User's Manual

Distance
Height
7M
1M
2M 3M
4M
5M
6M
2.3M
Pet Immune Area
z After the PIR is learnt-in, put the Control Panel into “Walk Test” mode, hold the PIR in the desired location, press
the Test button to confirm this location is within signal range of the Control Panel.
z When you are satisfied that the PIR work in the chosen location, you can proceed with installation.
z
z
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
M
M
e
e
t
t
h
h
o
o
d
d
z The PIR is designed to be mounted on either a flat surface or in a corner situation with fixing screws and plugs
provided.
z The base has knockouts, where the plastic is thinner, for mounting purpose. Four knockouts are for surface
fixing and four knockouts are for corner fixing as shown in the picture
z For corner mounting, at user’s own dicretion, an optional triangular bracket is provided to add Back Tamper
Protection. Mount the triangular bracket on he wall first with the two pointing sticks on top facing you. Then, you
can just fit the PIR onto the hooks of the triangular bracket or screw the PIR onto it.
z Surface mounting:
I. Remove the fixing screw and cover assembly.
II. Break through the appropriate knockouts on the base.
III. Using the holes as a template, drill holes in the surface.
IV. Insert the wall plugs if fixing it into plaster or brick.
V. Screw the base into the wall plugs.
VI. Screw the cover back onto its base.
z Corner mounting:
I. Break through the two knockouts on the triangular bracket.
II. Using the two holes as a template, drill holes in the surface of the corner
III. Insert the wall plugs
IV. Screw the triangular bracket into the wall plugs with the two pointing sticks on top facing you.
V. Fit the PIR onto the hooks of the triangular bracket
VI. If necessary, open the PIR by removing the fixing screw and cover assembly
VII. Break through the appropriate corner fixing knockouts.
VIII. Using the corner fixing knockouts as a template, drill holes in the surface in the corner again
IX. Insert the wall plugs if fixing it into plaster or brick.
X. Screw the base into the wall plugs
XI. Screw the cover back onto its base
z
z
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
z Decide on the location of the PIR and if it is to be corner or surface mounted.
z After the installation site is selected, follow the steps described above to mount the PIR.
z Press the Test Button to enter Test Mode. Walk around the protected area noting when the LED lights up and
check that the detection coverage is adequate.
z When detection coverage is found to be satisfying, installation is now completed.
z
z
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
R
R
e
e
c
c
o
o
m
m
m
m
e
e
n
n
d
d
a
a
t
t
i
i
o
o
n
n
s
s
The PIR is designed to give a typical detection range of 12 meters when
mounted at 2 meters above ground. When mounted at 2.3 meters above
ground, it gives a typical PET IMMUNE range of 7 meters. As the PIR is
higher from above ground, it gives a farther PET IMMUNE range. To take
full advantage of IRP-9, the following guidelines should be considered:
z It is recommended to install the PIR in the following locations
z Mount the detector at 2.1 M ~ 2.4 M high for best performance:
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
) For the most desired performance of IRP-9, remember to adjust the height of IRP-9 mounting site
respectively to the height of the tallest animal in the house. As the taller than average dogs require the
IRP-9 to be mounted higher for the Pet Immunity purpose.
) When deciding on the height of the IRP-9 mounting site, remember to take the possible blind spot into
consideration. The blind spot underneath the IRP-9 enlarges proportionally to the height of the IRP-9
mounting site.
z Mount where the animals cannot come to the detection area by climbing on furniture or other objects.
z Don’t aim the detector at stairways the animals can climb on.
z In a position such that an intruder would normally move across the PIR’s field of view.
z In a corner to give the widest view.
z Where its field of view will not be obstructed e.g. by curtains, ornaments etc.
z Limitations
z Do not position a PIR to look directly at a door protected by a Door Contact, this could cause the Door
Contact and PIR radio signals to be transmitted at the same instant when entering, canceling each other out.
z Do not install the PIR completely exposed to direct sunlight.
z Avoid installing the PIR in areas where devices may cause rapid change of temperature in the detection
area, i.e. air conditioner, heaters, etc.
z Avoid large obstacles in the detection area.
z Not pointing directly at sources of heat e.g. fires or boilers, and not above radiators.
z Avoid moving objects in the detection area i.e. curtain, wall hanging etc.
FCC Caution :To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or
peripheral devices).