User's Manual

Digital Wireless Microphone Systems
Quick Start Guide
Seng Up Pre-Engineered ClearOne
®
Systems for Opmal Performance
Master
Slave
Terminators
HEADQUARTERS:
Salt Lake City, UT USA
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
Tel: [phone]
Toll Free: 800.945.7730
Fax: [phone]
e-mail: [e-mail]
EMEA
Tel: [phone]
e-mail: [e-mail]
APAC
Tel: [phone]
e-mail: [e-mail]
LATAM
Tel: [phone]
e-mail: [e-mail]
TechSales
Tel: [phone]
e-mail: [e-mail]
Technical Support
Tel: [phone]
e-mail: [e-mail]
CLEARONE LOCATIONS
Open the Cartons: Conrm everything on the packing slip is enclosed.
Set up the Docking Staon:
1. ClearOne transmiers are shipped with rechargeable baeries. Plug
in the charging dock, put the baeries in the transmiers, then place the transmiers in the dock
while you set up the rest of the system.
Mount the Receivers in the Rack
2. and connect them to power. Conrm the displays light up.
Pre-engineered Antenna Design:
3. If you provided ClearOne with a oor plan, you will nd a
marked up version in the box (or, in your Email in-box) showing the antenna design along with the
antennas and pre-made cables. Place the antennas according to the drawings.
Your Own Design:
A. If you did not request an antenna design, place the antennas according to
the enclosed Antenna Applicaons Guide Improper antenna placement is the main cause of
poor RF performance.
Dipole Antennas:
B. Dipole antennas mounted to the rack equipment can easily be locked
away in a closet/rack cabinet. This results in poor RF performance because there is no line
of sight between the transmier and receiver antenna. Therefore, remote antennas are
preferred. See the Antenna Applicaon Guide for details.
Connect the Antennas:4. The receiver that connects to the antennas should be set as the
Antenna Master receiver. Master is the factory default. If your system daisy-chains antennas
together, the downstream receivers should be set as Slaves. Terminators are used on the
last system in the daisy-chain. Use ClearOne Remote’s Antenna Setup Wizard, which opens
automacally the rst me you connect. You can also nd the wizard under the SETTINGS tab
of the main page. If connecng ClearOne acve remote antennas, make sure the red LED lights
up. If not, check the receiver’s antenna phantom power seng using the ClearOne Remote
Control Soware.
Connect the analog outputs to the mixer:5. The system is shipped with Euro block connectors.
The default output level is set to +4 dBu. Note that factory default for the front panel headphone
jack is set for mixed line-level out. Use ClearOne Remote>Sengs>Headphone, to reset for
headphones.
CAUTION! Turn o phantom power from the mixer. Phantom power distorts the audio quality
of your microphones.
System Test:6. In most cases, the system is now ready to use. Conrm all channels pass audio
perfectly.
Modicaons (FCC 15.21)
Changes or modicaons to this equipment not expressly approved by ClearOne may void the user’s authority to operate this equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operaon of the device.
Applies to WS80-T:
Under Industry Canada regulaons, this radio transmier may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmier by Industry Canada.
To reduce potenal radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communicaon.
This radio transmier (WS80-T) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for
each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Monopole antenna, 0dbi gain, 50 ohm impedance.
Le présent émeeur radio (DS80-T) a été approuvé par Industrie Canada pour fonconner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance
requise pour chaque type d’antenne. Les types d’antenne non inclus dans cee liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitaon de
l’émeeur.