System information

C0240111-06-07-GB
50
Mask Description Para n°
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade
55.17
>SETV
>SETV>SETV
>SETV
The submask is used to enable setpoint variation
> > N
> > N> > N
> > N
"N"= disabled, "Y"= enabled
55.20
>SETT
>SETT>SETT
>SETT
The submask is used to set the setpoint variation signal type.
> > 4 20
> > 4 20 > > 4 20
> > 4 20
"4-20"= 4-20 mA
55.21
>SETL
>SETL>SETL
>SETL
The submask is used to set the minimum variation, corresponding to the minimum signal
> > 0
> > 0 > > 0
> > 0
expressed in degrees centigrade
55.22
>SETH
>SETH>SETH
>SETH
The submask is used to set the maximum variation, corresponding to the maximum signal
>
> >
> > 6.0
> 6.0> 6.0
> 6.0
expressed in degrees centigrade
55.23
>P PR
>P PR>P PR
>P PR
(if 2 pumps are present on the evaporator).
The submask is used to set the pump control
type.
> > AUTO
> > AUTO> > AUTO
> > AUTO
"AUTO"= automatic, "PMP1"= pump 1 only, "PMP2"= pump 2 only
55.28
>P ON
>P ON>P ON
>P ON
The submask is used to set the minimum pump operation time when the unit is switched on
> > 60
> > 60 > > 60
> > 60
time expressed in seconds
55.29
>P OF
>P OF>P OF
>P OF
The submask is used to set the minimum pump switch-
off time when the unit is switched
off
> > 60
> > 60 > > 60
> > 60
time expressed in seconds
55.30
>P
>P>P
>PUr
UrUr
UrL
LL
L
The submask is used to enable demand limit
> > N
> > N> > N
> > N
"N"=disabled, "Y"=enabled
55.31
> > 22.3
> > 22.3 > > 22.3
> > 22.3
temperature expressed in degrees centigrade
> > 50
> > 50 > > 50
> > 50
value expressed in percent
55.32
>P
>P>P
>PUrU
UrUUrU
UrU
(If the "demand limit" parameter is enabled").
The submask is used to set the power
limitation percentage in the heat pump mode
> > 0
> > 0 > > 0
> > 0
value expressed in percent
55.33
>DI O
>DI O>DI O
>DI O
The submask is used to set the digital input for switching on/off the unit
>
> >
> > N
> N> N
> N
"N"= disabled, "Y"= enabled
55.35
>DI S
>DI S>DI S
>DI S
(Only if the "operating mode" parameter is set on the heat pump).
The submask is used to
enable the digital input for the chiller/heat pump modes
> > N
> > N> > N
> > N
"N"= disabled, "Y"= enabled
55.36
>SALI
>SALI>SALI
>SALI
Evaporator antifreeze alarm setpoint
> > 04.0
> > 04.0 > > 04.0
> > 04.0
temperature expressed in degrees centigrade 35.29
>DALI
>DALI>DALI
>DALI
Evaporator antifreeze alarm differential
> > 04.0
> > 04.0 > > 04.0
> > 04.0
temperature expressed in degrees centigrade 35.30
>SR I
>SR I>SR I
>SR I
Evaporator antifreeze heating element setpoint
> > 04.0
> > 04.0> > 04.0
> > 04.0
temperature expressed in degrees centigrade 35.31
>DR I
>DR I>DR I
>DR I
Evaporator antifreeze heating element differential
> > 04.0
> > 04.0> > 04.0
> > 04.0
temperature expressed in degrees centigrade 35.32
>PASS
>PASS>PASS
>PASS
The submask is used to set the Service Password
> > 0
> > 0> > 0
> > 0
from 0 to 9999
USER
USERUSER
USER
User menu
>REG
>REG>REG
>REG
The submask is used to set the adjustment type.
> > STEP
> > STEP> > STEP
> > STEP
(Switch off the unit before changing this setting!!!). "STEP"= steps, "QM"= quick mind 39.01
>FLOU
>FLOU>FLOU
>FLOU
The submask is used to set the adjustment flow type.
> > IN
> > IN> > IN
> > IN
"IN"= inlet flow, "OUT"= outlet type 39.02
>BAND
>BAND>BAND
>BAND
The submask can be used to enable time bands
> > N
> > N> > N
> > N
"N"= disabled, "Y"= enabled 39.41
>SER
>SER>SER
>SER
The submask is used to enable the supervisor
> > N
> > N> > N
> > N
“N”= disabled, “SPV”= Supervision, “SQ”= Sequencer, “EDI”= Manager 3000 39.42
>PROT
>PROT>PROT
>PROT
(If the "supervisor" is enabled). The submask is used to set the communication protocol.
> > MODB
> > MODB> > MODB
> > MODB
"MODB"= modbus, "LON"= lonWorks, "STD"=standard Carel 39.45
>BAUD
>BAUD>BAUD
>BAUD
(If the "supervisor" is enabled).
The submask is used to set the speed of communication
expressed in bauds
> > 1200
> > 1200 > > 1200
> > 1200
Possible values: "1200"-"2400"-"9600"-"19,2"=19200 39.46
>ID
>ID>ID
>ID
(If the "supervisor" is enabled).
The submask is used to set the identification n° for
communicating in the supervisor network
> > 0
> > 0 > > 0
> > 0
address 39.47
>SV O
>SV O>SV O
>SV O
(If the "supervisor" is enabled). The submask is used to set on/off from the supervisor
> > N
> > N> > N
> > N
"N"= disabled, "Y"= enabled 39.43
>SV M
>SV M>SV M
>SV M
(If the "supervisor" is enabled).
The submask is used to enable the operating mode as
supervisor
> > N
> > N> > N
> > N
"N"= disabled, "Y"= enabled 39.44
>PASS
>PASS>PASS
>PASS
The submask is used to set the user Password
> > 0
> > 0 > > 0
> > 0
from 0 to 9999
CLH
CLHCLH
CLH
Clock menu, not available on this keypad
>NONE
>NONE>NONE
>NONE
I/O
I/OI/O
I/O
Input/output menu
>DI A
>DI A>DI A
>DI A
Displays digital input 1:4
> > CCCC
> > CCCC> > CCCC
> > CCCC
C=closed,A=open.
XXXX=[input1][input2][input3][input4]
>DI B
>DI B>DI B
>DI B
Displays digital input 5:8