Preface Notebook Computer M720T/M728T/M729T/M730T Service Manual Preface I
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface About this Manual This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the M720T/ M728T/M729T/M730T series notebook PC. The following information is included: Chapter 1, Introduction, provides general information about the location of system elements and their specifications.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Warning Preface Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to persons when using any electrical equipment: 1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning. 3.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Preface Do not leave it in a place where foreign matter or moisture may affect the system. Don’t use or store the computer in a humid environment.
Preface 4. 5. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Take care when using peripheral devices. Use only approved brands of peripherals. Unplug the power cord before attaching peripheral devices. Power Safety Preface The computer has specific power requirements: • • • • • • Only use a power adapter approved for use with this computer.
Preface Battery Precautions Preface • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Contents Introduction ..............................................1-1 Disassembly ...............................................2-1 Overview .........................................................................................2-1 Maintenance Tools ..........................................................................2-2 Connections .....................................................................................2-2 Maintenance Precautions ...........................................
Preface Preface System Block Diagram ................................................................... B-2 Intel Penryn (Socket-P) 1/2 ............................................................ B-3 Intel Penryn (Socket-P) 2/2 ............................................................ B-4 Cantiga 1/6 - Host .......................................................................... B-5 Cantiga 2/6 - VGA, CRT ................................................................ B-6 Cantiga 3/6 - DDR ........
Introduction Chapter 1: Introduction Overview This manual covers the information you need to service or upgrade the M720T/M728T/M729T/M730T series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about drivers (e.g. VGA & audio) is also found in User’s Manual. That manual is shipped with the computer. Operating systems (e.g. Windows XP, Windows Vista, etc.) have their own manuals as do application software (e.g.
Introduction System Specifications Feature 1.Introduction Processor Specification Intel® Core™2 Duo Processor 35W - (478-pin) Micro-FC-PGA Package - Socket-P T9400/ T9600 45nm (45 Nanometer) Process Technology 6MB On-die L2 Cache & 1006MHz FSB 2.53/ 2.8 GHz Intel® Core™2 Duo Processor 25W - (478-pin) Micro-FC-PGA Package - Socket-P P8400/ P8600 45nm (45 Nanometer) Process Technology 3MB On-die L2 Cache & 1006MHz FSB 2.4/ 2.
Introduction Feature Specification One RJ-11 Modem Jack One RJ-45 LAN Jack One DC-In Jack One External Monitor Port Three USB 2.0 Ports One Headphone-Out Jack One Microphone-In Jack One S/PDIF Out Jack One Internal Microphone Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards require a PC adapter ExpressCard Slot One ExpressCard/34(54) Slot Communication 10M/ 100/ 1000Mb Base-TX Ethernet LAN Azalia 56K Modem V.90 & V.
Introduction Feature Environmental Spec Dimensions & Weight Optional *Note: 1.Introduction The 3.5G and Intel Turbo Memory Modules cannot coexist. There is only one slot available for either of these factory option modules. Specification Temperature Operating: Non-Operating: 5°C - 35°C -20°C - 60°C 20% - 80% 10% - 90% M720T/M728T/M729T: M730T: 299mm (w) * 219mm (d) * 26.5-35.7mm (h) 1.88 kg With 4 Cell Battery and ODD 310mm (w) * 233mm (d) * 30-36mm (h) 2.
Introduction External Locator - Top View with LCD Panel Open Figure 1 Top View 1 1 2 2 3 6 5 11 4 6 5 7 7 8 8 9 10 11 9 M720T/M728T/M729T 4 10 *Note: This model may have M730T either a fingerprint module or card reader module, depending on your purchase configuration. 6 6 5 4 5 4 External Locator - Top View with LCD Panel Open 1 - 5 1.Introduction 3 1. Optional Built-In PC Camera 2. LCD 3. Speakers 4. Power Button 5. Hot Key Buttons 6. LED Status Indicators 7. Keyboard 8.
Introduction Figure 2 External Locator - Front & Right side Views 1.Introduction Front Views 1. LED Power & Communication Indicators 2. 7-in-1 Card Reader 3. S/PDIF-Out Jack 4. Microphone-In Jack 5. Headphone-Out Jack M720T/M728T/M729T 1 3 4 5 2 M730T 1 2 3 4 5 Figure 3 Right Side Views 1. Optical Device Drive Bay 2. USB 2.0 Port 3. RJ-11 Phone Jack 4.
Introduction External Locator - Left Side & Rear View Figure 4 Left Side View M720T/M728T/M729T 2 1 4 3 6 5 5 M730T 1. DC-In Jack 2. RJ-45 LAN Jack 3. External Monitor Port 4. Vent/Fan Intake/ Outlet 5. 2 * USB 2.0 Ports 6. ExpressCard Slot 1 2 4 3 1 5 1.Introduction 6 5 M720T/M728T/M729T Figure 5 Rear View 1.
Introduction External Locator - Bottom View Figure 6 1.Introduction Bottom View 1. Battery (M730T 8 Cell Battery Pictured) 2. Hard Disk Bay Cover (3.5G Module Location) 3. RAM & CPU Bay Cover 4. Vent/Fan Intake/ Outlet (M730T Only) 5. Speakers (M730T Only) Overheating To prevent your computer from overheating make sure nothing blocks the vent/fan intakes while the computer is in use.
Introduction Mainboard Overview - Top (Key Parts) Figure 7 Mainboard Top Key Parts 1. Transformer 2. VT6103L 3. ExpressCard Connector 4. ENE MR510 5. KBC ITE IT8512E 1 1.
Introduction Figure 8 Mainboard Overview - Bottom (Key Parts) 1.Introduction Mainboard Bottom Key Parts 1. CPU Socket (no CPU installed) 2. Northbridge 3. Memory Slots DDR2 SO-DIMM 4. ICS 5. Card Reader Socket 6. Southbridge 7. Audio Codec 8.
