OME2208061
11 21 1 2 10 11 4 9 15 8 23 19 17 3 7 24 6 22 12 13 16 18 5 14 20 12 13 13 K 350mm K1 A B 49PCS C 49PCS 8*40 36PCS L LED K2 D 1PCS 3.5*14 48PCS E 4PCS 3.
1 2 1950*424 1PS 1950*440 1PS 6 3 1950*424 1PS 9 7 140*400 1PS 8 295*424 1PS 13 15 20 19 295*424 1PS 12 11 140*400 1PS 640*324 1PS 350*100 1PS 1918*424 1PS 10 14 18 5 140*400 1PS 140*400 1PS 350*60 3PS 4 100*424 2PS 17 16 640*324 1PS 22 1850*60 2PS 662*172 1PS 23 593*100 1PS 24 334*60 1PS 21 350*100 1PS 100*300 1PS 603*344 1PS 1928*149 1PS 1928*149 1PS
Ｈａｒ ｄｗａｒ ｅ ｉ ｎｓｔ ａｌ ｌ ａｔ ｉ ｏｎ ｄｅｍｏｎｓｔ ｒ ａｔ ｉ ｏｎ ＮＯＴＥ： Ｐｌ ｅａｓｅ ｍａｋｅ ｓｕｒ ｅ ＂Ａ＂ｈａｒ ｄｗａｒ ｅ ｔ ｉ ｇｈｔ ｅｎｅｄ ａｎｄ ｃａｎ＇ ｔ ｂｅ ｐｕｌ ｌ ｅｄ ｏｕｔ ！ Ⅰ Ⅲ Ⅱ Ⅳ Scan QR code f or assembl y vi deo
① A A A A A A A A 1 A C A A 2 A A A A A A 4 A A A A A C A A C A A 3 A A A A A A A A C C A C 12 A C X2 C A A*39 C*12 C put A on board put C on board 1 2 3 4 12 4 12
② C 9 A C C C C C A 21 10 C A 11 6 C C A C A C X2 7 D C 8 C D C D K1 DC K1 5 C 13 C C C X3 D A A 17 A K1 D A A A 16 A*10 C*24 D*4 K1*2 put A on board put C on board 5 6 16 17 5 6 7 8 9 10 11 13 21
③ 10 G B B 9 G G 8 4 G G B 7 B 10 Make sure the arrow on the screw align to the hole on the side.
④ 10 6 8 4 9 7 10 24 6 G 5 8 4 9 3 7 G 5 G G G G G G G G*8
⑤ B 12 B B 13 B Make sure the arrow on the screw align to the hole on the side.
⑥ 11 G G 21 G G G 2 11 G 1 G B B B B 11 21 2 B 11 B*6 G*6 B B Make sure the arrow on the screw align to the hole on the side.
⑦ 6 10 23 4 9 3 5 B 1 10 B 6 4 B 9 B 3 B B 5 Make sure the arrow on the screw align to the hole on the side.
⑧ F D D D D D 1 D 4 3 5 14 D*24 F*4 F F 15
⑨ 19 B 22 B B 20 B 18 16 E B B E E E B 17 22 18 18 E E 16 17 22 16 D K2 1 B*6 D*4 E*4 K2*2 16 K2 D 15 5 14
⑩ H 1 21 23 24 6 H*20 I*20 H I I
11 D J 1 23 24 LED 6 D*16 J*16 LED
12 L 1 15 16 5 L*4 14
LED Light If you can’t let the lights work successfully, please check the following: 1. Please check the direction of the connect, try it in the opposite direction, according to the following picture. 2. Please check the remote control, it need you to tear down the plastic septum before use it. 3. Don’t let the remote control too far from the receiver, make sure there is no obstruction between them.
