Owner`s manual

ManualsBrandsClifford ManualsAutomotiveCONCEPT 10

Standard Features of the Concept 600

The Clif ford Con cept 600 sys tem is de signed to be in stalled in any vehicle with a 12-volt batt ery.

Con cept 600/299 1

¨ Thatcham-Evaluated

¨ Lifetime Warranty

¨ Up to £500 AntiTheft Guarantee

¨ His & Hers Remote Controls

¨ ACG™ 2 (Anti-CodeGrabbing™)

¨ Superheterodyne Extended Range Receiver

¨ Audible Low-Battery Warning

¨ Digital Tilt/Motion Sensor

¨ Com pletely Auto mat ic Self- Adjusting

¨ Built-In Two-Point AutoImmobiliser™

¨ Wireless FuelGuard™

¨Electronically Programmable Proximity Sensor

¨ Patented UltraSecure Coded Valet Mode™

¨ Built-In Window RollUp

¨ Easy Window RollUp Bypass

¨ Enhanced User-Selectable AutoArming

¨ AutoArming Enable/Disable

¨ AutoArm & Lock

¨ Visual Indication

¨ Instant AutoArm Bypass

¨ User-Selectable Remote Valet Mode Entry/Exit

¨ Remote Keyless Entry and Accessory Activation Even in

Valet Mode

¨ Eight-Event TotalRecall™

¨ Built-In BlackJax Anti-Carjacking System

¨ True Carjack Protection

¨ Safe & Intelligent Engine Shutdown

¨ Immediate Vehicle Recovery

¨ Ensuring Immobilisation

¨ Sabotage-Proof Operation

¨ Optional DataPort™ Interface and CliffNet Wizard Pro™

Software

¨ Point-and-Click Feature Programming

¨ Complete System Diagnostics At-A-Glance

¨ Self-Powered SmartSiren 4

¨ Automatic Low Siren Battery Warning

¨ FACT — False Alarm Control and Test

¨ Remote Panic with Smart Locking/Unlocking

¨ Integrated Electronic Timer

¨ Remote Headlight Activation Capability

¨ Remote Door Locking/Unlocking with Built-in Relays

¨ User-Selectable AutoLock

¨ User-Selectable AutoUnLock

¨ Built-In Dual Indicator Light Flasher with Onboard Relay

¨ Remote-Controlled Courtesy Lighting

¨ Smart Remote Boot Release

¨ Patented Smart AutoTesting™

¨ Patented Malfunction AutoBypass™ with

AutoReMonitoring

¨ Patented Smart Prior Intrusion Attempt Alert

¨ Patented Remote Control Code Learning and

MultiRemote Recognition

¨ Clear All Remotes

¨ Multiple-Car Control

¨ High-Luminescence LED Status Indicator with Automatic

Battery-Saving Mode

¨ Multiple Sensor/Trigger Inputs

¨ Patented SmartPowerUp™ 2

¨ Full-Time SecureAccess™ Programming

¨ Dual Ground Lines

¨ Advanced CMOS Microcomputer

¨ Pre-Loomed Wiring

¨ Three Accessory Outputs with Selectable Output Types

¨ AutoActivation of Accessory Output B

¨ Installer-Selectable Door Ajar/Delayed Courtesy Lights

¨ Prewired LED, Sensor, Siren, Extended Range Receiver,

and PlainView 2 Switch Connectors

Summary of content (20 pages)