Introduction Mainboard Overview - Top (Connectors) Figure 9 Mainboard Top Connectors 1 2 4 6 5 3 Mainboard Overview - Top (Connectors) 1 - 11 1.Introduction 1. Hot-key Connector 2. LCD Cable Connector 3. Keyboard Cable Connector 4. Audio Board Connector 5. Microphone Cable Connector 6.
Introduction Figure 10 Mainboard Overview - Bottom (Connectors) Mainboard Bottom Connectors 1.Introduction 7 1. BT Cable Connector 2. Multi Board Connector 3. CD-ROM Connector 4. HDD Connector 5. CMOS Bat. Connector 6. CPU Fan Cable Connector 7. DC-In Jack 8.
Disassembly Chapter 2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the M720T/M728T/M729T/M730T series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart. To make the disassembly process easier each section may have a box in the page margin.
Disassembly NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the battery is removed too). Maintenance Tools The following tools are recommended when working on the notebook PC: 2.Disassembly • • • • • • M3 Philips-head screwdriver M2.
Disassembly Maintenance Precautions The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.
Disassembly Disassembly Steps The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED. To remove the Battery: 1. Remove the battery To remove the Wireless LAN Module: page 2 - 5 1. Remove the battery 2. Remove the wireless LAN page 2 - 5 page 2 - 6 To remove the Bluetooth Module: To remove the HDD: 2.Disassembly 1. Remove the battery 2. Remove the HDD To remove the Optical Device: 1.
Disassembly Removing the Battery 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery 63 in the direction of the arrow 4 . Figure 1 Battery Removal a. Slide the latch and hold in place. b. Slide the battery in the direction of the arrow. a. 2 2.Disassembly 1 b. 3 4 3.
Disassembly Removing the Hard Disk Drive Figure 2 HDD Assembly Removal a. Locate the HDD bay cover and remove the screw(s). The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk. Hard Disk Upgrade Process 1.
Disassembly 3. 4. 5. 6. 7. Remove the hard disk bay cover 63 . Grip the tab and slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . Remove the screw 6 & 7 and the adhesive cover 68 from the hard disk 69 . Reverse the process to install a new hard disk (do not forget to replace all the screws and covers). Figure 3 HDD Assembly Removal (cont’d.) b. 3 e. 2.Disassembly 6 b. Remove the HDD bay cover. c. Grip the tab and slide the HDD in the direction of the arrow. d.
Disassembly Figure 4 Optical Device Removal a. Remove the screws. b. Disconnect the fan cable and remove the cover. c. Remove the screw. d. Push the optical device out off the computer at point 8. Removing the Optical (CD/DVD) Device 1. 2. 3. 4. 5. 6. Turn off the computer, and remove the battery (page 2 - 5). M720T/M728T/M729T: (see over for M730T) Locate the component bay cover 1 and remove screws 2 - 5 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover.
Disassembly 8. 9. 10. 11. 12. M730T: Locate the component bay cover 1 and remove screws 2 & 5 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 6 and remove the bay cover 1 . Remove the screw at point 7 , and use a screwdriver to carefully push out the optical device 9 at point 8 . Insert the new device and carefully slide it into the computer (the device only fits one way. DO NOT FORCE IT; The screw holes should line up).
Disassembly Figure 6 RAM Module Removal a. Remove the screws. b. Remove the cover. Removing the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line Memory Modules (SO-DIMM) supporting DDR2 667/800MHz. The main memory can be expanded up to 4GB. The SO-DIMM modules supported are 1024MB, and 2048MB and DDRII Modules. The total memory size is automatically detected by the POST routine once you turn on your computer. Memory Upgrade Process 2.
Disassembly 5. Gently pull the two release latches ( 7 & 8 ) on the sides of the memory socket in the direction indicated by the arrows (Figure 7c). c. d. Figure 7 RAM Module Removal (cont’d.) c. Pull the release latch(es). d. Remove the module(s). 7 9 8 2.Disassembly 6. 7. 8. 9. The RAM module(s) 9 will pop-up (Figure 7d), and you can then remove it. Pull the latches to release the second module if necessary.
Disassembly Figure 8 2.Disassembly Inverter Board Removal a. Remove the 6 screws and unsnap the LCD front panel module from the back. b. Remove the screw and discharge the remaining power from the inverter board and lift the board up slightly. c. Disconnect the cables from the inverter. d. Remove the inverter. Removing the Inverter Board 1. Turn off the computer, and remove the battery (page 2 - 5). 2.
Disassembly Removing the Processor 1. 2. 3. 4. Figure 9 Turn off the computer, and remove the battery (page 2 - 5) and the CPU/RAM bay cover (page 2 - 10). The CPU heat sink will be visible at point 1 on the mainboard. Loosen screws 2 - 4 from the heat sink in the order indicated. Carefully lift up the heat sink 5 (Figure c) off the computer. Note: a. Processor Removal a. Remove the cover and Iocate the heat sink. b. Remove the 3 screws in the order indicated. c. Remove the heat sink. 1 b. c. 2.
Disassembly Figure 10 Processor Removal Sequence 5. 6. 7. 8. Turn the release latch 6 towards the unlock symbol , to release the CPU (Figure d). Carefully (it may be hot) lift the CPU 7 up out of the socket (Figure e). Reverse the process to install a new CPU. When re-inserting the CPU, pay careful attention to the pin alignment, it will fit only one way (DO NOT FORCE IT!). d. Turn the release latch to unlock the CPU. e. Lift the CPU out of the socket. d. 6 2.Disassembly 6 Unlock Lock e.
Disassembly Removing the Wireless LAN Module 1. 2. 3. 4. 5. Figure 11 Wireless LAN Module Removal Turn off the computer, remove the battery (page 2 - 5) and the component bay cover (page 2 - 10). The Wireless LAN module will be visible at point 1 on the mainboard. Carefully disconnect cables 2 - 3 , then remove screw 4 from the module socket. The Wireless LAN module 5 will pop-up. Lift the Wireless LAN module (Figure 11d) up and off the computer. a. a. Remove the cover. b.
