World-Class Auto Security TM bULLET Owner’s Manual
Table of Contents Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Using Your Bullet Security System . . . . . . . . . . . . . . . . . . . . . . . . 3 Premier™ 4-Button/8-Channel Remote Controls . . . . . . . . . . . . . . . 3 How to Interpret the Chirps and Parking Light Flashes . . . . . . . . . . . 4 How to Interpret the LED Status Indicator . . . . . . . . . . . . . . . . . . 4 Headlight Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Features ● FACT™ — False Alarm Control and Test — eliminates recurring false alarms ● Lifetime Warranty ● $3,OOO Theft Protection Guarantee (see guarantee card for details) ● A pair of Premier™ 4-Button/8-Channel Remote Controls with more than 4 billion digital codes ● AntiScan™ — blocks electronic scanners from disarming the alarm ● Multiple-Car Control — allows you to command several alarms with the same remote ● MultiRemote™ Recognition — useful for other drivers, since the system will ac- cep
Using Your Bullet Security System Premier™ 4-Button/8-Channel Remote Controls The Premier 4-button/8-channel remote control is a miniature radio transmitter with a range of up to 100 feet. Obstructions, interference or a weak battery will reduce the range. Your remote control is the key to your security system. You will use it to arm or disarm the system, lock or unlock the doors, activate its panic feature or control options such as a remote trunk release or IntelliStart™ remote engine starter.
As noted on the previous page, button II can control yet another option when the system is disarmed. If you have one of the following options installed, pressing button II while the alarm is disarmed will either: TO ACTIVATE AN OPTION WHEN THE ALARM IS DISARMED . . . . . . . ★ Remotely open the trunk OR . . . ★ Remotely open the fuel-filler door. TO ACTIVATE AN OPTION REGARDLESS OF ALARM STATE . . . . .
Secured Valet Mode Whenever the alarm is put in secured valet mode, all of the alarm functions are bypassed since it prevents AutoArming and accidental activation of the alarm. You should use the valet mode whenever your car is either to be serviced by mechanics, handed over to car wash personnel or driven by valet attendants. It also comes in handy if you ever lose your remote control or its battery dies.
Smart AutoTesting™ Each time you remotely arm your vehicle, it will perform a series of tests on all triggers and sensors. If a trigger malfunction is found, you will be visually and audibly alerted immediately with 4 chirps and flashes instead of the usual 2. If a sensor is malfunctioning, you will receive the usual 2 chirps and flashes, then, a few seconds later, there will be 4 chirps and flashes.
FACT™— False Alarm Control and Test With FACT, you’ll never experience repeated false alarms. If your six-sound siren goes off, DO NOT remotely disarm the system while the siren sounds; allow it to run for the full siren duration. Before sounding the siren a second time, the system automatically checks for another activated trigger. Should the siren sound again, you will know for sure that someone is tampering with your vehicle. (To disable FACT, see User-Selectable Features on pages 9-10.
AntiScan Car thieves use electronic scanners that rapidly transmit one remote control code after another to defeat ordinary alarms. AntiScan prevents scanners from disarming your system. Automatic Fault-Proof Starter Interrupt The system automatically prevents engine starting while the system is armed but allows you to start it even in the unlikely event of a full system failure (other manufacturer’s alarms may leave you stranded).
User-Selectable Features Your Bullet vehicle security system allows you to set many of its features to your own personal preferences. We have made the programming procedures very simple: to make a change, you just flick the valet switch a few times. The system comes from the factory with all of its features pre-programmed as noted in the table below and on page 10. To change any of the settings, use the procedure noted. To restore the feature to its factory setting, just repeat the procedure: 1.
Feature # of Factory flicks & setting chirps Secondary action Program completion confirmation Result Siren Duration 30 sec.
User-Programmable Remote Controls Your system will respond to as many as four remote controls regardless of each remote control’s individual digital coding. Thus, you can buy additional remote controls, including the super-high-security 4.3-billion-code Premier™ remote controls, from any Authorized Clifford Dealer. To add a new remote control to the system, use the procedures noted in the User-Selectable Features section on pages 9-10.