Operators Manual Installation, Operation & Service Skillets TABLE TOP ELECTRIC SKILLETSMODELS: SET-10 SET-15 SET-15 SET-10 ™ Cleveland Enodis 1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www.clevelandrange.com SE95031 rev.
FOR THE USER WARNING: ! Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the Installation and Operating instructions thoroughly before installing or servicing this equipment. IMPORTANT THE INSTALLATION AND CONNECTION MUST COMPLY WITH THE LOCAL AND NATIONAL ELECTRICAL CODES.
INSTALLATION GENERAL INFORMATION INSPECTION / UNPACKING These instructions must be retained by the owner/user for future reference. 1. Before unpacking visually inspect the unit for evidence of damage during shipping. The serial plate is located on the right side of the control housing. Voltage, phase, amperage and wattage are stated on the plate. 2. If damage is noticed, do not unpack the unit, follow "SHIPPING DAMAGE INSTRUCTIONS" shown below.
INSTALLATION CLEARANCES This unit must be installed in accordance with the following clearances in order to provide proper operation and servicing of the appliance. Also, it is recommended the unit be installed with sufficient clearances to provide proper cleaning and maintenance. Clearances SET-10 - RIGHT: 3”, LEFT: 0”, REAR 1” SET-15 - RIGHT: 4”, LEFT: 4”, REAR 1/2” Make four 3/8" holes in an existing stand or countertop, in order to secure the base of the skillet.
OPERATING INSTRUCTIONS 1. Ensure that the electrical supply to the skillet is turned on. 2. Before cooking, be sure that the skillet's cooking surface is clean, and that the skillet is in the fully lowered position. 3. Place the skillet's power on/off switch to the "on" position. 4. Pre-heat skillet for approximately 10 minutes by turning the temperature control knob to the desired temperature setting (see TEMPERATURE APPLICATION CHART).
CLEANING INSTRUCTIONS CAUTION SURFACES MAY BE EXTREMELY HOT! CLEANING INSTRUCTIONS 1. Turn unit off. 2. Prepare a warm water and mild detergent solution in the unit. 3. Remove food soil using a nylon brush. CARE AND CLEANING Cooking equipment must be cleaned regularly to maintain its fast, efficient cooking performance and to ensure its continued safe, reliable operation. The best time to clean is shortly after each use (allow unit to cool to a safe temperature).
STAINLESS STEEL EQUIPMENT CARE AND CLEANING (Supplied courtesy of Nafem. For more information visit their web site at www.nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. 4. Treat your water. Though this is not always practical, softening hard water can do much to reduce deposits. There are certain filters that can be installed to remove distasteful and corrosive elements. To insure proper water treatment, call a treatment specialist. Corrosion on metals is everywhere.
SERVICE PARTS WARRANTY Our Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance and Repair Centre for replacement parts, service, or information regarding the proper maintenance and repair of your cooking equipment In order to preserve the various agency safety certification (UL, NSF, ASME/Ntl. Bd., etc.), only factorysupplied replacement parts should be used. The use of other than factory supplied replacement parts will void warranty.
MODEL SET-10 SKILLET BOTTOM (for units built prior to August 2007) Tighten to 11 ft-lb & apply locktite ITEM NO. PART NO. DESCRIPTION QTY. 1 2 SK2231500 FA21024 SPHERICAL WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 5/16-18 HEX. NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 3 SK2231498 ELEMENT BLOCK ASSEMBLY, 208V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL SET-10 SKILLET BOTTOM (for units built after August 2007) Tighten to 11 ft-lb & apply locktite ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. SK00008 FA11145 SK2232000 FA32006 FA10245 SK603281 SK603280 SK2231498 KE55340 SK2231699 SK603284 FA21024 SK2231500 SK603282 FA11145 DESCRIPTION QTY. PAN WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 10/32X3/8 CROSS HEAD SCREW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL SET-10 CONTROL HOUSING DRAWING (for units prior to August 2007) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO. F12 SK2234200 KE52192 SK1019701 SK2238099 KE50042 F87 KE50376 KE50377 KE50750-2 SK2234400 SK2240800 SK2235100 SK50062 SK2235000 KE55069-2 SK2234800 SK2234801 FA10140 KE50569-1 SK50047-2 DESCRIPTION QTY. SCREW, COVER, 10 - 24 X'/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SPRING . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL SET-10 ASSEMBLY DRAWING (for units built after August 2007) 48 5A 5B 5C 5D
MODEL SET-10 ASSEMBLY DRAWING (for units built after August 2007) ITEM NO. 2 5A 5B 5C 5D 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 43 44 45 46 47 48 PART NO.