Disassembly Figure 12 Bluetooth Removal a. Remove the cover and locate the Bluetooth module. b. Remove the screw and disconnect the cable and seperate the connector. c. Lift the Bluetooth module out. Removing the Bluetooth Module 1. 2. 3. 4. Turn off the computer, remove the battery (page 2 - 5). The Bluetooth module will be visible at point 1 on the mainboard. Remove screw 2 and carefully disconnect the cable 3 and separate the module from the connector 4 .
Disassembly Removing the Keyboard Figure 13 1. Turn off the computer, and remove the battery (page 2 - 5). 2. Press the three keyboard latches at the top of the keyboard to elevate the keyboard from its normal position (you may need to use a small screwdriver to do this). 3. Carefully lift the keyboard up, being careful not to bend the keyboard ribbon cable (Figure 13b). 4. Disconnect the keyboard ribbon cable 4 from the locking collar socket 5 . 5.
Disassembly Figure 14 Modem Removal 2.Disassembly a. Disconnect the connectors from under the keyboard. b. Remove the screws. c. Remove the screws and disconnect the connectors from the mainboard. d. Remove the top case. Removing the Modem 1. Turn off the computer, remove the battery (page 2 - 5), HDD (page 2 - 6), component bay cover (page 2 - 10), optical device (page 2 - 8), CPU (page 2 - 13), bluetooth (page 2 - 16) and keyboard (page 2 - 17). 2.
Disassembly Remove screws 25 - 27 and disconnect the connectors 28 - 30 from the mainboard. Separate the bottom case 31 from the mainboard 32 and turn it over. Remove the screws 33 - 34 and disconnect the connector 35 from the modem. Lift the modem 37 up off the socket 36 . 6. 7. 8. 9. g. e. 25 28 26 30 33 29 34 35 Figure 15 Modem Removal Sequence 27 h. f. 37 31 32 36 31. Bottom Case 32. Main Board 37. Modem • 5 Screws Removing the Modem 2 - 19 2.Disassembly e.
2.
Part Lists Appendix A: Part Lists This appendix breaks down the M720T/M728T/M729T/M730T series notebook’s construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation. Note: Some assemblies may have parts in common (especially screws).
Part Lists Part List Illustration Location The following table indicates where to find the appropriate part list illustration. Table A- 1 Part List Illustration Location A.
Part Lists Top with Fingerprint (M720T) Figure A - 1 黑色 無鉛 白色 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 型 無鉛 型 無鉛 型 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 鋁箔 無鉛 材質 設變材質 無鉛 無鉛 Top with Fingerprint (M720T) A - 3 A.
Part Lists Top without Fingerprint (M720T) A.
Part Lists Bottom (M720T) 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 凱碩 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 Figure A - 3 Bottom (M720T) 無鉛 無鉛 無鉛 海華 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 側壁加肉 無鉛 無鉛 無鉛 拉帶加長 無鉛 無鉛 藍天3 互億 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 Bottom (M720T) A - 5 A.
Part Lists LCD (M720T) A.
Part Lists HDD (M720T) Figure A - 5 無鉛 無折切痕(設變)(無鉛) HDD (M720T) A - 7 A.
Part Lists COMBO (M720T) A.
Part Lists DVD-Dual Drive (M720T) Figure A - 7 無鉛 無鉛 無鉛 無鉛 觸點高度降低 (世華)無鉛 DVD-Dual Drive (M720T) A - 9 A.
Part Lists Top with Fingerprint (M728T) A.
Part Lists Top without Fingerprint (M728T) Figure A - 9 黑色 無鉛 無鉛 無鉛 無鉛 型 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 鋁箔 無鉛 Top without Fingerprint (M728T) A - 11 A.
Part Lists Bottom (M728T) 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 凱碩 無鉛 無鉛 無鉛 無鉛 無鉛 A.
Part Lists LCD (M728T) Figure A - 11 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 黑色 灰色 精乘 無鉛 黑色 精乘 無鉛 精乘 無鉛 無鉛 富佑鴻 無鉛 無鉛 無鉛 無鉛 無鉛 中性 電鑄薄膜鍍亮鉻 偉鎮(無鉛 無鉛 無鉛 背膠 無鉛 無鉛 LCD (M728T) A - 13 A.
Part Lists HDD (M728T) A.
Part Lists COMBO (M728T) Figure A - 13 無鉛 無鉛 無鉛 無鉛 觸點高度降低 (世華)無鉛 COMBO (M728T) A - 15 A.
Part Lists DVD-Dual Drive (M728T) A.
Part Lists Top with Fingerprint (M729T) Figure A - 15 黑色 無鉛 無鉛 無鉛 無鉛 型 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 鋁箔 無鉛 Top with Fingerprint (M729T) A - 17 A.
Part Lists Top without Fingerprint (M729T) A.
Part Lists Bottom (M729T) 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 凱碩 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 Figure A - 17 Bottom (M729T) 無鉛 無鉛 海華 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 側壁加肉 無鉛 無鉛 無鉛 拉帶加長 無鉛 無鉛 藍天3 互億 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 Bottom (M729T) A - 19 A.
Part Lists LCD (M729T) A.
Part Lists HDD (M729T) Figure A - 19 無鉛 無折切痕(設變)(無鉛) HDD (M729T) A - 21 A.
Part Lists COMBO (M729T) A.
Part Lists DVD-Dual Drive (M729T) Figure A - 21 無鉛 無鉛 無鉛 無鉛 觸點高度降低 (世華)無鉛 DVD-Dual Drive (M729T) A - 23 A.
Part Lists Top with Fingerprint (M730T) A.
Part Lists Top without Fingerprint (M730T) Figure A - 23 黑色 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 Top without Fingerprint (M730T) A - 25 A.
Part Lists Bottom (M730T) 無鉛 兩個孔徑尺寸由 改為 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 凱碩 無鉛 A.
