 Adjusting BP210 Belt Pack Side Tone .......................................................................................... 15
3.2.7 Using WH210 All-In-One Headset Lights-Off Mode ...................................................................... 15
3.2.8 Changing COMMUNICATOR
®
Batteries ....................................................................................... 15
4 Troubleshooting..........................................................................................................................16
5 Technical Data.............................................................................................................................17
5.1 BS210 Base Station Specifications .................................................................................................... 17
5.2 BP210 Belt Pack Specifications ......................................................................................................... 18
5.3 WH210 All-In-One Headset Specifications......................................................................................... 19
Appendix A: COMMUNICATOR
®
Indicator Light Functions........................................................20
Appendix B: Multiple Base Station Daisy-Chaining .................................................................... 21
Appendix C: Jumper Settings........................................................................................................ 22
Appendix D: Multiple Base Station Registration..........................................................................23
Appendix E: Interference Avoidance through Spectrum Friendly.............................................25
Appendix F: Audio Routing Diagram............................................................................................ 27
Clear-Com HME DX210 System Guide










