Operation Manual
AIR
CONDITIONER
FEATURES
OPERATING
INSTRUCTIONS
1
MODE select
button
E LE CT RONI
C C
ONT
ROL
OP E R ATI
NG
INS T RUCT I ONS
Before you begin, thoroughly familiarize yourself with the control panel and remote controller
and all its functions, then follow the symbol for the functions you desire.
The unit can be controlled by the unit control panel alone or with the remote controller .
NOTE: This manual does not include Remote Controller Operations, see the <<Remote
Controller Instruction>> packed with the unit for details.
OPERATION PANEL OF THE AIR CONDITIONER
4
1
Power indicator
Selects the appropriate operating mode.
Each time you press the button, a mode
is selected in a sequence that goes
from
COOL, FAN and DRY .The mode indicator
light illuminates under the different mode
setting.
NOTE: On above modes, the unit operates
the
auto fan speed automatically. You can
set fan speed only by the remote controller on
COOL and FAN modes.
2
UP( ) and DOWN( )
button
Used to adjust (increasing/decreasing)
temperature settings in 1
O
C/2
O
F(or 1
O
F) increments
in a range of 17
O
C/62
O
F to 30
O
C/88
O
F (or 86
O
F).
NOTE:
The control is capable of
displaying
temperature in degrees Fahrenheit or
degrees
Celsius. To convert from one to the other,
press
and hold the Up and Down buttons at the
same
time, for 3
seconds.
3
ON-OFF
button
Power switch
on/off.
Operating Instructions
COOL
operation
- Press the "MODE" button until the "COOL"
indicator light comes on. The unit will operate
the auto fan speed automatically.
- Press the ADJUST buttons "
▲
" or " " to
select your desired room temperature. The
temperature can be set within a range of
17
O
C-30
O
C/62
O
F-88
O
F(or 86
O
F).
- Press the "FAN" button on the remote
controller to choose the fan speed.
DRY
operation
- Press the "MODE" button until the "DRY"
indicator light comes on.
- Under this mode, you cannot select a
fan
speed or adjust the
temperature.
- Keep windows and doors closed for the
best
dehumidifying
effect.
- Do not put the duct to
window.
FAN
operation
- Press the "MODE" button until the "FAN "
indicator light comes on. The unit will operate
the auto fan speed automatically. The
Fig.3
2
light
2
3
Timer mode indicator
light (set only by remote
controller)
4
LED
Display
Shows
the set
temperature
while on cool mode.
While on
DRY
and FAN
modes,
it
shows
the room
temperature.
Error
codes:
E1-
Room temperature sensor
error-
Unplug the unit and plug it back
in.
If error repeats, call for
service.
E2-
Evaporator temperature sensor
error-
Unplug the unit and plug it back
in.
If error repeats, call for
service.
E4- Display panel
communication
error-
Unplug the unit and plug it back
in.
If error repeats, call for
service.
Protection
codes:
P1-
Bottom tray is full - Connect
the
drain hose and drain the
collected
water away. If error repeats,
call
for
service.
temperature cannot be adjusted on fan mode.
- Press the "FAN" button on the remote
controller to choose the fan speed.
- Do not put the duct to window.
SLEEP
operation
This feature can be activated from the
remote control ONLY.
To activate SLEEP feature, the set
temperature
will increase by 1
O
C/2
O
F(or 1
O
F) in 30
minutes.
The set temperature will then increase
by
another 1
O
C/2
O
F(or 1
O
F) after an additional
30
minutes. This new temperature will be
maintained
for 7 hours before it returns to the
originally
selected temperature. This ends the Sleep
mode
and the unit will continue to operate as
originally
programmed.
NOTE:
This feature is unavailable under FAN
or
DRY
mode.
6
7
MODE select
button