Part Lists LCD (M730T) Figure A - 25 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 黑色 惠貿 無鉛 無鉛 黑色 惠貿 無鉛 無鉛 無鉛 黑色 惠貿 無鉛 無鉛 中性 電鑄薄膜鍍亮鉻 無鉛 無鉛 無鉛 無鉛 黑色 惠貿無鉛 無鉛 LCD (M730T) A - 27 A.
Part Lists HDD (M730T) A.
Part Lists COMBO (M730T) Figure A - 27 無鉛 無鉛 無鉛 無鉛 無鉛 COMBO (M730T) A - 29 A.
Part Lists DVD-Dual Drive (M730T) A.
Schematic Diagrams Appendix B: Schematic Diagrams This appendix has circuit diagrams of the M720T/M728T/M729T/M730T notebook’s PCB’s. The following table indicates where to find the appropriate schematic diagram. Diagram - Page Diagram - Page Diagram - Page ICH9-M 3/5 - GPIO, PWR Management - Page B - 16 Power 1.5VS, 1.05VS, 3.3V, 5V - Page B - 30 Intel Penryn (Socket-P) 1/2 - Page B - 3 ICH9-M 4/5 - Power - Page B - 17 Power 1.8V, 0.
Schematic Diagrams System Block Diagram A C- IN ,Ch ar ge r Sy st em Po we r CLEVO M720T System Block Diagram M ul ti I/ O Bo ar d VD D3 ,VD D5 14.318 MHz S PK _R, R J- 11, L ED L ID , H OT K EY, U SB , 3 G Sy ste m Me mo ry C ol ck Ge ne rat or ID T IC S9 LPR 36 3EG LF In te l Pe nr yn Pr oc es sor 64pins TSSOP B.Schematic Diagrams M 72 0T /M7 30 T Cl ic k B oa rd 17. 1*8. 1*1.
Schematic Diagrams Intel Penryn (Socket-P) 1/2 CPU ONLY SUPPORT TO 35W H _ A D S TB # 1 Y2 U5 R3 W6 U4 Y5 U1 R4 T5 T3 W2 W5 Y4 U2 V4 W3 AA4 AB2 AA3 V1 D5 C6 B4 A3 H_ S T P CL K # [ 1 3 ] H _I N TR [ 1 3 ] H _N MI [ 1 3 ] H _S M I # M4 N5 T2 V3 B2 D2 D 22 D3 F6 E Q[ 0 ] # E Q[ 1 ] # E Q[ 2 ] # E Q[ 3 ] # E Q[ 4 ] # S V D[0 1 ] S V D[0 2 ] S V D[0 3 ] S V D[0 4 ] S V D[0 5 ] S V D[0 6 ] S V D[0 7 ] S V D[0 8 ] S V D[0 9 ] B P M[ 0 ] # B P M[ 1 ] # B P M[ 2 ] # B P M[ 3 ] # P RD Y # P R E Q# TC K T DI
Schematic Diagrams Intel Penryn (Socket-P) 2/2 VCO R E V C OR E V C OR E B.
Schematic Diagrams Cantiga 1/6 - Host U15A R 213 100_1%_04 75_1%_04 H_D#0 H_D#1 H_D#2 H_D#3 H_D#4 H_D#5 H_D#6 H_D#7 H_D#8 H_D#9 H_D#10 H_D#11 H_D#12 H_D#13 H_D#14 H_D#15 H_D#16 H_D#17 H_D#18 H_D#19 H_D#20 H_D#21 H_D#22 H_D#23 H_D#24 H_D#25 H_D#26 H_D#27 H_D#28 H_D#29 H_D#30 H_D#31 H_D#32 H_D#33 H_D#34 H_D#35 H_D#36 H_D#37 H_D#38 H_D#39 H_D#40 H_D#41 H_D#42 H_D#43 H_D#44 H_D#45 H_D#46 H_D#47 H_D#48 H_D#49 H_D#50 H_D#51 H_D#52 H_D#53 H_D#54 H_D#55 H_D#56 H_D#57 H_D#58 H_D#59 H_D#60 H_D#61 H_D#62 H_D#63 R2
Schematic Diagrams Cantiga 2/6 - VGA, CRT 1.
Schematic Diagrams Cantiga 3/6 - DDR S A _D S A _D S A _D S A _D S A _D S A _D S A _D S A _D M_ 0 M_ 1 M_ 2 M_ 3 M_ 4 M_ 5 M_ 6 M_ 7 S A _D S A _D S A _D S A _D S A _D S A _D S A _D S A _D QS _ 0 QS _ 1 QS _ 2 QS _ 3 QS _ 4 QS _ 5 QS _ 6 QS _ 7 S A_ DQ S A_ DQ S A_ DQ S A_ DQ S A_ DQ S A_ DQ S A_ DQ S A_ DQ S #_ 0 S #_ 1 S #_ 2 S #_ 3 S #_ 4 S #_ 5 S #_ 6 S #_ 7 S A _ MA _ 0 S A _ MA _ 1 S A _ MA _ 2 S A _ MA _ 3 S A _ MA _ 4 S A _ MA _ 5 S A _ MA _ 6 S A _ MA _ 7 S A _ MA _ 8 S A _ MA _ 9 S A _ M A
Schematic Diagrams Cantiga 4/6 - Power 1.
Schematic Diagrams Cantiga 5/6 - Power 1. 0 5 V S 10mils 3 . 3V S _A T V D A C H C B 10 0 5K F -12 1 T 20 1 . 0 5V M_ D P L L A C 61 6 C3 9 4 C 39 3 4 . 7 U _ 6 . 3V _ X 5 R _ 0 6 0. 1U _1 0 V _ X7 R _ 0 4 0 . 0 1U _ 16 V _ X7 R _0 4 C 41 7 C4 1 5 10 U _6 . 3 V _ X5 R _ 0 8 10mils 0 . 1 U _ 10 V _ X 7R _ 04 C 61 7 C3 8 9 C 39 0 4 . 7 U _ 6 . 3V _ X 5 R _ 0 6 0. 1U _1 0 V _ X7 R _ 0 4 0 .
