User's Manual

z When the Function Button is pressed under tamper condition, test mode, or if PIR is under low battery condition.
z
z
B
B
a
a
t
t
t
t
e
e
r
r
y
y
z The PIR uses one 3V Lithium battery as its power source. A low battery signal will be sent to the Control Panel
along with regular signal transmissions for the Control Panel to display the status accordingly.
z The PIR will report its battery percentage to the Control Panel respectively at 100%, 75%, 50%, 25%. If the battery
voltage is low (25%), a Low Battery signal will be sent to the Control Panel to notify the user.
z The battery is pre-inserted by the factory before shipment with a battery insulator inserted.
<
<
N
N
O
O
T
T
E
E
>
>
) When changing battery, after removing the old battery, press the Tamper Switch twice to fully
discharge before inserting new battery.
z
z
A
A
d
d
d
d
i
i
n
n
g
g
D
D
e
e
v
v
i
i
c
c
e
e
(
(
I
I
n
n
c
c
l
l
u
u
s
s
i
i
o
o
n
n
)
)
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other
manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless
of vendor to increase reliability of the network.
z Pull out the battery Insulator steadily.
z The LED indicator will flash for 30 seconds (The PIR is warming up). During the warm up period, the PIR will not be
activated. It is recommended that you stay away from the detection area during this time. After the warming period is
over, the LED will turn off and the PIR will be ready for operation.
z Put the Z-wave control panel into Inclusion mode (please refer to the Z-wave control panel manual).
z Within 1.5 seconds, press the Function Button 3 times.
z Refer to the operation manual of the Z-wave gateway or control panel to complete the adding process.
z Please press and release the Tamper Switch once after inclusion is completed to ensure the Gateway/Control Panel
recognizes the current Tamper condition.
z If the device has already been added (included) into another Z-wave Gateway/Control Panel, or if the device is
unable to be added into the current Z-wave Gateway/Control Panel, try removing it first (see Removing Device).
z
z
R
R
e
e
m
m
o
o
v
v
i
i
n
n
g
g
D
D
e
e
v
v
i
i
c
c
e
e
(
(
E
E
x
x
c
c
l
l
u
u
s
s
i
i
o
o
n
n
)
)
The device must be removed from existing Z-wave network before being added into another.
Exclusion Mode
z Put the Z-wave gateway or control panel into Exclusion mode (please refer to the Z-wave or control panel manual).
z Within 1.5 seconds, press the Function Button 3 times and the device will be removed from the Z-wave network.
Factory Reset
Factory resetting the device will restore it to factory default settings (i.e. not included into any Z-wave network). Please only
use this procedure if the Z-Wave gateway or control panel is lost or otherwise inoperable.
z Press and hold the Function Button of the device for 12 seconds to factory reset.
z
z
R
R
a
a
n
n
g
g
e
e
T
T
e
e
s
s
t
t
To test whether the device is able to communicate with the Z-wave gateway or control panel:
z Put the gateway / panel into range test mode (Walk Test).
z Press the Function Button on the device
z The gateway / panel should display if the device is within the operation range (please refer to the operation manual
of the gateway / panel).
z
z
Z
Z
-
-
w
w
a
a
v
v
e
e
S
S
l
l
e
e
e
e
p
p
M
M
o
o
d
d
e
e
z The PIR will enter Z-wave Sleep mode (to conserve power) after waking up for a short period of time (~10 seconds).
While in Z-wave sleep mode, Z-wave gateways or control panels are unable to send commands to the PIR.
z To program the PIR using the Z-wave Gateway/Control Panel, please send command(s) to the PIR within the
wake-up period.
z
z
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
M
M
e
e
t
t
h
h
o
o
d
d
z The PIR is designed to be mounted on either a flat surface or in a corner situation
with fixing screws and plugs provided.
z The base has knockouts, where the plastic is thinner, for mounting purpose. Four
knockouts are for surface fixing.
z For corner mounting, an optional triangular bracket is provided to add Back Tamper
Protection. Mount the triangular bracket on the wall first with the two pointing sticks
on top facing you. Fit the PIR onto the hooks of the triangular bracket or screw the
PIR onto it.
z Surface mounting:
I. Remove the fixing screw and cover assembly.
II. Break through the appropriate knockouts on the base.
III. Using the holes as a template, drill holes in the surface.
IV. Insert the wall plugs if fixing it into plaster or brick.
V. Screw the base into the wall plugs.