MAX™ EX Installation & Operation Manual ClearOne Communications, Inc. ~ 5225 Wiley Post Way, Salt Lake City, UT 84116 ~ tel 1-800-945-7730 ~ fax 1-800-933-5107 Printed in China.
ii Table of Contents Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Service and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Product returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Important safety information . . . . . . . . . . . . . . . . . . .
2 Introduction Important safety information Read the safety instructions before first use of this product.This conferencing phone is not designed for making emergency telephone calls when the power fails. Make alternative arrangements for access to emergency services. • Read and understand all instructions and follow all warnings marked on the product. • Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Getting Started 5 Getting Started Connecting to a digital phone line Getting Started WARNING! Do not connect the conference phone directly to a digital (PBX) line, PERMANENT DAMAGE MAY RESULT. Connecting your conferencing phone If you have digital (PBX) telephone service, you need to run an analog extension from the PBX (recommended for best performance) or use a digital-to-analog telephone line converter. For more information, contact ClearOne Technical Support.
6 Getting Started 7 Getting Started Using your MAX EX conferencing phone To access your service center To make a call • While in Standby mode, press and hold the 0 key for 2 seconds. This feature must be programmed before use. See page 10. 1. Press the ON/OFF key. You will hear a dial tone. 2. Dial the number as you would on a standard phone. The number appears on the LCD screen. To store a number in the phonebook Figure 5. Dialing screen 1.
8 User Options 9 User Options To mute during ringing User Options • Press the star (*) or the MUTE key to mute the ringer for the duration of the ringing. Note:This only mutes the current ring. Once a new call comes in, the ringer will not be muted.
10 User Options To program local phone number 11 User Options 1. Press and hold REDIAL/PROG until the Program icon appears on the LCD screen. To program the Automatic Gain Control (AGC) and Automatic Level Control (ALC) settings 2. Press 4 to enter the user phone number menu. 1. Press and hold the REDIAL/PROG key until the Program icon appears on the LCD screen. 3. Press REDIAL/PROG. 2. Press and hold the 8 key.The current AGC setting number will be displayed on the LCD screen. 3.
12 Maintenance Maintenance Caring for your MAX EX 13 Maintenance If you hear It could be that Try this No dial tone Base unit is not connected to telephone jack. Connect the base unit to the telephone jack using the supplied telephone cable. You are not using an analog phone line. Check that you are using an analog phone line. Consult your IT department for help. You have a bad telephone connection. Place the call again to see if another line provides a better connection.
14 Appendix 15 Appendix Compliance Appendix FCC Part 15/ICES-003 Compliance Specifications DIMENSIONS (W x D x H) Phone section: 10.5" x 10.5" x 3" (26.7 cm x 26.7 cm x 7.6 cm) Base unit: 4.25" x 5.5" x 2.5" (10.8 cm x 14 cm x 6.4 cm) WEIGHT Phone section: 2.7 lb (1.2 kg) Base unit: .6 lb (0.27 kg) Shipping: 10 lb (4.
16 Appendix 17 Appendix IC Compliance Warranty IC: 1970A-158015 ClearOne Communications, Inc. (Manufacturer) warrants that this product is free of defects in both materials and workmanship. For warranty information and coverage, refer to the ClearOne website at www.clearone.com. Ringer Equivalence Number (REN): 0.1B(ac) Notice The term "IC" before the certification/registration number signifies that Industry of Canada technical specifications were met.
