Other Content

ManualsBrandsClearStream ManualsElectrical5 UHF/VHF Ultra Long Range Outdoor DTV Antenna

CLEARSTREAM™ 5

Before permanently attaching the antenna to any surface, TEST RECEPTION in that location.

Before beginning assembly, make sure all parts needed are present.

Tools Required: #2 Phillips Screwdriver and Adjustable Pliers

Sold Separately: Coaxial Cable and Antenna Mast

The CLEARSTREAM™ 5 includes:

1) Antenna Element

2) Reflector Assembly

3) 4 - Spacers

4) 8 - Screws and Washers

5) 2 - U-Bolts and Wing Nuts

6) 2 - Mast Clamps and Back Plates

Assembly:

1. Insert the Spacers (3) into the front of the Reflector Assembly (2) and

secure them using the Screws and Washers (4).

2. Align the back of the Antenna Element (1) with the Spacers (3) and

secure using the remaining Screws and Washers (4).

3. Insert the U-Bolts (5) through the top and bottom of the Reflector

Assembly (2). Add a Mast Clamp and Back Plate (6) to each U-Bolt (5),

and loosely screw on the Wing Nuts (5).

Installation:

1. Mount the assembled antenna by sliding the Mast Clamp (6) onto the

Antenna Mast.

2. Aim the front of the antenna toward the broadcast towers. Visit

antennapoint.com to locate the broadcast tower(s) near you.

3. Tighten the Wing Nuts (5) to secure the antenna onto the Antenna Mast

4. Thread one end of the coaxial cable onto the connector located at the bottom

of the Antenna Element (1).

5. Thread the other end of the coaxial cable onto the Antenna Input of the

TV/converter box.

6. Perform a channel scan on your TV/converter box for the available channels.

1-877-825-5572

Toll-Free HELPLINE

Technical Assistance is available:

Monday – Friday 9:00 am – 9:00 pm

Saturday – Sunday 10:00 am – 6:00 pm

Central Standard Time

Helpful Tips:

Before permanently installing your antenna to any surface, check the

signal reception by temporarily connecting coaxial cable to your antenna

and then to your TV/converter box. Follow the instructions in your TV

owner’s manual to change the input from “CABLE” to “ANTENNA”, “AIR”,

or “BROADCAST” using the TV’s remote control. Scan for channels.

NOTE: Follow the assembly/installation instructions included with the

Antenna Mast of your choice before beginning the installation.

If reception is not as desired, move the antenna and rescan for

the available channels.

Face the Front of the Antenna

Toward Transmitters

Summary of content (2 pages)

PAGE 1
CLEARSTREAM™ 5 Before permanently attaching the antenna to any surface, TEST RECEPTION in that location. Before beginning assembly, make sure all parts needed are present. Tools Required: #2 Phillips Screwdriver and Adjustable Pliers Sold Separately: Coaxial Cable and Antenna Mast The CLEARSTREAM™ 5 includes: 1) Antenna Element 2) Reflector Assembly 3) 4 - Spacers 4) 8 - Screws and Washers 5) 2 - U-Bolts and Wing Nuts 6) 2 - Mast Clamps and Back Plates Assembly: 1.
PAGE 2
Troubleshooting: Problem: I’m not getting any signals at all. Possible causes: 1. Analog-only televisions (manufactured before 2007) need a digital converter box.You MUST perform a channel scan on the converter box 2. A digital TV must be programmed in order to receive digital channels. a) A TV must be set to the proper input source. Select the proper input through the Setup menu. It may be labeled “Antenna”, “Broadcast”, or “Air”. b) Within the Setup menu, select channel setup or channel scan.