Max™ EX Installation & Operation Manual ClearOne Communications, Inc. ~ 1825 Research Way, Salt Lake City, UT 84119 ~ tel 1-800-945-7730 ~ fax 1-800-933-5107 Printed in China.
ii Table of Contents 1 Introduction Thank you for purchasing the ClearOne Max™ EX expandable conferencing phone. Max EX provides premium, full-duplex audio to small conference rooms as a single unit and to larger rooms as an expanded system. Up to four Max EX units can be linked, expanding not only microphone coverage but loudspeaker coverage and control access as well.This creates even distribution of sound for a more natural communications experience.
2 Introduction ! Important safety information Read the safety instructions before first use of this product.This conferencing phone is not designed for making emergency telephone calls when the power fails. Make alternative arrangements for access to emergency services. • Read and understand all instructions and follow all warnings marked on the product. • Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Getting Started Getting Started Getting Started Connecting your conferencing phone 1. Connect the Cat. 5 cable from the Link Out jack on the base unit to the Link In jack on the conferencing pod. 2. Connect the base unit to the telephone jack using the RJ-11 telephone cable. 3. Plug the the base unit directly* into a wall-mounted electrical outlet. * International versions of the Max EX base unit do not plug directly into the electrical outlet. A separate power supply cord is included.
6 Getting Started Using your Max EX conferencing phone To store a number in the phonebook To make a call 1. Enter the phone number you want to store while conferencing pod is in Standby mode. 1. Press the ON/OFF key. You will hear a dial tone. 2. Dial the number as you would on a standard phone. The number appears on the LCD screen. Figure 5. Dialing screen Note: You can also predial the number while in Standby (inactive) mode and press the ON/OFF key to connect the call.
8 User Options 9 User Options Programming options User Options Call options In addition to the basic phone operations described in the previous section, you can perform any of the following functions during a call: temporarily change to tone dialing, send a flash signal, display phone number and adjust speaker volume.
10 User Options 11 User Options To program local phone number To restore factory defaults 1. Press and hold REDIAL/PROG until the Program icon appears on the LCD screen. 2. Press 4 to enter the user phone number menu. 1. Press and hold the REDIAL/PROG key until the Program icon appears on the LCD screen. 3. Press REDIAL/PROG. 2. Press and hold the 9 key. The number 8 appears across the LCD screen. 3. Enter the local phone number. 3. Press REDIAL/PROG to confirm selection. Press CLEAR to exit. 4.
12 Maintenance Maintenance Caring for your Max EX 13 Maintenance If you hear It could be that Try this No dial tone Base unit is not connected to telephone jack. Connect the base unit to the telephone jack using the supplied telephone cable. You are not using an analog phone line. Check that you are using an analog phone line. Consult your IT department for help. You have a bad telephone connection. Place the call again to see if another line provides a better connection.
14 Appendix 15 Appendix Compliance Appendix FCC Part 15/ICES-003 Compliance Specifications DIMENSIONS (W x D x H) Phone section: 10.5" x 10.5" x 3" (26.7 cm x 26.7 cm x 7.6 cm) Base unit: 4.25" x 5.5" x 2.5" (10.8 cm x 14 cm x 6.4 cm) WEIGHT Phone section: 2.7 lb (1.2 kg) Base unit: .6 lb (0.27 kg) Shipping: 10 lb (4.
16 Appendix 17 Appendix IC Compliance Product Return and Repair IC: 1970A-158015 1. Return to Seller if Purchased Through an Authorized Dealer Ringer Equivalence Number (REN): 0.1B(ac) a. Proof of purchase date from reseller within warranty period must be provided by the end user. Notice b. Seller may, at its discretion, provide an immediate exchange or repair or may return the unit to the Manufacturer for repair.