Schematic Diagrams Cantiga 6/6 - GND U1 5 J A M3 6 AE3 6 P3 6 L 36 J 36 F36 B3 6 A H3 5 AA3 5 Y3 5 U3 5 T 35 BF3 4 A M3 4 A J 34 AF3 4 AE3 4 W34 B3 4 A3 4 B G3 3 B C3 3 BA3 3 AV3 3 A R3 3 A L 33 A H3 3 AB3 3 P3 3 L 33 H3 3 N3 2 K3 2 F32 C3 2 A3 1 A N2 9 T 29 N2 9 K2 9 H2 9 F29 A2 9 B G2 8 B D2 8 BA2 8 AV2 8 A T 28 A R2 8 A J 28 A G2 8 AE2 8 AB2 8 Y2 8 P2 8 K2 8 H2 8 F28 C2 8 BF2 6 A H2 6 AF2 6 AB2 6 AA2 6 C2 6 B2 6 B H2 5 B D2 5 BB2 5 AV2 5 A R2 5 A J 25 A C2 5 Y2 5 N2 5 L 25 J 25 G2 5 E2 5 BF2 4 A D1 2 A
Schematic Diagrams DDRII CHANNEL A SO-DIMM 1 JDIMM_1 Terminator [6 ] M_ A _ A [ 1 4: 0 ] M_ A B S 2 [ 6 ] M_ A B S 0 [ 6 ] M_ A B S 1 [ 5 ] M_ C S #0 [ 5 ] M_ C S #1 [ 5 ] M _C LK _ D D R 0 [ 5] M_ C L K _ D D R # 0 [ 5 ] M _C LK _ D D R 1 [ 5] M_ C L K _ D D R # 1 [ 5 ] M_ C K E 0 [ 5 ] M_ C K E 1 [ 6 ] M_ A _ C A S # [ 6 ] M_ A _ R A S # [ 6 ] M _A _ W E # R 28 R2 7 1 0 K _ 04 10 K _ 04 [ 1 1, 1 5 , 18 ] [ 1 1, 1 5 , 18 ] [ 6] M _ ABS2 M _ ABS0 M _ ABS1 M _ CS # 0 M _ CS # 1 M _ CK E 0 M _ CK
Schematic Diagrams DDRII CHANNEL B SO-DIMM 2 La yo ut no te : JDIMM_2 is placed farther from the GMCH than JDIMM_1 B.
Schematic Diagrams Panel, Inverter, CRT 5V S D Q2 6 2N 70 0 2W S D A C_ HS Y NC G CRT _ HS Y N C D CRT _ V S Y N C 1 K _ 04 D3 1 C A S D 75 1 V A 3 . 3V S 2 . 2 K _0 4 3. 3 V S D A C _ D D C A D A TA S R1 9 1 2 . 2 K _0 4 R1 8 9 2 .
Schematic Diagrams ICH9-M 1/5 - SATA R TC V C C 1 K _ 04 A R 94 1M _0 4 R 96 33 2 K _ 1% _ 06 I C H _I N T V R M E N 8 52 0 5 -02 0 0 1 I C H _ I N T V R ME N B 22 A 22 RT CV C C C 45 3 R2 5 8 0 . 1 U _ 1 6V _0 4 2 4 .
Schematic Diagrams ICH9-M 2/5 - PCIE, PCI, USB Boot BIOS Strap SPI 01 Stuff PCI 10 No stuff Stuff 11 No stuff No stuff LPC(default) R1 4 8 1 K_ 0 4 No stuff [2 0 ] [2 0 ] [ 20 ] [ 20 ] P C I _ G N T #0 Stuff R1 3 2 * 1K _0 4 P CIE _ RX N3 _ 3 G P C I E _ R X P 3 _3 G P C I E _ TX N 3 _ 3 G P C I E _ TX P 3 _3 G [ 2 3 ] P C I E _ R X N 4 _L A N [ 2 3 ] P C I E _ R X P 4_ L A N [ 2 3 ] P C I E _T X N 4 _L A N [ 2 3 ] P C I E _T X P 4_ L A N Disable P C I E _ T X N 1 _C P C I E _ T X P 1
Schematic Diagrams G P I O1 3 SW I# P M _ S Y S R S T# L A N _P W R 8 7 6 5 1 2 3 4 G P I O6 0 S B _B A T L OW # S B _B L O N A C _ P R E S E N T _R [ 1 0 , 1 1, 1 8 ] [ 1 0 , 1 1, 1 8 ] I C H _ S MB C L K 0 I C H _ S MB D A T 0 [2 0 ] [2 0 ] I C H _ S MB C L K 1 I C H _ S MB D A T 1 NEW CARD, MINI CARD [2 6 ] [ 1 9] P C IE _ W A K E # 1 0 K _0 4 R 3 45 * 10 K _ 0 4 P W R_ B T N# R 3 03 1 0 K _0 4 IC H_ S M B DA T 1 R 3 08 1 0 K _0 4 IC H_ S M B CL K 1 R 3 09 * 10 0 K _ 04 G P I O2 4
Schematic Diagrams ICH9-M 4/5 - Power U23 F 0. 1U_10V_X7R_04 0.1U_10V_X7R_0 4 10U_10V_08 AE1 CLOSE TO ICH9M 1 0m ils V5REF 1 0m ils V5REF_SUS VCC1_5_ B L52 HCB1608KF- 121T25 1A 1.5VS C189 0. 1U_10V_X7R_04 0.1U_10V_X7R_0 4 C209 C21 0 C202 100U_6. 3V_B2 10U_1 0V_08 10 U_10V_ 08 0.1U_10V_X7R_0 4 A C206 D29 10_04 ASD751V C R328 V5REF C547 C546 1U_16V_X5R_06 0.1 U_10V_ X7R_04 VCCSATAPL L L11 HCB1005KF- 121T20 10 mi ls 1.5VS C598 10 U_10V_ 08 1U_6.3V_04 C23 0 C243 1U_ 6.