MODEL SET-15 SKILLET BOTTOM & COVER VENT CAP MARINE LOCK 19 20 ITEM NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 SK2211500 FA30505-1 SK2211100 SK2209300 SK2211300 SK2211099 SK2211200 SK2275300 KE00349 SK2276097 KE55069-2 SK2232001 SK2231500 SK2274000 KE55340 SK2277100 KE50886-4 KE50151-2 KE54907-15 FA15019-5 KE600550 Screw, 1/4”-20 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL SET-15 SKILLET CONTROL HOUSING (for units built prior to November 2005) ITEM NO. PART NO. DESCRIPTION 1 SK2274900 KE54846-3 F12 SK2275200 SK2235100 SK2236600 KE50569-1 Cover, Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Gasket, Control Box Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Screw, Cover, 10-24 x '/z" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL SET-15 SKILLET CONTROL HOUSING (for units built after November 2005) 27 28 19 9 21 1 14 21 3 34 21 7 1 2 SECTION C-C 12 10 16 22 21 26 5 PLACE ITEM #13 BETWEEN ITEM #1 AND ITEM #7, 2 PLACES DETAIL NOT SHOWN ON THIS DRAWING. ITEM NO. 1 2 3 5 6 7 9 10 11 12 13 14 34 16 19 21 22 26 27 28 PART NO. KE001075 KE001074 KE601103 REF.
MODEL SET-15 BASE/PAN ASSEMBLY (for units built after November 2005) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 21 22 23 PART NO. KE000851 SK00348 SK2274299 SK2273599 KE001187 SK50403 SK50434 FA95081-3 SK50826 FA31033 FA11509-2 FA11258 KE600550 FA15019-5 FA95007-9 FA11323 KE601034 KE600284-3 FA95031 17 18 19 20 SK00384 KE54846-6 KE54833-1 FA21006 DESCRIPTION QTY. BASE WELDMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SUPPORT BAR ASS'Y, L.H. . .
MAINTENANCE SERVICING GUIDE This section contains servicing information intended for use by Authorized Service Personnel. A/ PROBLEM: Skillet fails to heat with pilot light on. Probable Cause Test and Remedy 1. Faulty contactor(s) Check coil(s) and contacts of contactor(s). Replace if necessary. 2. Faulty wiring Check wiring to contactor(s). Replace if necessary. B/ PROBLEM: Skillet fails to heat with pilot light off.(power switch must be on and thermostat set). Probable Cause Test and Remedy 1.
HEATING ELEMENT REMOVAL HEATING ELEMENT BLOCK TORQUING 1. Tilt the skillet forward to access bottom cover plate. Uneven torquing of heating element block retaining plate nuts may cause uneven heating of the cooking surface. To retorque, proceed as follows: 2. Make sure power switch and external circuit breaker (at fuse box or breaker panel) are off. 3. Remove screws from bottom cover plate. Remove plate. 1. Tilt the skillet forward. 4.
WIRING DIAGRAM, SET-10 & SET-15 208, 220 or 240V, Single or Three Phase (for units built prior to November 2005)
WIRING DIAGRAM, SET-10 & SET-15 208/380 or 240/415V, Three Phase Y Connected (for units built prior to November 2005)
WIRING DIAGRAM, SET-10 & SET-15 480V, Single or Three Phase (for units built prior to November 2005)
WIRING DIAGRAM, SET-10 & SET-15 208, 220 or 240V, Single or Three Phase (for units built after November 2005)
WIRING DIAGRAM, SET-10 & SET-15 208/380 or 240/415V, Three Phase Y Connected (for units built after November 2005)
WIRING DIAGRAM, SET-10 & SET-15 480V, Single or Three Phase (for units built after November 2005)
