Parts List

ManualsBrandsClimax Technology ManualsElectronicsRemote Keypad

REMOTE KEYPAD (KP-39B-F1)

 Parts Identification

1. Arm Key

2. Home Key

3. Disarm Key

4. Panic Alarm (if enabled)

- press both 1 and 3 to trigger Panic Alarm

5. Fire Alarm (if enabled)

- press both 4 and 6 to trigger Fire Alarm

6. Medical Alarm (if enabled)

- press both 7 and 9 to trigger Medical alarm

7. Send Learning Code

- press ＊then 7 Key

(under Test Mode)

- press both # and  keys

(under Normal Operation Mode)

8. # Key

9.  Key

10. Fault LED (Orange LED)

11. Power LED (Green LED)

12. Mounting Holes

13. Tamper Switch

<NOTE>

 A short beep will sound along with key pressing to indicate that the button pressed is valid.

 4 continuous beeps will sound indicating mistake and the user should repeat the process again.

 LED Indicator

 Power LED (Green):

 On for 5 seconds: after successful completion of a valid keystroke sequence.

 Flash for 5 seconds: low battery in Normal Operation Mode.

 If the Power LED turns off before a valid keystroke sequence is completed, the previous entered keys are

ignored.

 Fault LED (Orange):

 Disarm Key and Orange LED On along with 5 beeps: Alarm Memory (depend on Control Panel).

 Flash:

 Flash only: No response sent by the control panel within 9 seconds.

Summary of content (5 pages)

PAGE 1
REMOTE KEYPAD (KP-39B-F1)  Parts Identification 1. Arm Key 2. Home Key 3. Disarm Key 4. Panic Alarm (if enabled) - press both 1 and 3 to trigger Panic Alarm 5. Fire Alarm (if enabled) - press both 4 and 6 to trigger Fire Alarm 6. Medical Alarm (if enabled) - press both 7 and 9 to trigger Medical alarm 7. Send Learning Code - press ＊then 7 Key (under Test Mode) - press both # and  keys (under Normal Operation Mode) 8. # Key 9.  Key 10. Fault LED (Orange LED) 11. Power LED (Green LED) 12.
PAGE 2
    General Operation          When idle, Remote keypad is in Stand-by mode and uses no power. It will activate and wake-up for 5 seconds when any key is pressed. After 5 seconds of key inactivity, the power goes off and it returns to Stand-by mode. Tamper Protection    Remote keypad uses one CR123 3V Lithium battery as its power source. Remote keypad can also detect the battery status. If the battery voltage is low, the Power LED will flash for 5 seconds during operation.
PAGE 3
received. If remote keypad does not perform 3 beeps, please restart the learning procdeure. After the Remote keypad is learnt-in, put the Control Panel into Walk Test mode, hold the Remote keypad in the desired location, and send the learning code to the Control Panel to confirm this location is within the signal range of the Control Panel. To send the learning code, either press the ＊ key then 7 key under Test Mode or press both # and ＊ keys together under Normal Operation Mode.
PAGE 4
 Factory Reset Resetting the Keypad to factory default will restore Keypad’s own PIN Code to 0000 and clear all panel learning memory. Reset to factory default: Step 1 Remove the batteries and release the tamper. Step 2 If “Arm/Home with Control Panel PIN Code” method is selected, press & hold 3 key while inserting the battery .back. .If “Arm/Home without Control Panel PIN Code” method is selected, press & hold 4 key while inserting the battery .back.
PAGE 5
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.