MAX™ Wireless Installation & Operation Manual
ii Table of Contents Introduction 1 Table of Contents Introduction Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Thank you for purchasing the ClearOne MAX™ Wireless conferencing phone.
2 Getting Started Unpacking Carefully place the conferencing pod and base unit on a level surface. Ensure you have received all items shown below. Se To tti ng 1. ch up Sli arg co Co de the e nf ba er pac nne tte en k, ct the cover rie cin and off s g slid bat the ph e tery the pac bat on e cov k ter er plu y com bac g k into partm int ent o the pla por ce. t on the in the bot com tom par of tm the ent pod , ins . ert the 2. Fig 3. ure 1. Co Con ele nne nec ctr ct To ting ica the co 1.
Getting Started • Observe the proper polarity, or direction, of any battery. Reverse insertion of the battery pack can result in leakage or explosion. • Remove the battery pack if you do not plan to use the product for several months at a time. The batteries could leak over that time. • Discard any “dead” battery pack as soon as possible because they are likely to leak into the product. • Do not store this product or the battery pack in a high temperature area. Battery packs 5 Getting Started 2.
6 Getting Started Connecting to a digital phone line WARNING! Do not connect the conferencing phone directly to a digital (PBX) line, PERMANENT DAMAGE MAY RESULT. If you have digital (PBX) telephone service, you will need a digital-to-analog telephone line converter. For more information, contact ClearOne technical support. 7 Getting Started You can also predial the number while in Standby (inactive) mode and press the ON/OFF key to connect the call.
8 Getting Started 9 User Options When more than 18 characters are entered, a scroll button will appear on the LCD display and the numbers will scroll from right to left. To store a number in the phonebook 1. Enter the phone number you want to store while conferencing pod is in Standby mode. To send a Flash signal 2. Press and hold the PHONEBOOK/EDIT key until the Phonebook and Program icons appear on the LCD screen.
10 User Options 11 User Options 2. Press 1 to enter the Ringer Melody menu. There are five available melodies. 4. Enter the phone number. 3. Press REDIAL/PROG. The current melody selection will flash. 5. Press REDIAL/PROG to save the number. Press CLEAR to exit. 4. Press keys 1–5 to play the corresponding melody. The selected melody will play once. Press & hold the “1” key to enter a hyphen or the “*” key to enter a space in the number.
12 User Options Tones and alerts User Options 13 During a call Tone/Alert Description • Changing the speaker volume, and muting or unmuting the microphone, causes both pods to change simultaneously. Not powered If the base unit is not powered, you will hear a beeping sound when you press the Phone key. • If one pod loses its link to the base due to low battery power or being moved out of range, the call will continue on the other pod.
14 Maintenance If you hear It could be that Try this Appendix Beeping sound before dialing Pod section is out of range Move pod section closer to the base unit. Specifications Base unit is not powered. Make sure base unit is plugged into a power outlet and the Power LED is lit. Base unit is not connected to telephone jack. Connect the base unit to the telephone jack using the supplied telephone cable. DIMENSIONS (W x D x H) Phone section: 10.5" x 10.5" x 3" (26.7 cm x 26.7 cm x 7.
16 Appendix Compliance FCC Part 15/ICES-003 Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules and Industry Canada ICES-003.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
