Electric Fireplace Model No.: □ IF-50FSB □ IF-60FSB □ IF-70FSB CONSUMER SAFETY INFORMATION Read this manual before installing and operating this appliance. Failure to follow these instructions may result in electric shock, fire property, or personal injury. Do not store or use gasoline or other flammable liquids in the vicinity of this appliance. Service contact: service@alipuinc.
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
ALWAYS mount to wall bracket before use. DO NOT set on the floor, or other surface, to use. NEVER use a wall mount bracket from another manufacturer. This product is not intended to be a primary heat source. It is for supplemental heat only. INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock! Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ALWAYS turn this heater off before unplugging it from the outlet.
You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape measure; electric drill; 1/4” wood drill bit, hammer. PARTS & HARDWARE B. Wood Screws (11pcs) C. Wall Anchors (11pcs) D. 4x8mm Screws (2pcs)l E. Wall Bracket F. Metal Bracket H.Remote Control I. Log Set . J.Decorative Crystals Left free standing leg Fixed on back of firebox A.
PRODUCT DIMENSIONS Model Number A B C D E F G IF-50FSB 50" 127.0cm 17.7" 45.0cm 5.6" 14.2cm 48.7" 123.8cm 16.3" 41.5cm 12.2" 30.9cm 46.0" 116.8cm IF-60FSB 60" 152.4cm 17.7" 45.0cm 5.6" 14.2cm 58.7" 149.2cm 16.3" 41.5cm 12.2" 30.9cm 56.0" 142.2cm 72" 17.7" 45.0cm 5.6" 14.2cm 70.7" 179.7cm 16.3" 41.5cm 12.2" 30.9cm 68.0" 172.7cm IF-70FSB 182.9cm Installation and Assembly Your appliance is a wall-mounted, recessed and /or mantel installed appliance.
RECESSED TO WALL INSTALLATION ( Tips:Wall bracket removing is NOT required. ) STEP 1 Select a dry wall to open a hole for fireplace box. Figure (A) Figure (A) Hole cut size Size of hole as below chat-Framing Hole Size Framing Hole Size Model Number W H D IF-50FSB 48.7"(123.8cm) 16.3"(41.5cm) 5.98"(15.2cm) IF-60FSB 58.7"(149.2cm) 16.3"(41.5cm) 5.98"(15.2cm) IF-70FSB 70.7"(179.7cm) 16.3"(41.5cm) 5.98"(15.2cm) STEP 2 Remove two screws on both sides of the fireplace at front corner.
STEP 3 Take off the front tempered glass of the fireplace. Figure (D) Figure (C) Figure (D) TEP 4 Take foam out of the fireplace.
Figure (E) STEP 6 Have two people to move the fireplace box to the wall hole or fireplace mantel.
Figure(G) STEP 7 Put carbon log or crystal stone to bed. Figure (H) Figure(H) STEP 7 Place the front panel lock the appliance.
Figure(I) WALL MOUNTED INSTALLATION Due to many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. STEP 1 Select a location that is not prone to moisture and is located at least 36"(914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper, etc. STEP 2 Have two people hold the appliance against the wall to determine the final location.
Figure(b) STEP 4 Take the glass panel out of the fireplace box. Place it in a soft and clean place. Figure (c) STEP 5 Take foam(A) out of the fireplace.
Figure (d) STEP 6 Mark out location, then mount the bracket(part e) onto the wall using the supplied screws. This bracket MUST have the hooks facing upward and be level. Figure(e) Figure(e) NOTE: It is strongly recommended that the mounting bracket(part e) be screwed into the wall studs where possible. If the wall studs cannot be used, ensure that the supplied plastic anchors are used to affix the bracket to the wall and the bracket is adequately secured.
Fasten the metal bracket (F) at the back of fireplace with 2pcs of 4x8mm screws, the other end to the wall with 1pc of drywall anchors. STEP 7 With the wall mounting bracket installed have two people lift the appliance up and insert the two hooks on the bracket into the two slots on the back of the appliance. STEP 8 Put carbon log or crystal stone to bed, place the front panel lock the appliance by 4x8mm screws.
Free Standing Option Lay the heater on the floor or a table Install the base with 6pcs screws ( screws is on the bottom of the fireplace) as provided
LOG-SET/CRYSTAL EMBER INSTALLATION (Note: Please make the installation according to the embers which you bought or selected.) * Glass front must be removed and the appliance must be mounted in its final location before the logset/crystal embers are installed. * If your fireplace come with log-set, remove the log-set from the package, put it to the fireplace designed place.
WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure do to so could result in electric shock, fire, serious injury, or death. POWER Make sure the ON/OFF switch, located on the control panel, is in the OFF position.Plug the power cord into a 110-120V Volt 12 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3).Make sure the outlet is in good condition and that the plug is not loose.
Turn on switch button first BUTTON POWER FUNCTION ON: Enables control panel functions and remote control.Turn on flame effect. OFF: Disables control panel functions and remote control. Turn off flame effect. 1. Press once. Indicator light turns on. Power turns on. All functions enabled. 2. Press again. Indicator light turns off. Power turns on. All functions will off. COLOR button: Makes the color flame effect changing. 1. Press once. Flame color effect gets changing. 2.
3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If there are, use a vacuum to clean the vent areas. 4. With the POWER switch in the OFF position, plug the power cord back into the outlet. 5. If the problem continues, have your outlet and wiring inspected by a professional. Remote Control Battery Information With 2x AAA batteries. NOTE: Remote control battery used depends on the remote control type which selected above. NEVER dispose of batteries in fire.
Electrical and Moving Parts: The fan motors are lubricated at the factory and will not require lubrication. Electrical components are integrated in the fireplace and are not serviceable by the consumer. Storage: Store heater in a clean dry place when not in use. WARNING! No other servicing should be performed by the consumer. Do not attempt to service the unit yourself. Troubleshooting WARNING DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE.
Remote control does not work. 1. Replace batteries in remote control. 1. Low batteries. 2. Aim control at sensor located 2. Not aiming control correctly. directly behind glass screen in center 3. Defective remote control and of unit just above logs. /or sensor. 3. Replace remote control and/or sensor.
