Owner`s manual

System Checklist & Troubleshooting (Continued)
Step 2.
Test the Auto Im mo bi li sa tion and Wire less FuelGuard cir cuits.
n
Turn the ignition to the “ON” position and start the engine. Let the engine run for at least 10 se conds, then turn the ignition
“OFF.” After 30 seconds have passed, the dual AutoImmobilisation circuits will engage (indicated b y a slow flash of the LED).
Turn the ignition to the “ON” position. The en gine should not re spond (it should nei ther start nor crank, nor should the fuel
pump ac ti vate).
q Engine does not respond. This is the correct response, proceed to the next AutoImmobilisation test.
q Engine starts or cranks. Check the power and ground connections, then check to see if starter/ig ni tion/fuel pump or
im mo bi li sa tion cir cuits have been mis wired. Care fully re test the ve hi cle wires as noted in the Starter and Ig ni tion
Auto Im mo bi li sa tion Cir cuits section on page 7. Be sure the ignition input/output is correct!
n
Arm the Concept 600 (either from inside or outside the vehicle) and wait 10 seconds. Turn the ignit ion “ON.”
q Engine does not respond. This is the correct response, proceed to the AutoImmobilisation test.
q Engine starts or cranks. The starter/ig ni tion/fuel pump or im mo bi li sa tion cir cuits have been mis wired. Care fully r e test the
ve hi cle wires as noted in the Starter and Ig ni tion Auto Im mo bi li sa tion Cir cuits section on page 7. Be sure the ignition
input/output is correct!
q Engine still starts or cranks after retesting all the wiring as noted on page 7, check the power and ground connections.
Then make sure the fuses are in the fuseholders, verify the control unit connectors are securely fa stened, verify the ignition
input and output wires are connected to the true ignition line instead of a 12V or accessory line, and verify that the
transmitters are programmed correctly.
n
Test the Wireless FuelGuard by disarming the Concept 600, turning the ignition “ON” and cranking th e engine.
q Engine starts and runs for up to one minute. This is the correct response, proceed to step 3.
q Engine starts, then stops running after several seconds. The Wireless FuelGuard needs to be synchronized. If the system
does not disarm properly, refer to step 8.
o Locate the Wireless FuelGuard.
o Press down firmly on the top of the Wireless FuelGuard and hold. You should feel the top of the en closure move inward
slightly as you apply pressure.
o Whilst you are pressing the top of the Wireless FuelGuard enclosure, have someone start the engine. Release the top of
the FuelGuard once the engine has successfully started.
o After 30 seconds have passed, turn OFF the engine.
q Engine starts, then stops running after several seconds after all the above tests are performed. Test the wiring in/out
and ground.
Step 3.
Test the chirps.
Close all doors and arm the Concept 600 by pressing button 1 on the remote control.
n
2 Chirps: This is the correct response. Proceed to step 4.
n
1 Chirp: The Concept 600 had previously AutoArmed itself passively and by pressing button 1, the system dis armed. Remote
disarming is indicated with one chirp and one indicator light flash.
n
4 Chirps: If you hear 4 chirps ei ther im me di ate ly or 5-10 sec onds af ter the ini tial two chirps, a tri g ger or sen sor is open or
active, or the ve hi cle has de layed cour tesy lights and the De layed Cour tesy Lights fea ture has not been programmed on. Dis arm
with the re mote con trol, en ter the ve hi cle and turn on the ig ni tion. The LED will flash 1–10 times, pause, then re peat the same
number of flashes (the flash cy cle re peats five times for your con ven ience). Ref er to the foll owing chart.
LED flashes Trig ger/sen sor in di ca tion
1 flash Electronically Programmable Proximity Sensor
2 flashes Optional OmniSensor
3 flashes Digital Tilt/Motion Sensor
4 flashes* Door Trigger*
5 flashes Boot Trigger
6 flashes Bonnet Trigger
7 flashes An attempt was made to turn the ignition “ON” or start the engine whilst the system was armed
8 flashes More than three consecutive incorrect valet codes were entered whilst the system was in BlackJax mo de
9 flashes BlackJax Activation
10 flashes Power Interruption
* If the de layed cour tesy lights fea ture is ac ti vated, this trig ger/sen sor in di ca tion will not be pro vided.
16 Con cept 600/299