User's Manual
3
4. After joining the ZigBee network, if the Bellbox loses connection with current ZigBee network,
the LED 3 will flash every 20 minutes to indicate the situation. Please check your ZigBee
network condition and Bellbox signal transmission range to correct the problem.
z
z
F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you want to remove the Bellbox from current network and join a new network, you need to use
the Factory Reset function to clear the Bellbox for its stored setting and actively search for a
ZigBee network. To perform Factory Reset:
1. Press and hold the function button for 10 seconds, then release the button.
2. The Bellbox has been reset to factory default setting with all its previous network information
removed. It will now actively search for available ZigBee network again and join the network
automatically.
3. If the Bellbox successfully joins a ZigBee network, the LED3 will flash twice to indicate.
Installation
z
z
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
G
G
u
u
i
i
d
d
e
e
l
l
i
i
n
n
e
e
z The Bellbox is designed with a waterproof case to be mounted on external wall of you house.
z When mounting the Bellbox, mount as high as possible for its siren and strobe light to attract
attention when an alarm is activated.
z The Bellbox is designed to be mounted on a flat surface with fixing screws and plugs provided.
z The base has 4 mounting holes for you to screw the Bellbox onto the wall.
z
z
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
t
t
h
h
e
e
B
B
e
e
l
l
l
l
b
b
o
o
x
x
1. Use the 4 mounting holes as template, drill holes on the wall.
2. Insert the wall plugs if fixing it into plaster or brick.
3. Screw the base into the wall plugs. Make sure the tamper switch is properly depressed
against the wall surface.
4. Screw the cover back onto its base.
z
z
U
U
s
s
i
i
n
n
g
g
B
B
e
e
l
l
l
l
b
b
o
o
x
x
w
w
i
i
t
t
h
h
Z
Z
i
i
g
g
B
B
e
e
e
e
R
R
o
o
u
u
t
t
e
e
r
r
IMPORTANT NOTE
If the Bellbox installation location is away from your system control panel and requires ZigBee
routers to improve signal strength. DO NOT use a ZigBee Router without backup battery. A ZigBee
router without battery will be powered down during AC power failure and the Bellbox connected to
the router will lose connection with ZigBee network. You should plan your Bellbox installation
location using only ZigBee router with backup battery.
Appendix
(The Appendix information is for developers only.)
z
z
B
B
e
e
l
l
l
l
b
b
o
o
x
x
C
C
l
l
u
u
s
s
t
t
e
e
r
r
I
I
D
D
Device ID: IAS Warning Device: 0x0403
Endpoint: 0x01
Server Side Client Side
Mandatory
Basic (0x0000)
None
Identify(0x0003)
IAS Zone(0x0500)
IAS WD(0x0502)
Optional
None None
z
z
A
A
t
t
t
t
r
r
i
i
b
b
u
u
t
t
e
e
o
o
f
f
B
B
a
a
s
s
i
i
c
c
C
C
l
l
u
u
s
s
t
t
e
e
r
r
I
I
n
n
f
f
o
o
r
r
m
m
a
a
t
t
i
i
o
o
n
n
Identifier Name Type Range Access Default
Mandatory
/ Optional
0x0000
ZCLVersion
Unsigned
8-bit
integer
0x00 –0xff
Read
only
0x01 M
0x0001
ApplicationVersion Unsigned 0x00 – Read 0x00 O