Parts List



G
G
e
e
t
t
t
t
i
i
n
n
g
g
S
S
t
t
a
a
r
r
t
t
e
e
d
d
1. Orient and insert the battery according to polarity.
2. The Red Transmitter LED will begin to flash for 30 seconds to indicate the Motion Sensor is warming up. During the warming up
period, the Motion Sensor will not be activated. It is recommended that you stay away from the detection area during this time. After
the warming-up period, the Red will turn off and the Motion Sensor will enter normal operation.
3. Put the Control Panel into learning mode; refer to Control Panel manual for detail.
4. Press the Learn/Test Button to transmit signal to panel.
5. If the panel receives signal from Motion Sensor, it will display sensor info accordingly. Refer to your Control Panel to complete the
learn-in process.
6. After the Motion sensor is learnt-in, put the Control Panel into “Walk Test” mode, hold the sensor in the desired location, and press the
Test Switch to confirm this location is within signal range of the Control Panel.
7. When you are satisfied with the chosen location, you can proceed with
Installaiton.


M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
M
M
e
e
t
t
h
h
o
o
d
d
 The Motion sensor is designed to be mounted on either a flat surface or in a
corner situation with fixing screws and plugs provided.
 The base has knockouts, where the plastic is thinner, for mounting purpose. Two
knockouts are located on the back for surface fixing and four knockouts on the
sides for corner fixing.
 Surface mounting:
I. Detach the base and cover assembly.
II. Break through the knockouts on the inside of base
III. Using the holes as a template, drill holes in the surface.
IV. Insert the wall plugs if fixing it into plaster or brick.
V. Screw the base into the wall plugs.
VI. Fit the base onto the cover
 Corner mounting for IRM-23A:
I. Detach the base and cover assembly.
II. Break through the four corner knockouts.
III. Using the four holes as a template, drill holes in the surface of the
corner.
IV. Insert the wall plugs.
V. Screw the base into the wall plugs.
VI. Fit the base onto the cover
 Corner mounting for IRM-23B:
I. Break through the knockouts on the triangular bracket.
II. Using the two holes as a template, drill holes in the surface of the
corner.
III. Insert the wall plugs
IV. Screw the bracket into the wall plugs
V. Locate the Bracket Insertion Holes and fit the holes onto the Bracket
Insertion Hooks. Fitting the sensor onto the bracket should compress
the Tamper switch onto the Tamper Compression Protrusion on the
bracket.


I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
 Decide on the location of the Motion Sensor and if it is to be corner or surface mounted.
 After the installation site is selected, follow the steps described above to mount the Motion Sensor.
 Press the Test Switch to enter Test Mode. Walk around the protected area noting when the LED lights up and check that the
detection coverage is adequate.
 When detection coverage is found to be satisfying, installation is now completed.


I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
R
R
e
e
c
c
o
o
m
m
m
m
e
e
n
n
d
d
a
a
t
t
i
i
o
o
n
n
s
s
The Motion Sensor should be mounted at 1.9m~2.0m for optimal performance. It has a maximum range of 12 meters when sensor is
set to maximum range and mounted at 2 meters height. The pet immune models have a typical pet immune range of 7 meters.
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
3