ORBIS SCRUBBER POLISHER RANGE OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Web: www.clemas.co.uk Email: info@clemas.co.
ORBIS 200 & 400 SCRUBBER POLISHER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.
Fig. 1 Fig. 2 Fig. 3 Fig.4 Fig.
Contents Page 1 General Information .......................................................................... 1.1 Important safety advice ............................................................. 1.2 Guidelines for the operator ........................................................ 1.3 Transporting the machine .......................................................... 1.4 Electrical connection .................................................................. 5 5 5 5 5 2 Preparing for use .........
IMPORTANT READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE 1 General Information 1.2 Guidelines for the operator These floor cleaning machines are designed for the scrubbing and polishing of hard floors and/or shampooing of carpets in indoor areas. They should not be used in outdoor areas or where excessive moisture is present. These instructions are valid for the following models.
Connection point for vacuum unit lead. 2 Preparing for use Drive plate 2.1 Fitting the handle 1. Carefully remove the machine base and handle from their respective packaging. 2. Check that the following items are present with the base and remove them from their transit position. M8 x 70 Hex.Hd. bolt (3) M8 Nyloc Hex. nut (3) M8 Plain washer (6) 13mm A/F Spanner (2) 3.
• Once the machine has started the interlock buttons should be released. 4.5 Fitting the solution tank NOTE - The solution tank is supplied as an accessory item, complete with attachments and fitting instructions. • To stop the machine release both switch triggers. 4.2 Orbis 452/400 dual speed The speed selector switch on the dual speed model is located on the motor housing. Ensure machine is switched off before changing the speed setting.
The cut-out will operate to protect the motor from overheating by switching the machine off when there is excessive friction/resistance to the cleaning head on the floor. This is usually caused by the stickiness of the pad or floor. Turn the cleaning pad over or if both sides are dirty replace with a clean pad. It is not possible to obtain a good finish on the floor using a dirty pad. Should the cut-out operate it will reset automatically when the motor has cooled sufficiently, usually after 15 - 30 mins.
Technical specification All models : 230-240V ∼ 50Hz, Class I construction. Enclosure to IPX4. Fitted with 15m supply cord type and 13A fused plug. Model 45cm 45cm 45cm 200 400 2/400 Pad diameter cm 43 43 43 Pad pressure gm/cm² 22 22 27,5 rpm 190 380 190/380 Motor rating W 1100 1100 1100 Max.
Accessories Item Part No.
Fault diagnosis The following simple checks may be performed by the operator. Trouble Reason Remedy Machine not working, neon indicator not lit. Lack of voltage/electrical supply. Check fuse *, supply cord, plug and socket outlet. Machine not working, neon indicator lit. Switch interlock incorrectly operated. Check operating procedure in instructions. Motor overload cut-out operated. Check brush/pad for good condition. Check correct liquid type & quantity. Check liquid dilution.
ORBIS COMPACT SCRUBBER POLISHER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.
Contents Page 1 Product information ................................................................... 4 1.1 Important safety advice ............................................................... 1.2 Guidelines for the operator .......................................................... 1.3 Transporting the machine ............................................................ 4 4 4 2 Preparing for use ........................................................................ 5 2.1 Electrical connection ...
IMPORTANT READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE 1 Product information These floor cleaning machines are designed for the scrubbing and polishing of hard floors and/or shampooing of carpets in indoor areas. They should not be used in outdoor areas or where excessive moisture is present. The following instructions contain important information about the machines and safety advice for the operator.
2 Preparing for use 2.1 Electrical connection Before connecting the machine to the power supply, check that your supply voltage corresponds with that marked on the rating label on the handle of the machine. The power supply cord plus any extension leads should not exceed 30m in total, otherwise you may experience problems starting up the machine. The cross-section of any extension cable wiring must be at least 2,5 mm². UK only The supply cord is fitted with a non rewireable plug containing a 13 amp fuse.
4.1 Starting the machine • Fully unwind the supply cord from the handle and plug into a convenient socket outlet. The neon indicator on the handle should light showing that power is available. • With the handle set at a convenient working height and with both left and right hands on the handle, depress both interlock buttons with the thumbs and squeeze both switch triggers to start the machine (Fig.2). Ensure transport wheels are not touching the floor during start-up and operation (Fig 3).
necessary. Blocked vents will cause the motor to overheat, and may lead to premature failure. Warranty claims for this type of damage will not be accepted • Solution tank - Check water flow, if restricted inspect hoses and tubes for blockage or kinks. Dismantle control valve to clean if necessary. Check switch interlock for correct operation. • Motor overload cut-out - All machines are fitted with an automatic reset motor overload cut-out.
9 Technical Specification All models : Class I construction. Enclosure to IPX4. Fitted with 15m supply cord type H05VV-F 3x1.0mm² (10A), and non rewireable plug. Model OB28240 Working width cm 28 Pad diameter cm 28 Pad pressure gm/cm² 24.4 Voltage a.c. V 220 - 240 Frequency Hz 50 Motor speed rpm 1400 Motor rating W 550 Handle height cm 115 Weight kg 22 Noise Level (see note 1) dB(A) 71.4 Handle vibration (see note 2) m/s² < 2.
11 Fault diagnosis The following simple checks may be performed by the operator. Trouble Reason Remedy Machine not working, neon indicator not lit. - Lack of voltage/electrical supply. - Check fuse *, supply cord, plug and socket outlet. Machine not working, neon indicator lit. - Switch interlock incorrectly operated. - Check operating procedure in instructions. Machine wobbles or vibrates excessively. - Pad worn or damaged. - Renew pad. - Pad dirty. - Clean the pad.
ORBIS CORDLESS BURNISHER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.
ORBIS DUO SCRUBBER POLISHER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.
