Parts List

ManualsBrandsClimax Technology ManualsCamera & PhotoPIR Motion Sensors Camera

Table Of Contents

Federal Communication Commission Interference Statement

PIR Motion Sensor Camera

VST-862

Introduction

VST-862 is a passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and captured images

(picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection.

The PIR Camera is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground. For

pet-immune models, a pet-immune range of 7 meters is provided, your household pets will not trigger false alarm within

this distance. For models that are compatible with repeaters/routers (P5 models only), the RF communication range can

be further extended into hard-to-reach areas.

The PIR Camera consists of a two-part design made up of a cover and a base. The cover contains all the electronics and

optics and the base provides a means of fixing. The base has knockouts to allow mounting on either a flat surface or in a

corner situation with a triangular bracket for corner mounting.

The VST-862 Series includes the following models:

Model Name

Flash LED

Infrared LED

Pet Immune

Compatible with

Repeater

VST-862-(P5)

P5 model only

VST-862-IL-(P5)

P5 model only

VST-862P-(P5)

P5 model only

VST-862P-IL-(P5)

P5 model only

Parts Identification

1. Flash LED / Infrared LED

The Flash LED (For 862(P)) or Infrared LED (For 862(P)-IL) delivers sufficient light

for image capture under low lighting condition.

2. Blue LED/Function Button

Blue LED:

(Please refer to LED Indicator description below for details)

Function Button Usage:

- Press and hold the button for 3 seconds to send a learn code, release when Blue

LED light on.

- Press the button once to enter test mode for 3 minutes.

- Press the button once to send a learn code to the repeater/router. (P5 models

only)

3. IR Sensor

4. PIR Camera Lens

5. Battery Compartment Cover

6. Tamper Switch

7. Battery Compartment

8. Sensitivity Adjustment Jumper Switch (JP3)

- Jumper On: the PIR’s sensitivity level is set to High.

- Jumper Off: the PIR’s sensitivity level is set to Normal. (Factory Default)

9. Sleep Timer Jumper Switch (JP2)

- Jumper On: After movement detection, the PIR Camera does not enter sleep mode

and will transmit detection signal again immediately if triggered (Factory Default).

- Jumper Off: PIR Camera has a “sleep time” of approximately 1 minute after motion

detection to conserve power.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

or “parked” on one pin.

Jumper On

The jumper link is inserted

connecting the two pins.

Jumper Off

if the jumper link is removed

or “parked” on one pin.

Summary of content (5 pages)

PAGE 1
PIR Motion Sensor Camera VST-862 Introduction VST-862 is a passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and captured images (picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection. The PIR Camera is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground. For pet-immune models, a pet-immune range of 7 meters is provided, your household pets will not trigger false alarm within this distance.
PAGE 2
Features  LED Indicator In Normal operation mode, the Blue LED will not light except in the following situations:  When the PIR Camera is in low battery condition, every time it transmits a detected movement, the Blue LED will flash for 2 seconds.  When the cover is opened and the tamper switch is violated, the Blue LED will flash for 2 seconds, to indicate it is transmitting “Tamper” signal.
PAGE 3
 Press and hold the function button for 3 seconds, release the button when the Blue LED light on, the Blue LED will light on for 25 seconds in learning mode, add PIR Camera into the Control Panel during this period (refer to your Control Panel to finish learn in process). If the PIR is successfully added into the Control Panel, the Blue LED will flash 6 times to indicate. If PIR is not added within 25 seconds, please repeat learning process.
PAGE 4
 Mounting the PIR Camera  Surface mounting: 1. Open the cover by loosening the Cover Screw using a Philips screwdriver. 2. Break through the 2 Surface knockouts at the center of base. 3. Use the holes as template to drill holes on the surface. 4. Insert the wall plugs if fixing it into plaster or brick. 5. Screw the base into the wall plugs. 6. Fit the cover onto the base and tighten.  Corner mounting: 1. 4 knockouts are made on the triangular bracket.
PAGE 5
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.