Schematic Diagrams ICH9-M 5/5 - GND VSS_ NCTF[1 ] VSS_ NCTF[2 ] VSS_ NCTF[3 ] VSS_ NCTF[4 ] VSS_ NCTF[5 ] VSS_ NCTF[6 ] VSS_ NCTF[7 ] VSS_ NCTF[8 ] VSS_ NCTF[9 ] VSS_N CTF[10 ] VSS_N CTF[11 ] VSS_N CTF[12 ] 3. 3V C27 2 14 *0.1 U_1 6V_04 1 [15 ,26 ] R SMRST# 3 2 SLP_S3# SUSB# [ 20, 23, 26, 27,2 9] R10 9 *10mil_sh ort SU SC # [ 26] 3. 3V 14 SL P_ S4# SYS_PWROK 9 1. 8V_PWRGD 10 U 8C 7 4LVC08 PW 8 SB_ PW ROK [ 15] R 154 C26 7 *1 0K_04 *0.1 U_1 6V_04 7 [15 ] 3.
Schematic Diagrams Clock Generator CLOCK GENERATOR Layout note: 3 .3 VS Insatlled: Differential clock level is higher 3 .
Schematic Diagrams Multi I/O, ODD, CCD, BT, TPM SATA ODD TPM 1.2 Layout Note SATA SINGAL FROM SB TO JODDB1 END OF JODD1 FOR M720T [ 1 8] J _O D D _ 7 3 S1 S2 S3 S4 S5 S6 S7 S A T A _ TX P 1 S A T A _ TX N 1 S A T A _ TX P 1 S A T A _ TX N 1 S A T A _ RX N1 S A T A _ RX P 1 P1 P2 P3 P4 P5 P6 S A T A _ RXN1 S A T A _ RXP 1 O D D _ D E T E C T# 1 2 3 4 5 6 7 8 9 10 11 12 [1 3 ] [ 13 ] [1 3 ] [ 1 3] 5 VS TO SB GPIO O D D _ D E T E C T# [1 5 ] 1.
Schematic Diagrams New Card, Mini PCIE 3 .3 VS C 4 46 *0 . 1 U _ 1 6V _ 0 4 5 NEW CARD B U F _ P L T_ R S T # 1 4 2 3 .3 V U1 9 0 . 1U _1 6 V _ 04 21 A U XI N P E R S T# 3 .3 VS C4 4 3 C4 4 2 0 . 1U _1 6 V _ 04 0 . 1U _1 6 V _ 04 C4 4 1 C4 4 5 0 . 1U _1 6 V _ 04 0 . 1U _1 6 V _ 04 A U XO U T 6 5 3 .3 V IN 3 .3 V IN 1 .5 VS [ 1 7 , 23 , 2 6, 2 7 , 2 9] 2 23 B U F _P L T _R S T# B U F _P L T _R S T# [ 14 ] U S B _ OC # 4 1 .5 V IN 1 .
Schematic Diagrams LED, FAN, TP, FP, USB LED V D D3 V DD3 3. 3 V S FAN CONTROL 3 .3 V S 5V S 22 0 _0 4 3 L E D_ A C IN# L E D_ P W R # [ 26 ] [ 1 9, 2 6 ] D1 9 Z 2 1 12 F A N _ D C _ V OL _R F A N _D C _ V OL B W LA N _E N R 2 44 1 0 K _1 % _0 4 [ 2 0 , 26 ] Q 7 DT C1 1 4 E UA 3 + 2 - 1 Z 21 1 5 G U 1 6A LM 35 8 L 10 U _1 0 V _0 8 D2 0 R B 5 5 1V - 30 Q 20 A O3 4 09 J_ F A N 1 30mils E E C4 3 8 30mils R 2 43 4 .
Schematic Diagrams JMB385 Card Reader JMB385 CARD READER 02/12 3. 3V S 3 .3 V S _ CA R D R4 0 3 4 . 7K _ 0 4 S D _ CD# R3 1 0 4 . 7K _ 0 4 M S _ INS# R3 3 1 1 0K _ 0 4 SD W P# R3 4 3 1 0K _ 0 4 M D I O 13 R3 3 5 1 0K _ 0 4 M DIO 7 R3 5 3 2 00 K _ 0 4 M D I O 12 R3 3 9 2 00 K _ 0 4 M D I O 14 3 .3 V S _ CA R D 0 _0 6 40mil 40mil 3 .3 V S_ CAR D V C C_ CA R D M D I O 12 DV1 .8 V 3 .3 V S _ CA R D S D / MS C L K R 38 4 2 2 _ 04 3 .
Schematic Diagrams PCI-E LAN RTL8111C LA N _ V D D 3 R4 0 0 60mil 3. 3V Q2 9 *2 N 70 0 2 W S R4 1 2 C 64 4 *3 3 0K _0 4 * 0. 1 U _1 6 V _ 04 *A O 3 40 9 D LA N _ V D D 3 R 4 13 G L A N _P W R G [1 5 ] 60mil 0_ 0 4 Q2 8 S M A 1 /E E DI R4 5 3.
Schematic Diagrams Audio Codec ALC662 Layout Note: C los e t o cod ec pi n 3 8 Layout Note: Clo se to co dec p in 25 3 . 3V S 3. 3 V S _ A U D L 38 5 V S _A U D C 5 06 C5 1 4 C 2 36 C 23 7 0. 1 U _ 1 6 V _0 4 1 0U _1 0 V _0 8 0. 1 U _ 1 6V _0 4 0 . 1 U _ 1 6V _ 0 4 C 5 75 C 56 7 C5 7 0 0. 1 U _1 6 V _0 4 1 0 U _ 1 0V _ 0 8 0 . 1 U _ 1 6V _ 0 4 1 0U _ 10 V _ 08 R3 1 2 5 6 8 10 11 A Z _ S DIN0 _ R 3 3 _0 4 E A P D _ MO D E 47 S P DIF O BEEP A UDG R 1 17 4 7K _ 0 4 R 1 16 4 .
