User's Manual

2
ZigBee is a wireless communication protocol that is reliable, has low power consumption and has high
transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to
be included in a network and are coordinated for data exchange and signal transmission.
z
z
J
J
o
o
i
i
n
n
i
i
n
n
g
g
t
t
h
h
e
e
Z
Z
i
i
g
g
B
B
e
e
e
e
N
N
e
e
t
t
w
w
o
o
r
r
k
k
As a ZigBee device, the Power Switch needs to join a ZigBee network to receive commands and transmit
energy consumption information. Follow the steps bellow to join the Power Switch into a ZigBee network.
1. Plug in the Power Switch into a power outlet.
2. Press and hold the function button for 10 seconds as the Power Switch resets and starts searching for
existing ZigBee network. Please make sure the permit-to-join feature on the router or coordinator of your
ZigBee network is enabled.
3. If the Power Switch successfully joins a ZigBee network, the LED Indicator will flash twice to confirm.
4. After joining the ZigBee network, the Power Switch will be registered in the network automatically. Please
check the Zigbee network coordinator, system control panel or CIE (Control and Indicating Equipment) to
confirm if joining and registration is successful.
5. If registration and joining to the network is unsuccessful, please check your ZigBee network coordinator,
system control panel or CIE setting to ensure the permit-to-join function is available, and then use the
Factory Reset function below to join the ZigBee network.
z
z
B
B
i
i
n
n
d
d
i
i
n
n
g
g
w
w
i
i
t
t
h
h
C
C
o
o
n
n
t
t
r
r
o
o
l
l
l
l
e
e
r
r
After joining the ZigBee network, the Power Switch can bind itself with a controller device which can be used
to turn on/off the Power Switch. To bind the Power Switch and the device:
1. Press and hold the Function Button for 3 seconds, then release the button. The Power Switch will send
binding request to the coordinator.
2. Refer to your controller manual to send binding request for the device within 16 seconds.
3. If binding is successful, the Power Switch LED indicator will flash 5 times to confirm. You can now use the
controller to adjust power output level for the Power Switch.
4. If binding is unsuccessful, please retry the binding process.
z
z
F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you want to remove the Power Switch from current network and join a new network, you need to use the
Factory Reset function to clear the Power Switch from its stored setting and information first before it can join
another network. To perform Factory Reset:
1. Press and hold the switch button for 10 seconds, release the button until the LED Indicator flash once.
2. The Power Switch has been reset to factory default setting with all its previous network information
removed. It will now actively search for available ZigBee network again and join the network automatically.
3. If the Power Switch successfully joins a ZigBee network, the LED Indicator will flash twice to indicate.
z
z
Z
Z
i
i
g
g
B
B
e
e
e
e
R
R
o
o
u
u
t
t
e
e
r
r
D
D
e
e
v
v
i
i
c
c
e
e
C
C
a
a
p
p
a
a
c
c
i
i
t
t
y
y
(
(
P
P
S
S
S
S
-
-
2
2
9
9
Z
Z
B
B
S
S
R
R
/
/
P
P
S
S
M
M
-
-
2
2
9
9
Z
Z
B
B
S
S
R
R
O
O
n
n
l
l
y
y
)
)
The Power Switch models with Router function allow other ZigBee devices to join the ZigBee Network
through the Router. The Power Switch Router has maximum capacity of 40 devices/routers; the Power
Switch Meter Router has maximum capacity of 10/routers.
Model No.
Maximum ZigBee Device
+ Router Capacity
PSS-29ZBSR 40
PSM-29ZBSR 10
Operation
z
z
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
z Plug the Power Switch into a power outlet.
z Plug the appliance into the socket of the Power Switch. The appliance must be in ON status.
z IMPORTANT NOTE: The Power Switch does not have a backup battery and will be powered down
when AC power fails. DO NOT use the Power Switch as router for your security sensor or alarm control
devices such as Door Contact, PIR Sensor…etc., otherwise the sensors will lose connection to ZigBee
network if the Power Switch is disconnected from AC power. Plan the installation locations of these
security sensors without using the Power Switch and only use a router with backup battery for them.
The router function of the Power Switch should ONLY be used to provide signal range extension for
other Power Switches/Dimmer.
z
z
A
A
p
p
p
p
l
l
i
i
a
a
n
n
c
c
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
z After the Power Switch has successfully joined a ZigBee network, the coordinator can remotely turn
on/off the Power Switch to control the appliance