Installation Instructions

ManualsBrandsClimax Technology ManualsElectronicsWireless Indoor Siren

Wireless Indoor Siren (SR-32 / SR-32-F1)

The Indoor Siren is used to attract attention when alarm signal is received from Control Panel by activating its siren. The Siren can also alert you to

tamper violation, and low battery status.

Identifying the Parts

1. Tamper Switch

The Tamper switch will be activated when the Siren is removed from mounted

surface, or when its cover opened.

2. Battery Compartment

The Siren is powered by two 1.5V D-Cell alkaline batteries.

Battery Switch

The battery switch is used when battery is installed in the Indoor Siren. To power on/off the

Indoor Siren, switch the ON/OFF switch.

4. Mounting Holes x 3

5. Learn Button

Accessories included

In addition to the Siren itself, the following accessories are also included in the package:

a. 3 x large wall plugs.

b. 3 x fixing screws for wall mounting

c. 2 x 1.5V D alkaline batteries (pre-inserted)

Battery and Low Battery Detection

The Siren is powered by two 1.5V Alkaline D batteries, it features low battery detection and will transmit

low battery signal when low battery voltage is detected.

When changing batteries, after removing the old batteries, press the Tamper Switch a couple times to

fully discharge before inserting new batteries.

<NOTE>

 Only use specified batteries with the device. When replacing batteries, always replace the

whole set, do not mix different types of batteries or new and used ones to avoid damaging the device.

Supervision

The Siren will transmit a supervisory signal every 30-50 minutes in normal operation mode. If this signal is not received, the Control Panel will

indicate that the particular Siren is experiencing an out-of-order problem.

Siren Function Overview



Audio & Visual Status Indication

While arming / disarming the system, the SR-32 uses different methods to distinguish various statuses for the user, as listed in the table.

* The Siren Audio indication will be affected by the Confirmation ON / OFF setting. When setting Confirmation to OFF, the confirmation sound

will not be available. Refer to Control Panel Siren setting for Confirmation function.



Alarm Memory

If an alarm was triggered in your absence and the system was not disarmed before alarm length expiry, the Siren will sound a short alarm

when the system is disarmed or home armed to warn the user that an alarm has been triggered when he is away. This suggests that the

intruder could still be within the premises.



Alarm Length

When an alarm is activated by Control Panel, the Control Panel will notify the Siren to start alarming according to the panel’s own alarm length

setting. When the Panel’s alarm length expires, it will notify the Siren to stop alarm.

If the Siren does not receive the Control Panel’s signal to stop alarm, it will sound alarm for a maximum of 15 minutes, then stop the alarm.

Siren Audio

Arm/Home 1 beep*

Disarm 2 beeps*

Arm (Low Battery) 3 beeps

Disarm (Low Battery) 3 beeps

Arm (Tamper) 5 beeps

Disarm (Tamper) 5 beeps

Entry/Exit Sound Count-down beeps

Summary of content (5 pages)

PAGE 1
Wireless Indoor Siren (SR-32 / SR-32-F1) The Indoor Siren is used to attract attention when alarm signal is received from Control Panel by activating its siren. The Siren can also alert you to tamper violation, and low battery status. Identifying the Parts 1. Tamper Switch The Tamper switch will be activated when the Siren is removed from mounted surface, or when its cover opened. 2. Battery Compartment The Siren is powered by two 1.5V D-Cell alkaline batteries. 3.
PAGE 2
For example:   If the Panel alarm length is set more than 15 minutes, after an alarm is activated, instead of waiting panel alarm length to expire, the Siren will stop alarming after 15 minutes.  If the panel is under disarm mode and the Siren` tamper switch is triggered, the Siren will activate alarm for 15 minutes since the panel is under disarm mode and will not activate alarm from tamper trigger.
PAGE 3
     Exit beeps of home arm: set exit countdown beep volume under Home Arm Mode. Entry beeps of full arm: set entry countdown beep volume under Full Arm Mode. Entry beeps of home arm: set entry countdown beep volume under Home Arm Mode. Door Chime: set the volume of the Door Chime sound (Ding-Dong Sound). Behavior          Burglar trigger in home arm: Enable or Disable whether Siren is activated when an alarm is triggered under Home Arm.
PAGE 4
Figure 2 Step 11. Enable Siren Tamper function on the Control Panel (Please refer to the Control Panel instruction manual) Step 12. Check if the installation is successful by testing from the Control Panel by arming and disarming function. Successful arming/disarming is indicated by the table provided in Audio & Visual Status Indication.  If 5 short-beeps are noticed while arming/disarming, it means the tamper is not fully depressed.
PAGE 5
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.