OWNERS MANUAL 7” Table Top Tile Saw MODEL:CTC701 FORM <
WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer.
Table Of Contents CONTENTS I. CTC701 Safety Instructions PAGE 4-9 1. Basic Safety Instructions 1.1 Symbols 1.2 Safety Precautions 1.3 Dust and Silica Warning 1.4 Safety instructions for working with the machine 10-12 2. Machine Description 2.2 Use of Machine 2.3 Layout 2.3 Technical Specifications 2.4 Items Includes With The CTC701 10 10-11 12 12 12-14 3. Assembly 3.1 3.2 3.3 3.4 3.5 3.
I. CTC701 Safety Instructions 1. Basic Safety Instructions The CTC701 is exclusively designed for the cutting of ceramic tiles, porcelain tiles, natural stone flooring materials, artificial stone flooring materials, and terracotta materials up to 2-1/4” (57mm). Uses other than the manufacturer's instructions will violate the machine’s warranty. The Saint-Gobain Abrasives, Inc. shall not be held responsible for any resulting damage. Any risk shall be borne entirely by the user.
1.2 Safety Precautions Important! The following safety precautions must always be observed. Additional Warning/Hazard Symbols Keep all guards in place when operating any piece of equipment Keep hands, feet, hair, and clothing away from all rotating parts Never tamper with the governor components of settings to increase the maximum speed. Severe personal injury and damage to the engine or equipment can result if operated at speed above maximum. Always obey the maximum speed rating of the blade.
1.3 Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm.
1.4 Safety instructions for working with the machine Before Commencing Work: • Know your CTC701 Tile Cutting machine! Read the Operator’s manual carefully. Learn the operation, application and limitations, as well as the specific potential hazards peculiar to this equipment and its usage. • Before commencing work, make yourself familiar with the working environment at the place of use.
• • • • • • • • • • Use only three-wire grounded extension cords suitable for use outdoors and of sufficient gage to accommodate power requirements. Ground the machine! The tile saw must be grounded while in use to protect the operator from electric shock. The motor is equipped with a three prong grounding type plug to fit the proper type receptacle. The green [or green & yellow] conductor in the cord is grounding wire. NEVER connect the ground green [or green & yellow] wire to a live terminal.
1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. 3. The blade must be properly fitted over the arbor with the relief side of the collars facing the blade. 4. The blade shaft nut must be tightened securely against the outside blade shaft collar. 5.
2. Machine Description Any modification, which could lead to a change in the original characteristics of the machine, may be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in conformity with the safety regulations. The CTC701 Tile saw is designed for durability and high performance for onsite wet and dry cutting operations of a wide range of tiles.
Electrical Motor and Switch (3) Motor with 1.07 HP (800W). The motor is designed to operate on 115-120 volts, 60 Hz, single phase electrical circuits. Use a circuit with a 15 Amp circuit breaker for best performance. The ON-OFF switch also serves as emergency stop. Tilting Table (4) The cutting table tilts to 45 ° for making miter cuts. To tilt the cutting table loosen the two screws on the side and pivoting the table. The CTC701 has a built in gauge for precise angle adjustments.
2.
3.1 Tool Assembly Only use NORTON CLIPPER continuous rim blades with a maximum diameter of 7” (177mm) can be used with the CTC701. All tools used must be selected with regard to their maximum permitted cutting speed for the machine’s maximum permitted rotation speed. Before mounting a new blade into the machine, switch off the machine and isolate it from the main source of electricity. Plate Blade Cover 3.
• • • • Fill the water pan with clean water up to 3/16” (5mm) from the upper edge of the water tray. Ensure that water is delivered adequately to both sides of the blade, as insufficient water supply may result in premature failure of the diamond blade and is not covered by any warranty. Always make sure that there is enough water in the pan and refill if necessary. In case of frost, empty the water cooling system from its water. 4. Transport And Storing 4.
the table to align the guide. Then tighten it back. 5.3 General Advice For Cutting • • • • • • Only tiles with max. dimensions of 15-3/4”x15-3/4”x1/4” (400x400x6mm) and max. weight of 6-1/2 lbs (3kg) can be cut with the machine. Before beginning work make sure tools are firmly seated! Select the right Norton Diamond Blade as recommended by Norton Clipper which depends on the material to be cut, and if cutting wet or dry. Make sure the water tray contains enough water.
6.3 Cleaning of the machine Your machine will last longer if you clean it thoroughly after each day of work, especially water pan, motor and blade flange. To clean disconnect the machine from the power source and wipe down the CTC701 with a damp cloth. 7. Trouble Shooting 7.1 Trouble Shooting Procedures Should any fault occur during the use of the machine, turn it off, and isolate it from the electrical supply.
8. Parts List Section Ordering Information 1. List model number and serial number of machine. 2. List part number and serial number of part not the item number. 3. Wherever alternate parts are shown due to product improvement, inspect the part you have and provide additional description as necessary. 4. Specify mode of shipping desired, such as, parcel post, truck, U.P.S., best way, etc. Clear instructions will avoid problems and faulty deliveries. If not sure, please send us the defective part.
8.
8.
POS 49 50 51 52 53 54 Part# 243046 243047 243048 243049 243050 243051 55 56 57 58 59 60 243052 243053 243054 243055 243056 -NA- 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 243057 243058 243059 243060 243061 243062 243063 243064 235104 243065 243066 243067 243068 235103A 243069 243070 235065 502088 243071 243072 243073 243074 224237 27539 243075 243076 243077 243078 243079 243080 UPC# 00310340199 00310340200 Call for assistance 00310361134 70184600873
NOTES: 21
Saint-Gobain Abrasives 2770 West Washington Stephenville, TX 76401 Phone: 800-554-8003 Fax: 800-443-1092 22