Schematic Diagrams Audio AMP2056 5 VS 5 C 642 *0 . 1 U _ 1 6 V _ 0 4 [2 4 ] 5V S 1 CO DE C_ E A P D # 4 2 U2 8 *7 4 A H C 1 G0 8 G W C 518 3 [ 2 6] 0_ 0 4 R3 1 5 *0 _ 04 S Y S M U T E A MP # 1 0 0K _0 4 1 MU T E A M P # 4 2 U 24 7 4 A H C 1 G 0 8G W A U D _ A Z _R S T # C5 3 9 0 .1 U_ 1 6 V _ 0 4 C 245 C2 5 6 C2 5 8 C5 2 0 * 0 . 1 U _ 1 6 V _ 04 0. 1 U _ 16 V _ 0 4 0. 1 U _ 16 V _ 0 4 0.
Schematic Diagrams KBC-ITE IT8512E L 10 H C B 1 0 0 5K F -1 2 1 T2 0 R2 9 4 V D D3 V DD 3 C4 7 0 C 1 86 C 1 78 C 2 20 C1 8 8 C1 8 5 C 18 0 10 U _1 0 V _0 8 0. 1 U _ 1 6 V _0 4 0. 1 U _ 1 6 V _0 4 0 . 1 U _ 1 6V _ 0 4 0. 1 U _1 6 V _0 4 *0 . 1 U _ 1 6V _ 0 4 * 0.
Schematic Diagrams System Power, LED BKLT 5VS,3.3VS S Y S 15 V 6A 3A 1 00 K _ 04 PR9 7 SU SB 4 D P R 1 54 3A 1 M_ 04 P Q2 4 2 N 7 00 2 W G 5 VS 1 M_ 0 4 PC1 0 1 PC1 0 4 P R9 5 0 . 1U _1 6 V _ 04 *1 0 U _ 10 V _ 08 10 0 K _0 4 SUSB PQ 2 5 2 N 7 0 0 2W G S US B P C 1 05 PR9 1 0 .
Schematic Diagrams Power VDD3, VDD5 VDD3,VDD5 V IN 35mil E SYS5 V 25mil P C1 8 8 5mil B V IN 2 + 0 . 1 U _ 25 V _ X 7R _0 6 LD O5 V *1 5 U _ 2 5V _ D 2 A P C1 9 4 P D2 2 P C1 9 3 P R 17 1 F M0 5 4 0-N 4 . 7U _ 6. 3 V _ X5 R _0 6 F M0 54 0 -N 0 . 1U _ 10 V _ X7 R _0 4 * 1M _0 4 22 19 T G2 P R1 5 7 *1 0 _0 6 0 . 1U _ 10 V _ X7 R _0 4 14 4 PL 9 2. 5 U H _ 6. 8 *7 . 3 *3 .
Schematic Diagrams Power 1.5VS, 1.05VS, 3.3V, 5V 1.05VS 5V A V IN P C 90 P C 21 9 P R 2 05 0 . 0 1U _ 16 V _ X7 R _ 0 4 2 0 P _5 0 V _ 04 2 4 . 9 K _1 % _0 6 4 DL P D 25 4 F M5 82 2 17 PAD P C 2 14 + 2 2 0U _ 4V _ D P C 2 15 + 15 14 16 D H N.C P C 2 17 0 . 1U _ 16 V _ 04 1U _1 0 V _ 06 1.5V 5V PC1 5 4 V1 .8 P R1 5 1 3 .3 V 35mil [ 1 7] P R1 4 8 5V 1 0 K _0 4 5 9 7 1 0 0K _ 0 4 P R1 4 9 G GN D P C 1 52 P C 1 59 P C 16 0 10 0 0P _5 0 V _X 7 R _ 04 0.
Schematic Diagrams Power 1.8V, 0.9VSM 1.8V,0.9VSM 5V V 1 .8 P R 39 P R4 7 1 M_ 0 4 10 _ 0 6 1 0 0 P _5 0 V _ 0 4 2 . 2K _1 % _ 0 4 1 U _1 0 V _ 0 6 1U _ 10 V _ 0 6 2 9 Rb 10 5 PC 5 3 P C 48 P R 42 1 U_ 1 0 V _ 0 6 *0 . 0 6 8 U _ 1 0V _0 4 0 _ 06 PC 4 2 1 0 00 P _ 5 0 V _ X7 R _0 4 VS SA 1U _ 1 0V _ 0 6 DL 4 12 13 V 1 .8 PR 4 0 P C5 5 P C6 7 2 0 K _ 1% _ 0 4 4 . 7U _ 6.
Schematic Diagrams Power VCORE VCORE VI N 5V A V -R C 1 P D1 1 1 00 0 P _ 50 V _ X 7R _ 04 F M0 5 4 0-N 1 U _ 1 0V _ 0 6 P R2 4 BST1 P Q3 6 I R F 7 4 13 Z P B F * 0_ 0 4 P C2 3 D P R S L_ S T P E N_ V CO RE DP RS L 10 0 _ 1% _ 0 4 *1 0 0P _5 0 V _ 04 *1 00 P _ 5 0V _ 0 4 C 5 6 7 8 P C 13 0 + * 33 0 U _ 2 . 5V _D 3 P C 12 3 + *3 3 0 U _ 2. 5 V _ D 3 P C1 3 1 + 33 0 U _ 2 . 5V _D 3 P C 12 4 + 3 3 0U _ 2. 5 V _ D 3 A 2 3 1 T G2 BG 2 1 00 P _ 5 0V _0 4 0_06 PC5 9 P C2 0 0.
