Specifications

ManualsBrandsClimateMaster ManualsConsumer electronicsATC32U01 iGate

Tranquility

Digital

Quick Start Guide

Table of Contents

Step Title Page

1 Thermostat Conﬁ guration 3

Staging 3

Auxiliary Heat 3

Programming 3

2 System Conﬁ guration 4

Airﬂ ow Selection 4

Option Selection 4

Unit Conﬁ guration 4

Pump Conﬁ guration 5

Valve Conﬁ guration 5

3 Accessory Conﬁ guration 5

Air Filter 6

Humidiﬁ er 6

UV Lamp 6

Air Cleaner 6

Step Title Page

4 Input Dealer Information 6

5 Humidity Conﬁ guration 6

6 Temperature Algorithm 6

7 Demand Reduction Conﬁ guration 7

8 Unit and System 8

Pre-Start Checklist

9 Unit Start-up Procedure 8

97B0107N01

Residential Packaged and Split

DIGITAL Geothermal Heat Pumps

With iGate™ and vFlow™ Technology

Rev.: 5 Dec., 2012B

Summary of content (10 pages)

PAGE 1
Tranquility® Digital Quick Start Guide 97B0107N01 Residential Packaged and Split DIGITAL Geothermal Heat Pumps With iGate™ and vFlow™ Technology Rev.: 5 Dec.
PAGE 2
This page was intentionally left blank.
PAGE 3
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 ClimateMaster Digital units are shipped from the factory with default values for key parameters such as air flow and water flow settings. The unit will operate with these default settings, however, the installer may wish to customize these settings to better match installation conditions. This guide will walk the installer through those settings. More detail is available in the unit IOM.
PAGE 4
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 Step 2 System Configuration Use System Configuration to adjust critical equipment settings. The System Configuration information will be automatically obtained from each communicating control in the system.
PAGE 5
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c .
PAGE 6
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 AIR FILTER This feature displays an alert to remind the user to change the air filter after the selected time has passed. Adjust the Air Filter Reminder settings using the up/down arrow buttons. Press the center button to save changes.
PAGE 7
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 Step 7 Demand Reduction Configuration Users may wish to take advantage of the Demand Reduction feature where utility companies offer special rates for demand reduction, or simply to save energy during certain time periods. Demand Reduction is activated by an input signal at the unit control board to reduce the electric load while peak utility rates are high.
PAGE 8
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 Start-Up Guide Step 8 Unit and System Pre-Start Check List Internal Flow Controller: Verify that it is purged of air and in operating condition. Low water temperature cutout: Verify that low water temperature cut-out controls are set properly (LT1 JW3). Miscellaneous: Note any questionable aspects of the installation.
PAGE 9
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 to provide a water seal. e. Turn thermostat to “OFF” position. A hissing noise indicates proper functioning of the reversing valve. INSTALLER SETTINGS THERMOSTAT CONFIG SYSTEM CONFIG ACCESSORY CONFIG INPUT DEALER INFO HUMIDITY CONFIG TEMPERATURE ALGORITHM DEMAND REDUCTION CNFG SERVICE MODE RESTORY DEFAULTS 7. Allow five (5) minutes between tests for pressure to equalize before beginning heating test. a.
PAGE 10
Tr a n q u i l i t y ® D i g i t a l Q u i c k S t a r t G u i d e R e v. : 5 D e c . , 2 0 1 2 Revision History Page # 5 Dec. 12 4 1 Oct., 12 4, 5 Unit Config, vFlow Pump Config Sections Updated 8 May, 12 All First Published Description TES, TEP and TAH Digital Information Added R AI BR I HE AT P U M P S A TO NE WATER TO IFIED TO ARI A RT S C CE NG WITH LYI MP O IR MANUFACT UR ER Date IS ST AND 3 ARD 1 -1 R O 25 6 ISO 9001:2008 Certified Quality: First & Always 7300 S.W.