User's Manual
3
2. Upon reset, the device will clear current ZigBee network setting and transmit signal to ZigBee
coordinator to remove itself from current ZigBee network. It will then actively search for
available ZigBee network again and join the network automatically.
Installation
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
G
G
u
u
i
i
d
d
e
e
l
l
i
i
n
n
e
e
It is recommended to install the Carbon Monoxide Detector in following locations.
Install the Carbon Monoxide Detector in your bedrooms to protect your safety.
For houses with garage, also mount near the internal door to garage and the room above the
garage for protection in case when car engin is not turned off.
Avoid mounting in following locations.
Inside kitchen and garage – to avoid false alarm when
Corner or location with stagnant air – to avoid false alarm
Fireplace – Keep at least 4.5 meters of distance to avoid false alarm.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
A mounting bracket is provide in the package for mounting the Carbon Monoxide Detector on the
wall.
1. Refer to Control Panel manual and put the Control Panel into Walk Test mode.
2.
Put the Carbon Monoxide Detector at desired installation location, press the Learn/Test button to
transmit signal to panel.
3.
If the panel receives signal, it will display the device signal strength. Check and make sure the
panel can receive signal normally from device at current location. If signal reception is
unsatisfactory, relocate the Carbon Monoxide Detector and repeat Step 1~3 until an ideal
installation location is found.
4.
Use the mounting bracket as template to mark the two holes on the wall at chosen location for
installing screws.
5.
Screw the mounting bracket onto the wall according to marked location. Install wall plugs if
necessary.
6.
Hook the Carbon Monoxide Detector onto the mounting bracket. Installation is now complete.
U
U
s
s
i
i
n
n
g
g
C
C
a
a
r
r
b
b
o
o
n
n
M
M
o
o
n
n
o
o
x
x
i
i
d
d
e
e
D
D
e
e
t
t
e
e
c
c
t
t
o
o
r
r
w
w
i
i
t
t
h
h
Z
Z
i
i
g
g
B
B
e
e
e
e
R
R
o
o
u
u
t
t
e
e
r
r
IMPORTANT NOTE
If the Carbon Monoxide Detector installation location is away from your system control panel and
requires ZigBee routers to improve signal strength. DO NOT use a ZigBee Router without backup
battery. A ZigBee router without battery will be powered down during AC power failure and the
Carbon Monoxide Detector connected to the router will lose connection with ZigBee network. You
should plan your Carbon Monoxide Detector installation location using only ZigBee router with
backup battery.
Appendix (For developers only.)
C
C
a
a
r
r
b
b
o
o
n
n
M
M
o
o
n
n
o
o
x
x
i
i
d
d
e
e
D
D
e
e
t
t
e
e
c
c
t
t
o
o
r
r
C
C
l
l
u
u
s
s
t
t
e
e
r
r
I
I
D
D
Device ID: IAS Zone 0x402
Endpoint: 0x01
Server Side Client Side
Mandatory
Basic (0x0000)
None
Identify(0x0003)
IAS Zone(0x0500)
Optional
None None
A
A
t
t
t
t
r
r
i
i
b
b
u
u
t
t
e
e
o
o
f
f
B
B
a
a
s
s
i
i
c
c
C
C
l
l
u
u
s
s
t
t
e
e
r
r
I
I
n
n
f
f
o
o
r
r
m
m
a
a
t
t
i
i
o
o
n
n
Identifier Name Type Range Access Default
Mandatory
/ Optional
0x0000
ZCLVersion
Unsigned
8-bit integer
0x00 –0xff Read only 0x01 M
0x0003
HWVersion
Unsigned
8-bit integer
0x00 –0xff Read only 0 O