Owner`s manual

Sen sor Ad just ment (Con tin ued)
Electronically Programmable Proximity Sensor (Continued)
Since any metal ob jects above or near the Prox im ity Sen sor will have a sig nifi cant im pact on op era tion, warn
your customer never to place coins, CDs, cas settes (due to the iron ox ide tape) or other me tal l ic ob jects above
or near where the sen sor is mounted.
1. Turn off any fluorescent lights that may interfere with the sensitivity testing of the Concept 600’ s radar sensor.
2. Disarm the system with the remote control.
3. Transmit channel 16 on the master remote (LevelShift three times, then button 4). You will hear one chirp and the LED will turn on.
4. Test the Proximity Sensor’s primary zone by rapidly leaning through an open window into the passenger compartment. You will
hear a siren chirp when the primary zone is triggered. This should not occur near the window, but i nstead when you would be in a
position to touch the car stereo.
To change the sensitivity of the primary zone, press and release button 2 to increase sensitivity or button 4 to decrease
sensitivity.
To rapidly increase or decrease several steps, press and hold the button. For each sensitivity incr ease, you will hear a higher and
higher pitched confirmation chirp. For each sensitivity decrease, you will hear a lower and lower p itched confirmation chirp. Two
LoudChirps indicate minimum and maximum settings of the 32-step range of settings. You may now pres s button 3 to adjust the
warning zone, or press button 1 to fully exit the Proximity Sensor adjustment mode (you will hear 3 chirps).
To change the sensitivity of the warning zone, press button 3
(you’ll hear 1 chirp). Then use the same procedure as above, but this
time, rapidly bring your hands and face to the window as a thief would to see what’s inside. The se nsitivity of the warning zone
should be set so that it is triggered when your face and hands are within a few inches of the windo w, no further. When done, press
button 1 to reselect the primary zone (you will hear 2 chirps), then button 1 again to fully exit Proximity Sensor adjustment mode
(you will hear 3 chirps).
5.Repeat the preceding steps as required. An improperly adjusted sensor will cause the Concept 600 to false alarm or not respond
properly to a genuine threat. Keep in mind that you may need to reposition the sensor, possibly af ter the customer has had the
system for several days.
Re mote-Con trolled Over ride of Each Prox im ity Sen sor Zone
Transmitting channel 10 at anytime from the remote whilst the system is armed will override the war ning zone of the Proximity
Sensor. This prevents the system from sounding warnings if the vehicle must be parked in an area wi th heavy pedestrian traffic. A
second transmission of channel 10 anytime afterward whilst the system is still armed will override both zones of the Proximity Sensor.
This comes in handy when a pet or a passenger must be left in the vehicle. The channel 10 warning z one override is visually
confirmed with 4 flashes of the indicator lights. A second channel 10 transmission to override both
zones is confirmed with four more
flashes. The sensor zones are automatically restored the next time you arm.
Optional Dual-Zone OmniSensor Adjustment
Our optional Dual-Zone OmniSensor uses digital signal processing to detect vibration and/or impact to the vehicle. If a thief were to
break a window or cause any impact to the vehicle, the primary zone of this sensor would trigger th e full alarm. However, if a thief
brushed against the vehicle a warning tone would sound.
1. Disarm the system with the remote control.
2. Transmit channel 15 on the master remote (LevelShift three times, then button 3). You will hear one chirp and the LED will turn on.
n
To adjust sensitivity of the primary zone:
q To change the sensitivity of the primary zone, press and release button 2. You will hear 1 chirp.
q To make a new sensitivity setting, press button 2. You will hear 2 chirps.
q Thump the car firmly with your fist, you will hear one chirp.
q Press button 4, you will hear two chirps.
q You may now test sensitivity by thumping the vehicle firmly with your fist. You should hear one ch irp.
q At this point, you can:
Press button 2 to make another new setting for the primary zone (you will hear two chirps).
Press button 1 to exit (you will hear three chirps).
Press button 3 to adjust the warning zone (see instructions on the next page).
Con cept 600/299 11