OWNERS MANUAL Handheld Drill MODEL: HHD323 FORM <
WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer.
Table Of Contents CONTENTS I. Preparation A. Safety Precautions B. Assembly C. Specifications D. Electrical Supply F. Generator G. Grounding Instructions H. Electrical Connections PAGE 4-6 7 7 8-10 8 8 8-10 II. Operation A. Core Bit Installation B. Water Supply C. Drilling Operation D. Hand Held Drilling Technique 10-11 11 11-12 12-13 III. Component Description A. Diagram 14 IV. Parts List Section A. Ordering Information B. HHD323 Exploded View Parts Drawing C.
I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well-ventilated, unoccupied approved areas, and away from sparks or flames. Do not fill the fuel tank while the engine is hot or running. Do not start the engine near spilled fuel. Never use the fuel as a cleaning agent.
Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm.
1. Know your drilling machine! Read the Owner’s manual carefully. Learn the operation, application and limitations, as well as the specific potential hazards peculiar to this equipment. 2. NEVER connect the green [or green & yellow] wire to a live terminal. 3. Use only three-wire grounded extension cords suitable for use outdoors and of sufficient gage to accommodate power requirements. 4. Replace frayed or damaged extension cords. 5. Keep the work area clean avoiding cluttered work areas. 6.
I. PREPARATION B. Assembly The HHD323 handheld drill is shipped completely assembled except for core bit adapters, core bit, and the collar handle. Inspect the drill for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. Saint-Gobain Abrasives, Inc. is not responsible for any freightrelated damages. Be sure you have the following items: 1. HHD323 handheld drill 2. 27mm Wrench 3. 12” Adjustable wrench 4. 5mm Allen wrench 5. Adapter M18 female to 5/8” male 6.
D. Electrical Supply The HHD323 handheld drill is furnished with a 115 volt, single phase motor. This motor operates within a power range of 110 to 120 volts. Serious damage can result if the supply line voltage does not fall within this range. The following wire sizes are recommended when using an extension cord: Wire Gauge (AWG) Number 14 Number 12 Number 10 Number 08 Length Of Wire 25 Feet 50 Feet 75 Feet 100 Feet For Best performance use 50 feet of 10 gauge extension cord.
The installation of cables, plugs, and switches must be made ONLY by an authorized electrician. All installations must be made according to the local regulations for electrical equipment. All components must meet local requirements. For additional information see the National Electrical Code (NEC) for the United States and Canadian Electrical Code for Canada. The use of a 3-prong adapter is prohibited in Canada by the Canadian Electrical Code. Fig.
• For Additional Safety Use A Ground Fault-Interrupter (GFCI ) Device.
2. Placing one wrench on the machined flats of the output shaft and one wrench on the end adapter of the core bit tighten the bit on the spindle. Note: Attempting to turn the bit by the barrel rather than by the adapter nut may break the weld between the adapter nut plate and the barrel. When using any Hand Held Drill never hand drill a bit larger than 4” (100 mm) in diameter. Only use a Drill Stand for drill bits larger than 4” (100 mm) in diameter. B. Water Supply: 1. 2. 3. 4. 5.
3. Slowly guide the bit into the hole so that there is no skidding or movement of the drill. The entire circumference of the core bit should penetrate the drilling surface before additional pressure is applied to the handle. 4. Exert steady pressure while drilling. NEVER force the bit into the material! 5. Do not stop the flow of water or rotation of the bit while the core bit is drilling. 6. Check the core bit if the drilling rate decreases noticeably.
1. Start The Drill At 45° To The Work Surface With The Bit About 1/2” From The Work Surface. The Drill Must Be Running At Full Speed Before The Bit Comes In Contact With The Work Piece 2. Slowly Lower The Bit Into The Work Piece Until The Drill Bit Has Cut About 1/4” In To The Wok Piece 3.
If Steel Is To Be Drilled Use The Lowest Speed And Reduce Feed Pressure When drilling by hand use a drill bit that is has a bond that is one (1) class softer than you would normally use with a Rig Mounted drill. III. COMPONENT DESCRIPTION A.
IV. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List part number and serial number of part not the item number. 3. Wherever alternate parts are shown due to product improvement, inspect the part you have and provide additional description as necessary. 4. Specify mode of shipping desired, such as, parcel post, truck, U.P.S., best way, etc.
B.
C. HHD323 Parts Listing Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16-1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 DESCRIPTION GEAR CASE HHD323 SPINDLE HHD323 OIL SEAL 32D 22d DOUBLE LIP SEAL (7SS) HANDLE COLLAR HHD323 HANDLE AND ATTACHMENT BAR HHD323 BEARING RADIAL 6003LLU D35 d17 BEARING RADIAL 6003ZZ D35 d17 INTERNAL C-CLIP M35 EXTERNAL C-CLIP M17 EXTERNAL C-CLIP M9 PLATE HHD323 PLATE FRICTION HHD323 METAL COLLAR HHD323 GEAR FIRST HHD323 WASHER CONICAL D28 d12.
C. HHD323 Parts Listing Item 38 39 40 41 42 43 44 45 46 47 48 49 50 51 51-1 52 53 54 55 56 57 58 59 60 61 61-1 62 Optional Optional Optional Optional Optional Optional DESCRIPTION WASHER M5 DIN125 FLAT ARM BASE TELESCOPIC HHD323 SCR 5/32”-16 X 5/8" SELF TAPPING PHILLIPS HEAD RUBBER COVER HHD323 ARM TELESCOPIC HHD323 RUBBER SHOULDER PAD HHD323 SCR M3.5 X10 SELF TAP PHILLIPS DIN7981 SPRING SHOULDER STOCK HHD323 LOCK RELEASE LEVER HHD323 SCR M6 X 35 1.0 DIN912 SHCS NUT M6 1.0 DIN934 HEX SCR M6 x 25 1.
NOTES:
Saint-Gobain Abrasives 2770 West Washington Stephenville, TX 76401 Phone: 800-554-8003 Fax: 800-443-1092