PAGE 1
Standard Features of the Concept 600 The Clifford Concept 600 system is designed to be installed in any vehicle with a 12-volt battery.
PAGE 2
System Components The Concept 600 kit contains the following components: One Prewired 24-pin Connector Harness One Prewired 14-pin Connector Harness One Concept 600 Control Unit with Stainless Steel Enclosure One Electronically Programmable Proximity Sensor One Digital Tilt/Motion Sensor One Wireless FuelGuard Two Remote Transmitters One Superheterodyne Extended Range Receiver One LED Status Indicator One PlainView Coded Valet Switch 2 One Self-Powered SmartSiren 4 One Hardware Kit One Owner’s Manual One W
PAGE 3
Concept 600/299 3
PAGE 4
Wiring Description for the 14-Pin Connector Pin Colour Connects to 1 2 3 6 7 8 9 10 Brown Blue/White Brown White/Orange White/Green Red/White Brown/Red Grey Indicator light output Brake output Indicator light output Door unlock common Door lock common Indicator and brake light input Interior light input (+ or -) Door trigger input (+ or -) Inputs 11 12 13 14 Red/Orange Red/Green Grey/Green Grey/Orange Door unlock normally open Door lock normally open Door lock normally closed Door unlock normally cl
PAGE 5
Concept 600/299 5
PAGE 6
Passenger Compartment Connections (Continued) LED Status Indicator Select a prominent location on the dash or console visible through all windows. Discuss placement with the owner. 1. Verify there is adequate space to accommodate the LED, then drill a 5/16” (8mm) hole and route the wires through it. 2. Mate the LED connectors to the VIOLET and BLACK wire connectors as shown in the diagram on page 5. 3. Remove the adhesive backing and press the switch into place. PlainView Coded Valet Switch 2 1. 2. 3. 4.
PAGE 7
Passenger Compartment Connections (Continued) Brake Switch The brake switch connection is required for the operation of the Concept 600’s anti-carjacking electronics. 1. Turn the ignition to the “ON” position and press the brake pedal to verify that the brake lights are operational. 2. Find the one wire that carries +12V when the brake pedal is pressed, then connect the BLUE/WHITE wire to this wire. Indicator Lights See the Indicator Lights section in this binder.
PAGE 8
Engine Bay Connections RPM Monitoring This is required for both RPM-activated automatic door locking and for BlackJax anti-carjacking features. See the RPM Monitoring section in this binder for information. Self-Powered SmartSiren 4 The control unit and siren utilise two-way digital signal transmissions to maintain a constant communication link.
PAGE 9
Delayed Courtesy Lights Some vehicles have a courtesy light delay or dimming circuit, which interferes with an alarm being able to detect the door trigger upon remote arming. If the delay or dimming lasts more than 5 seconds, no special connections or testing are needed, simply turn on the Delayed Courtesy Lights feature as noted in the Installer-Programmable Features section on page 15.
PAGE 10
Master Remote Control Channel Assignments Function Press Button Function 1 Arm/Disarm 9 Remote Valet 2* Activate Auxilliary A Output (usually remote boot release)* 10 Proximity Sensor Override 3 Silent Arm/Disarm 11* Unassigned or IntelliStart 4 Features (Low Temp/Low Battery AutoStart or Manual Transmission SafeStart)* 4* IntelliStart 4 Accessory* (IntelliStart 4 not evaluated by Thatcham) 12* Unassigned* 5* Unassigned* 13* Unassigned* 6* SmartWindows 4 Accessory* 14* Unassigned*
PAGE 11
Sensor Adjustment (Continued) Electronically Programmable Proximity Sensor (Continued) Since any metal objects above or near the Proximity Sensor will have a significant impact on operation, warn your customer never to place coins, CDs, cassettes (due to the iron oxide tape) or other metallic objects above or near where the sensor is mounted. 1. 2. 3. 4. Turn off any fluorescent lights that may interfere with the sensitivity testing of the Concept 600’s radar sensor.
PAGE 12
Sensor Adjustment (Continued) Dual-Zone OmniSensor Adjustment (Continued) n To adjust sensitivy of the warning zone: q To change the sensitivity of the warning zone, press button 3 (you’ll hear 1 chirp). q To make a new sensitivity setting, press button 2. You will hear 2 chirps. q Thump the car lightly with your fist, you will hear one chirp. q Press button 4, you will hear two chirps. q You may now test sensitivity by thumping lightly with your fist. You should hear one chirp.
PAGE 13
Certificate of Installation/Ownership/Operation After installation and testing has been completed, you must fill in the Clifford Electronics “Certificate of Installation/ Ownership/Operation.” Once you have filled in all the information required on the form, be sure that the customer signs and dates the certificate. See step 18 in the System Checklist & Troubleshooting section for instructions on distributing the form.
PAGE 14
User-Programmable Features User-Programmable Features (1 Chirp = OFF, 2 Chirps = ON) Feature Select Unmarked 1 Unmarked 2 Unmarked 3 Unmarked 4 ✱1 AutoProgram New Master Remote NOTE 1 Chirps (Off/LoudChirps/QuietChirps) (1 chirp/2 chirps/3 chirps) AutoArming (On/Off) Arm/Disarm with Secondary Remote NOTE 5 ✱2 NOT USED NOT USED AutoArm & Lock (On/Off) Boot Release with Secondary Remote NOTE 6 ✱3 NOT USED Remote Valet Feature (On/Off) NOT USED Silent Arm/Disarm with Secondary Remote NOTE 6
PAGE 15
Installer-Programmable Features To access the installer-programmable features, use the procedure defined in the User-Programmable section, but in step 4, hold and press the ✱ side of the PlainView 2 Switch for 10 seconds. You will hear three confirmation chirps indicating that the system is in installer-program mode.
PAGE 16
System Checklist & Troubleshooting (Continued) Step 2. Test the AutoImmobilisation and Wireless FuelGuard circuits. n Turn the ignition to the “ON” position and start the engine. Let the engine run for at least 10 seconds, then turn the ignition “OFF.” After 30 seconds have passed, the dual AutoImmobilisation circuits will engage (indicated by a slow flash of the LED). Turn the ignition to the “ON” position.
PAGE 17
System Checklist & Troubleshooting (Continued) q If the Proximity Sensor is indicated, check the mounting location and sensitivity setting as noted in the Sensor Adjustment section on pages 10 and 11. If one of the trigger points is indicated, check pin switch operation and check for shorts in the trigger line. q If the tilt sensor is indicated, check the mounting location and, if necessary, cut the small black wireloop (see diagram on page 3) to enable the two-minute arming delay.
PAGE 18
System Checklist & Troubleshooting (Continued) Step 6. Test the power windows. Arm the system by pressing button 1 on the remote control. n Power windows close. This is the correct response, proceed to step 7. n Power windows do not close. If the power windows do not close, disarm and rearm the system (the one-time Window RollUp Bypass feature may have been activated--arming and rearming will deactivate it). Make sure the Window RollUp feature has been programmed using the chart on page 15.
PAGE 19
System Checklist & Troubleshooting (Continued) Step 11. Test the boot trigger circuit. Arm the system, then use the key to unlock the boot. n Siren sounds immediately, indicator lights flash repeatedly. This is the correct response, proceed to step 12. (You can silence the siren by pressing button 1 on the remote control or disarm by pressing button 1 two times.) n Alarm does not sound immediately.
PAGE 20
System Checklist & Troubleshooting (Continued) Step 18. Distribute all necessary paperwork including: n Certification of Installation/Ownership/Operation. q The White copy if for the customer/insurer. q The Blue copy is for the VSIB/insurer. q The Pink copy must be sent to Clifford Electronics at the address noted on the certificate. q The Green copy is for the dealer/installer. n Owner’s Manual must be given to the customer. n Wireless FuelGuard Location Record. q One copy is for your records.