User's Manual

5
5. Press and hold the RESET button on
CTC-1052RV for 20 seconds and release
button until you hear two beeps, followed
by a long beep.
<
<
N
N
O
O
T
T
E
E
>
>
) Meanwhile, WTRV/ WTRVS’s LED
turns from RED, then blink green to
steady green.
6. Start work test to check if WTRV/ WTRVS
is learnt in successfully.
7. Simply press the WTRV/ WTRVS button,
you will hear 6 contiunous beeps from
WTRV/ WTRVS.
8. During WTRV/ WTRVS’s beep, CTC-
1052RV will repond with 2 beeps
respectively. It indicates that WTRV/
WTRVS is within the operating range.
9. Press the Reset & Help button at the
same time to exit the learning mode. The
RED LED will dim to indicate that the
system is back to idle mode.
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
) It is prohibited to learn in another or
the same Pedant twice, unless the
previously learnt-in pendant is
removed first.
2.2. Learning Pendant #2
Refer to the following instructions to learn in
the second device (WTR- Series, Fall Sensor
or WTRV/ WTRVS).
For Normal Wrist Transmitters (WTR-) or
Fall Sensor
1. Press and hold the RESET button of
CTC1052RV for 6 seconds until you hear
the double beep
and followed by a long
beep.
2. The RED LED starts flashing. CTC-
1052RV is now in the learning mode.
3. Press and both the HELP and Pendant
#1 (WTR- Series or Fall Sensor) buttons
simultaneously until CTC-1052RV emits a
double-beep.
4. Pendant #2 has been learnt-in
successfully.
For Talking Pendant (WTRV/ WTRVS)
1. Press and hold the RESET button of
CTC1052RV for 6 seconds until you hear
the double beep and followed by a long
beep.
2. The RED LED starts flashing. CTC-
1052RV is now in the learning mode.
3. Press and hold the WTRV/ WTRVS
button for 5 seconds until you hear a long
beep. The WTRV/ WTRVS’s Green LED
turn to RED.
4. The WTRV/ WTRVS is now in the learn
mode.
5. Press and hold the HELP button on CTC-
1052RV for 20 seconds and release
button until you hear two beeps, followed
by a long beep.
<
<
N
N
O
O
T
T
E
E
>
>
) Meanwhile, WTRV/ WTRVS’s LED
turns from RED, then blink green to
steady green.
6. Start work test to check if WTRV/ WTRVS
is learnt into successfully.
7. Simply press the WTRV/ WTRVS button,
you will hear 6 contiunous beeps from
WTRV/ WTRVS.
8. During WTRV/ WTRVS’s beep, CTC-
1052RV will repond with 2 beeps
respectively. It indicates that WTRV/
WTRVS is within the operating range.
9. Press the Reset & Help button at the
same time to exit the learning mode. The
RED LED will dim to indicate that the
system is back to idle mode.
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
) It is prohibited to learn in another or
the same Pedant twice, unless the
previously learnt-in pendant is
removed first.
2.3. Remove Pendant #1 & #2
CTC-1052RV can be programmed to remove
Pendant #1 & #2 by Command 80, Command
81 or 82. Please refer to 3.2 Programming
Your 1052RV: Commands 80, 81 or 82 for
details.