Schematic Diagrams Power AC-IN, Charger AC IN & CHARGER P R1 0 5 * 10 m i _l s ho rt VA P Q 35 A S P 8K 10 S F D 5 T B 2 1 7 PR 9 9 0 . 1U _ 50 V _ 06 4 . 7 U _ 25 V _ X 5R _0 8 1 0 K _ 08 P R1 0 1 3 0 _0 4 P C1 4 2 0 0 K _1 % _0 4 1 0K _ 1 % _0 4 P R7 0 _0 4 PR 5 P R 1 17 P Q 35 B S P 8 K 1 0S F D 5 TB 4. 7 U _ 2 5 V _X 5 R _ 0 8 BAT V _B A T PF2 5A P C 11 4 4. 7 U _2 5 V _X 5 R _0 8 P C 10 8 P C1 1 3 4 . 7 U _ 2 5V _ X 5 R _ 0 8 0. 1 U _ 5 0 V _0 6 4 P C 1 06 0 .
Schematic Diagrams Multi I/O Board 1/2 For M720T SPEAKER LID SWITCH HOT KEY & POWER SWITCH SW8 SW6 M J_S PK R_7 2 MS W 2 T JG -5 33 -S -V -T / R 1 2 3 4 1 M 3. 3 V 1 2 1 8 82 6 6-0 2 00 1 P C B F o o t p rin t = 88 2 66 -2 L M C1 7 MC 16 1 8 0P _ 5 0V _ 0 4 1 80 P _ 50 V _ 0 4 M U1 2 1 MGN D M3 . 3 V S POWER SWITCH LED M 3 . 3V S HDD/ODD LED 5 6 3 4 3 1 3 MS W 3 T JG -5 33 -S -V -T / R 2 4 M3 . 3V S NUM LOCK LED SW2 1 3 MC 19 0 .
Schematic Diagrams Multi I/O Board 2/2 3G/Raboson M C2 1 1 50 U _ 6 . 3V _V 20 mil [3 3 ] 1 3 5 7 9 11 13 15 M P CIE _ W A K E # M R8 MW L A N _ C LK R E Q# *0 _0 4 [ 3 3 ] M C L K _P C I E _ MI N I _ 3 G# [ 3 3 ] M C L K _P C I E _ MI N I _ 3 G MJ _3 G1 W AKE # B T _ DA T A B T _ CH CL K C LK R E Q# G ND0 R E F CL K R E F CL K + G ND1 3. 3 V _ 0 GN D 5 1. 5 V _ 0 U I M_ P W R U I M _D A TA U I M _C LK U I M _R E S E T U I M _V P P MC 3 2 4 6 8 10 12 14 16 0 .
Schematic Diagrams Finger Printer Board Finger Printer F 3 .3 V 1 1 2 3 4 4 FJ_FP1 FJ _ FP1 F US B _ P P 1 F U S B _ P N1 F T C_ VD D F G P I O0 / I N T FR 19 1 . 5 K _ 04 F U S B _ P P 1 _R FR 21 2 7 .
Schematic Diagrams Click Board CLICK BOARD C J_TP1 CJ_T P1 CGND CTP_DATA CTP_CL K 1 CJ_ TP2 1 2 3 4 CJ _TP2 4 1 12 8520 1-04 051_ R CG ND 6-2 0-94A2 0-112 CGND Sheet 36 of 40 Click Board CSW 1~2 2 1 LIFT KEY 4 3 RIGHT KEY 1 3 C GND CH1 9 8 7 6 1 CTPBU TTON_ R CH4 2 3 4 5 MTH2 37D9 1 CG ND CTPBU TTON_ L C TPBU TTON_ R C GND 2 3 4 5 For M720T CSW2 TJG-5 33-S- V- T/R 2 4 5 6 CTPBU TTON_ L 5 6 CSW1 TJG-5 33-S- V- T/R 1 2 3 4 1 9 8 7 6 2 3 4 5 MTH23 7D91 CGND C H3 1 9 8 7 6
Schematic Diagrams M730T ODD Bridge Board B.Schematic Diagrams M730T ODD BRIDGE BOARD Sheet 37 of 40 M730T ODD Bridge Board BJ_SATA1 S1 S2 S3 S4 S5 S6 S7 P1 P2 P3 P4 P5 P6 BSATA_R XN 1 BSATA_R XP1 BGND BODD _D ETEC T# 1.
Schematic Diagrams M730T Audio Board M730T AUDIO BRIDGE BOARD AJSPDIF1 ASPDIFO AL4 *FCM1005KF- 102T02 AC1 *0.
Schematic Diagrams Power Sequence Diagram M720T V0.0 BOOT BLOCK DIAGRAM 9 PW R_ SW # 1 13 M ULT I I/ O BO AR D ? ? ? ? ? ? CL _P WR OK DE LA Y_ PW RG D NORTH BRIDGE B.Schematic Diagrams Cantiga V DD 3/ VD D5 VR LT C3 85 0 EC Sheet 39 of 40 Power Sequence Diagram DD _O N 3 5V 3 2 DR AM V R I TE 85 12 E S C4 86 DE LAY DD _ON 75 ms 3 .3 V PW R_ BT N# 4a PM _R SM RS T# 4b SU SC # 5a SU SB # 5b 1 .8 V 3 0 .
Schematic Diagrams Power Sequence v3.0 M720T V3.0 POWER ON SEQUENCE 560ms 1 PWR_SW# 2 DD_ON 3 5V 3 V5REF_SUS 3 3.3V 3 1.8V 164.7ms 370us 515.4us 568.0us 6.215ms 4a RSMRST# 4b PWR_BTN# 206.4ms 120.8ms 85.6ms Sheet 40 of 40 Power Sequence v3.0 174.4ms 5a SUSC# 5b SUSB# 61.10us 365.6us 6 5VS 6 V5REF 6 3.3VS 6 1.05VS 6 0.9VSM 6 1.5VS 371.5us 482.8us 690.8us 1.5912ms 3.932ms 7 8 920us 9 ms CL_PWROK 107.6ms 10 VCORE_ON 11 VCORE 12 VRM_PWRGD 1.17V 2.
B.
