Owner`s manual

Installer-Programmable Features
To access the installer-programmable features, use the procedure defined in the User-Programmable s ection, but in step 4, hold and
press the ✱ side of the PlainView 2 Switch for 10 seconds. You will hear three confirmation chirps indicating that the system is in
installer-program mode.
Table of Installer-Programmable Features (1 chirp = OFF, 2 chirps = ON)
Fea ture
Select
Unmarked 1 Unmarked 2 Unmarked 3
✱ 1
Single/Double Lock Pulse
(1 chirp/2 chirps)
Accessory Output Timer
Duration
(10 seconds )
See NOTE 1
Door Ajar Warning /Delayed
Courtesy Lights
(1 chirp/2 chirps)
✱ 2
Single /Double Unlock Pulse
(1 chirp/2 chirps)
Auxiliary A Type
(Pulsed /Timed/Latched)
(1 chirp /2 chirps/3 chirps)
Auxiliary A Interlock
(On/Off)
✱ 3
Lock/Unlock Pulse
3 second/1 second
(1 chirp/2 chirps)
Auxiliary B Type
(Pulsed /Timed/Latched)
(1 chirp /2 chirps/3 chirps)
Auxiliary B Interlock
(On/Off)
✱ 4
AutoActivate Auxiliary B upon
Remote Arming
(On/Off)
Auxiliary C Type
(Pulsed /Timed/Latched)
(1 chirp /2 chirps/3 chirps)
Auxiliary C Interlock
(On/Off)
✱ 5
Program RPM
See
Mandatory RPM Programming
Diesel Engine/Petrol Engine
(1 chirp/2 chirps)
(For IntelliStart 4 only*)
Program Window RollUp or
SmartWindows 4
See NOTE 2
✱ 6
Aux il iary Si ren Out put
(Constant/Pulsed)
(1 chirp/2 chirps)
NOT USED NOT USED
*IntelliStart 4 not evaluated by Thatcham
n
NOTE 1: Once this feature is selected, one chirp is provided to indicate that the timer has started . You can set this anywhere
from one second to four minutes. When the desired duration has been reached, press the unmarked side of the PlainView 2
switch. The system responds with two chirps to confirm the new system timer duration.
n
NOTE 2: To program the Window RollUp feature, first roll down the windows using the switches located insid e the vehicle.
Next, access unmarked 3, marked 5. The system responds with one chirp and then rolls the windows u p automatically. Wait
10 seconds, the system will provide a two-chirp confirmation and the programming is complete.
System Checklist & Troubleshooting
The fol low ing check list and trou ble shoot ing tips will as sure that you have in stalled the Co ncept 600 cor rectly. If the sys tem does not
re act as noted, fol low the trou ble shoot ing tip(s) de noted with a black box be low that item, then re peat the step. Each suc ces sive step
re quires that the pre vious step has been com pleted as in di cated.
The Clifford Wizard simplifies the troubleshooting process by providing system diagnostic informati on in a graphical format. All
system settings are provided at-a-glance, and adjustments to the system settings can be made with a click of a mouse. This reduces
the amount of time required for performing the following tests.
Step 1.
Re- enable the cour tesy lights.
In step 1 of the Important Information sec tion in this binder, the in te rior cour tesy lights were disabled. You must now re-enable
the courtesy lights by re placing the fuse you re moved or re set the cour tesy light switch back t o its nor mal “DOOR” po si tion bef ore
pro ceed ing.
Con cept 600/299 15