User's Manual
Table Of Contents
- _gen_
- Important Safety Information
- INTERACT Software Overview
- INTERACT MIC EX
- INTERACT Dialers
- INTERACT Com / COM-W (Wireless)
- Network Connection
- Phonebook
- Regional Settings
- Event Log
- System Checks
- Firmware Loader
- INTERACT COM Updater
- Serial Commands
- INTERACT AT
- Basic Connections
- Device Toolbox - INTERACT AT
- Mixer Console - INTERACT AT
- Line Input Settings - INTERACT AT
- Line Output Settings -- Interact AT
- Camera Control
- Dialer - INTERACT AT
- Communications Settings - INTERACT AT
- Record Output Settings -- INTERACT AT
- INTERACT Mic and Mic EX Settings - INTERACT AT Only
- Playback Input Settings - INTERACT AT
- Telephone Settings - INTERACT AT
- Loudspeaker Settings - INTERACT AT
- INTERACT COM Settings - INTERACT AT
- INTERACT PRO
- INTERACT PRO 8i
- Device Toolbox - INTERACT PRO
- Mic Settings - INTERACT PRO
- Mixer Console - INTERACT PRO
- Line Input Settings - INTERACT PRO
- Presets - INTERACT PRO
- Dialer - INTERACT PRO
- Communications Settings - INTERACT PRO
- COM Settings - INTERACT PRO
- Telcos - INTERACT PRO
- Processing Settings - INTERACT PRO
- Output Settings - INTERACT PRO
- Compliance
- Bookmarks
Audio Conferencing Setup (INTERACTAT)
Setting up Audio Conferencing
1. If you are installing the mixer into a rack, remove the side panels, rotate them and then reat-
tach.
2. Connect the first microphone breakout box to the mixer with a Cat. 5 cable.
3. Connect the second and third INTERACTMICEX boxes using Cat. 5 cables. (Third breakout
box on the INTERACTAT only).
4. Connect the microphones to the breakout boxes, as desired.
5. Connect the speakers to the mixer.
6. Using the RJ-11 cable, connect an analog telephone jack to the Line jack on the mixer.
7. Using an RJ-11 cable (not supplied), connect an analog telephone set to the Set jack on the
mixer (optional).
8. Using the 7' Cat. 5 cable, connect the mixer to the network. (Network settings can be
changed in INTERACT software.)
9. Using the power supply cords, connect the mixer to an electrical outlet.
10. If using the wired controller, connect the controller to the mixer’s RS-232 serial port using the
supplied RJ-11 to DB-9 adapter. If using the RF controller, attach the external antenna and
turn it until it is upright.
11. If using the RF controller, insert four AAA batteries into the battery compartment in the bot-
tom of the unit.
Setting up Audio Conferencing (INTERACTPRO)
1. If you are installing the mixer into a rack, remove the side panels, rotate them and then reat-
tach.
2. Connect the first microphone breakout box to the mixer with the 18” Cat. 5 cable.
3. Connect the second and third INTERACTMICEX boxes using the 18” Cat. 5 cables. (Third
breakout box on the INTERACTAT only).
4. Connect the microphones to the breakout boxes, as desired.
5. Connect the speakers to the mixer.
6. Using the RJ-11 cable, connect an analog telephone jack to the Line jack on the mixer.
7. Using an RJ-11 cable (not supplied), connect an analog telephone set to the Set jack on the
mixer (optional).
8. Using the 7' Cat. 5 cable, connect the mixer to the network. (Network settings can be
changed in INTERACT software.)
9. Using the power supply cords, connect the mixer to an electrical outlet.
10. If using the wired controller, connect the controller to the mixer’s RS-232 serial port using the
supplied RJ-11 to DB-9 adapter. If using the RF controller, attach the external antenna and
turn it until it is upright.
11. If using the RF controller, insert four AAA batteries into the battery compartment in the bot-
tom of the unit.
- 21 -