System information

C0240111-06-07-GB
49
4 TABLE OF MASKS W3000 base
Mask Description Para n°
level1 | level2 | level3
OFF
OFFOFF
OFF
Main display mask. Indicates the state of the unit ("ON", "OFF").
>MODE
>MODE>MODE
>MODE
The submask displays the operating mode of the unit
> > CH
> > CH> > CH
> > CH
"CH"=Chiller, "HP"= Heat Pump
>ST
>ST>ST
>ST
The submask displays the operating status of the unit
> > ON
> > ON > > ON
> > ON H
HH
H
"ON K"= on from keypad, "ON D"= on from digital input, "ON B"= on from time bands, "ON
S"= on from supervisor, "OFFA"= off from alarm, "OFFS"= off from supervisor, "OFFB"= off
from time bands, "OFFD"= off from digital input, "OFFK"= off from keypad, "OFF"= off
>REQ
>REQ>REQ
>REQ
The submask displays the percentage of power requested by the thermoregulator
> > 50
> > 50 > > 50
> > 50
value ranging from 0 to 100
>ACT
>ACT>ACT
>ACT
The submask displays the percentage of power delivered by the thermoregulator
>
> >
> > 50
> 50 > 50
> 50
value ranging from 0 to 100
>PUMP
>PUMP>PUMP
>PUMP
The submask displays the time remaining before the pump is switched on/off.
> > 60
> > 60 > > 60
> > 60
If the time decreases the unit is in the switching on/off phase.
The time is expressed in
seconds.
>EVIN
>EVIN>EVIN
>EVIN
The submask displays the inlet temperature of the evaporator
> > 12.5
> > 12.5 > > 12.5
> > 12.5
temperature expressed in degrees centigrade
>EVO1
>EVO1>EVO1
>EVO1
The submask displays the outlet temperature of evaporator 1
> > 07.2
> > 07.2 > > 07.2
> > 07.2
temperature expressed in degrees centigrade
>EVO2
>EVO2>EVO2
>EVO2
(If 2 evaporators are present). The submask displays the outlet temperature of evaporator 2
> > 06.9
> > 06.9 > > 06.9
> > 06.9
temperature expressed in degrees centigrade
>CDIN
>CDIN>CDIN
>CDIN
The submask displays the inlet temperature of the condenser (only for water/water
units if
the condenser inlet probe is enabled)
> > 24.3
> > 24.3 > > 24.3
> > 24.3
temperature expressed in degrees centigrade
>CDO1
>CDO1>CDO1
>CDO1
The submask displays the outlet temperature of condenser n° 1 (only for water/water units
if the condenser outlet probe is enabled)
>CDO2
>CDO2>CDO2
>CDO2
(If 2 condensers are present).
The submask displays the outlet temperature of condenser
n° 2 (only for water/water units if the condenser outlet probe is enabled)
> > 22.4
> > 22.4 > > 22.4
> > 22.4
temperature expressed in degrees centigrade
>EHt
>EHt>EHt
>EHt
(In water/air units, if the external air temperature probe is enabled).
Displays external
temperature
> > 15.6
> > 15.6 > > 15.6
> > 15.6
temperature expressed in degrees centigrade
>OPT
>OPT>OPT
>OPT
(In water-air units, if the operational temperature probe is enabled). Displays optio
nal
temperature
> > 18.8
> > 18.8 > > 18.8
> > 18.8
temperature expressed in degrees centigrade
MNT
MNTMNT
MNT
Service menu
>PROP
>PROP>PROP
>PROP
(Enable the "step adjustment" parameter first).
The submask is used to set step
adjustment.
> > P
> > P> > P
> > P
"P"=proportional adjustment, "P+I"=proportional + integral adjustment 55.01
>LL S
>LL S>LL S
>LL S
The submask is used to set the lower limit of the chiller setpoint with inlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade
55.04
55.05
>HL S
>HL S>HL S
>HL S
The submask is used to set the upper limit of the chiller setpoint with inlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade 55.06
>LL S
>LL S>LL S
>LL S
The submask is used to set the lower limit of the chiller setpoint with outlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade
55.07
>HL
>HL >HL
>HL S
SS
S
The submask is used to set the upper limit of the chiller setpoint with outlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade 55.08
>LL
>LL >LL
>LL U
UU
U
The submask is used to set the lower limit of the heat pump setpoint with inlet adjustment
>
> >
> > 0
> 0 > 0
> 0
expressed in degrees centigrade 55.09
>HL
>HL >HL
>HL U
UU
U
The submask is used to set the upper limit of the heat pump setpoint with inlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade 55.10
>LL
>LL >LL
>LL U
UU
U
The submask is used to set the lower limit of the heat pump setpoint with outlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade 55.11
>HL
>HL >HL
>HL U
UU
U
The submask is used to set the upper limit of the heat pump setpoint with outlet adjustment
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade 55.12
>OFFS
>OFFS>OFFS
>OFFS
(Only in the quick mind adjustment mode).
The submask is used to set the forced
shutdown temperature in the chiller mode
> > 4.5
> > 4.5 > > 4.5
> > 4.5
expressed in degrees centigrade
55.15
>OFF
>OFF>OFF
>OFFU
UU
U
(Only in the quick mind adjustment mode). The submask is us
ed to set the forced
shutdown temperature in the heat pump mode
> > 51.0
> > 51.0 > > 51.0
> > 51.0
expressed in degrees centigrade
55.16
>BAND
>BAND>BAND
>BAND
(Only visible in the step adjustment mode).
The submask is used to set the temperature
adjustment band