Parts List

<NOTE>
 After changing Dip Switch settings, please re-power on the PIR Camera for it to operate with new Dip Switch Settings.


G
G
e
e
t
t
t
t
i
i
n
n
g
g
S
S
t
t
a
a
r
r
t
t
e
e
d
d
–
–
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
t
t
h
h
e
e
P
P
I
I
R
R
C
C
a
a
m
m
e
e
r
r
a
a
i
i
n
n
t
t
o
o
t
t
h
h
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
P
P
a
a
n
n
e
e
l
l
 Loosen the bottom fixing screw, and then insert a flat-head screwdriver to lift the back cover.
 Based on your needs, set Sensitivity Switch as shown in DIP Switch Position Table.
 Insert four AAL91 lithium batteries into the battery holder taking care to connect the polarity correctly.
 Put the Control Panel into learning mode, refer to Control Panel manual for details.
 Press and hold the Test button for 3 seconds to send a learn code, and then release the button when Red LED lights
up. The LED will be on for 20 seconds, indicating that the PIR Camera is in learning mode.
 If the Control Panel receives the signal from the PIR Camera, it will display the information accordingly. Within 20
seconds when the LED of the PIR Camera is on, select the PIR Camera on the Control Panel Webpage and click
“add” to include it into the Panel. Refer to the Control Panel manual for details.
 When the PIR Camera receives acknowledgement from the Control Panel, the LED of the PIR Camera will flash 6
times and then turn off to indicate successful learning.
 After the PIR Camera is learnt-in, put the Control Panel into Walk Test mode. Hold the PIR Camera in the desired
location, and press the Test button to confirm this location is within the signal range of the Control Panel.
 When you are satisfied that the PIR Camera works in the chosen location, you can proceed to installation.
<
<
N
N
O
O
T
T
E
E
>
>
 After the Test button is held and pressed for 3 seconds, the LED of the PIR Camera will be on for 20 seconds. If
the PIR Camera does not receive acknowledgement from the Control Panel within this 20-second period, the LED
will turn off. The Test button needs to be pressed and held for 3 seconds again to resend a learning code.
 If the PIR Camera already exists in a Control Panel system, you will need to first remove the PIR Camera from the
Control Panel before you can learn it into a different Control Panel.


Walk Test should be conducted to confirm proper operation and coverage of the PIR.


E
E
d
d
i
i
t
t
P
P
I
I
R
R
C
C
a
a
m
m
e
e
r
r
a
a
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
A
A
r
r
e
e
a
a
Follow instruction below to change PIR Camera Area in the Control Panel
1) Use the panel Edit Device function to change PIR Camera area setting.
2) Press and hold the Test button for 3 seconds on the PIR Camera to send a signal to the panel, and then release
the button when the LED lights up.


M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
&
&
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
M
M
e
e
t
t
h
h
o
o
d
d
 Mounting with mounting bracket:
The PIR Camera can be mounted on either a flat surface or in a corner situation with fixing screws and the mounting
bracket provided.
To mount 862EX-F1 with mounting bracket:
3) Use the mounting bracket as a template to drill holes on the wall for plugs. There are two mounting holes (A) for
surface fixing, and four mounting holes (B) for corner fixing (Picture1).
4) Push in the plugs and fix the mounting bracket on the wall with the screws (Picture2).
5) Mount 862EX-F1 with the hooks of the mounting bracket latched on the back cover of the 862EX-F1, and then
push downwards until you hear a click sound (Picture3).
<
<
N
N
O
O
T
T
E
E
>
>
 Please make sure the PIR Camera is properly hooked onto the mounting bracket, so that the internal tamper
switch will be fully compressed.
3