Bluetooth Mono Headset HCM-100 User manual
All rights reserved For the best performance and prevention of any damage to, or misuse of the HCM-100, please read the entire information prior to using the HCM-100. Any modifications or changes to this manual due to typographical errors or inaccuracies of stated information shall only be made by Clipcomm Inc.
Table of Content Introduction ------------------------------------------------------------------------------------------------------Part description--------------------------------------------------------------------------------------------------Using the headset----------------------------------------------------------------------------------------------1. Wearing--------------------------------------------------------------------------------------------2.
Introduction The Clipcomm Bluetooth headset HCM-100 is a light weight wireless headset utilizing Bluetooth technology. This product can be used as an audio accessory for devices supporting either the Bluetooth Headset or Handsfree Profiles. Included in package [Included in package] Make sure if below items are fully included in the package prior to use and contact the seller if any item is excluded.
Part description Ear loop Charging port Status LED Multifunction Button Volume Controls MIC Using the headset [Wearing a headset] You can wear the headset with the adjustable ear loop that can be worn on the left or right ear as below. Left Right [Charging] - Remove the cover on the charging port as below and connect the charger.
When the charger is connected properly, the LED indicator will show a solid red light. (With power on, the headset will turn off while connected to the charger.) z The button stops working while the device is charging. z 2 hours of charging time is estimated to charge the headset fully. z When charging is completed, the LED indicator will turn off. !note: Do not use other chargers except the approved charger. Using other brand charger will cause a malfunction or damage of the device.
z z z When paring is successful, short and high-pitched tone will sound and the blue light on LED will flash 5 times. To connect the headset to another type of device (a PDA, for example), the device must support Headset or Handsfree Profiles. Refer to the user manual of the other device to set up the headset and follow above instruction again. If the HCM-100 is in "Pairing Mode" over 3 minutes without being paired to any device, the headset will turn off automatically.
Briefly press the multifunction button. Additional function during a call [Transferring calls*] Briefly press the multifunction button to transfer a call from a mobile phone to a headset while talking over the phone, (The headset and mobile phone must be paired prior to this process). To transfer a call from a headset to a mobile phone, press and hold VOLUME UP button [▲] for 5 seconds.
LED indication Function Power on Power off Paring The headset and mobile phone is connected and the user is talking on the headset Unintentional link loss (Until the lost link is recovered) Charging Charging completed Beep The HCM-100 once The HCM-100 once The HCM-100 twice The HCM-100 once beeps Status of LED The blue LED light flickers 5 times quickly. beeps The blue LED light flickers 5 times quickly beeps The red and blue LED light flicker in turn continuously.
Do not modify, repair, or take apart Do not expose directly to water, alcohol, benzene, etc for cleaning Do not expose directly to flammables Do not place or keep the unit near flammables Keep unit away from humidity & dust 10
Do not place the heavy object on the units Caution z z z Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. There is a risk of explosion if the battery is replaced with incorrect type. The ear loop is made of a durable plastic that does not break but bend. However, repetition of bending is not recommended.
Standard and Specification Title Bluetooth Spec Supported profiles Frequency Transmitting output Cover range Standby time Talking time Charging time Durable temperature Adapter rated voltage Size and weight Wireless Data communication device for system(HCM-100) 2.0 SIG Headset or Handsfree Profiles. 2.402~2.480Ghz(ISM band) Class 2 Within 10m/33ft Up to 170 hours Up to 5 hours Approximately 2 hours -20 C ~ 60C AC 100 ~ 220V, 50~ 60HZ 41 × 18.8 × 16.
Regulatory Information FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received. Including interference that may cause undesired operation. FCC WARNING: This equipment may generate or use radio frequency energy.
