Assembly Instructions Caution: You must read this before you proceed Please look in the support bar for hardware packs. Table Caution: This Table is NOT a TOY Keep your child/children at bay during the assembly process. Whenever moving/lifting the Table and to prevent damage to the Table, two adults are needed to execute these actions.
Parts List Label Picture Description QTY A Side Table Top 2 B Center Table Top 1 C End Table Top 2 D Table Top Support Bar 4 E First Leg 2 F Second Leg 2 First Leg Support Bar Second Leg Support Bar G H 2 1 Hardware Label ① ② ③ ④ ⑤ ⑥ Picture Description Bolt (M8x40mm) Bolt (M8x25mm) Screw (M6x45mm) Screw (M6x50mm) Washer (M8.
Assembly Preparation Before Beginning Assembly: x 17 x 17 x5 x 33 x 29 Noble House Home Furnishings LLC Page 3 of 10
Assembly Steps Overview Center Table Top (B) Side Table Top (A) End Table Top (C) Second Leg (F) First Leg (E) Second Leg Support Bar (H) First Leg Support Bar (G) FRONT FACING This Table has multiple parts and may require up to 45 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 A B Place Side Table Tops(A) and Center Table Top(B) facedown onto a clean, non-marring surface. Then align them as pictured. Step 3 C 6 A 4 A C Place the End Table Tops(C) as pictured above. Attach End Table Top(C) to Side Table Tops(A) using Screws( ④) with Allen Wrench(⑥) as pictured above. Do not fully tighten the Screws.
Step 4 C 6 A 3 5 A C Attach End Table Top(C) to Side Table Tops(A) using Screws( ③), and Washers(⑤) with Allen Wrench( ⑥) as pictured above. Do not fully tighten the Screws. Step 5 C 6 A 1 A C B Attach End Table Tops(C) to Side Table Tops(A) and Center Table Top(B) using Bolts(①)with Allen Wrench( ⑥ ) as pictured above.
Step 6 6 D A 4 A B Attach Table Support Bars(D) to Side Table Tops(A) and Center Table Top(B) using Screws(④) with Allen Wrench(⑥ ) as pictured above. Do not fully tighten Screws. Step 7 C 6 E 2 5 Attach First Leg(E) to End Table Top(C) using Bolts( ②), and Washers(⑤) with Allen Wrench(⑥) as shown in the picture above. Repeat the same process with the remaining First Leg(E) and Second Legs(F). Do not fully tighten the Bolts.
Step 8 G F E E F 1 6 5 Attach the First Leg Support Bar(G) to First Leg(E) and Second Leg(F) using Bolts(①), and Washers(⑤) with Allen Wrench(⑥) as shown above. Repeat the same process with the remaining First Leg Support Bar(G). Do not fully tighten the Bolts. Step 9 G H 6 2 5 Attach Second Leg Support Bar(H) to First Leg Support Bar(G) using Bolts(②), and Washers(⑤) with Allen Wrench(⑥) as pictured above. Do not fully tighten the Bolts.
Step 10 Stand the Table up, with assistance from your adult partner. Exert pressure oorwards, onto the Table with both your hands. This pressure will help the Legs and Table Top reach full alignment status. Check for wobbles on a LEVEL surface. If no wobbles are found proceed to tighten the Bolts and Screws in a sequential manner, until evenly secured. When tightening the Bolts and Screws tighten sequentially. Do not tighten any Bolt or Screw fully and then move on towards the next one.
Care & Maintenance ● Prolonged exposure to rain may cause rusting which can stain oors. ● Do not put hot items directly on furniture surface. ● Do not clean furniture with harsh cleansers or polish. ● To obtain the longest lifespan of your outdoor products, minimizing exposure to direct sunlight is recommended. ● Children should not climb or jump on the furniture. ● Do not write on furniture without a padded barrier to protect the surface.
