Installation Guide

ManualsBrandsClosetMaid ManualsShelves & Shelf BracketsShelfTrack 48 in. x 1in. White Standard

SHELFTRACK

INSTALLATION TIPS

1. USE THE CORRECT HARDWARE

Select the hardware that is right for your wall type:

2. HANG TRACK LOCATION

Track can be installed at any height. However, for maximum

adjustability and strongest installation, install track ush to ceiling

and screw into wood header behind wallboard. Stud installation is

recommended whenever possible for the strongest installation.

3. DETERMINE LENGTH AND SPACING OF STANDARDS

Standards are available in several lengths, depending on the number

of shelves you want and the spacing between the shelves. The closer

the standards are placed together, the stronger the installation.

Standards should be spaced no more than 24 in. apart, and no more

than 4 in. from the end of the shelf.

4. SECURING STANDARDS

Each standard must be secured to the wall with one screw at the

closest hole to the center of the standards. When using toggle bolts,

remove toggle, put bolt through standard and re-attach toggle to bolt

before placing standard on track.

5. ATTACHING BRACKETS

Attach brackets at desired shelf height.

NOTE: Always match bracket size to shelving depth except when using

Shelf & Rod shelving. Always use 12 in. brackets for this type of shelving.

When installing 16 in. SuperSlide

with Closet Rod & Support always use 12

in. brackets.

6. CUTTING SHELVING, CLOSET RODS, AND HANG TRACKS

Wire shelving can be cut using a bolt cutter or hacksaw. Closet rods can

be cut using a pipe cutter (recommended) or a hacksaw. Hang tracks

can be cut with a hacksaw.

7. CORNERS

When two shelves come together in a corner, use a corner shelf support

to connect them. Use a corner closet rod to allow clothes to slide

uninterrupted around corners.

Note: SuperSlide

Closet rod supports should be placed where closet rods join.

8. END CAPS

Add caps to every exposed wire on both ends of each shelf and to

the ends of closet rods. End caps protect you, your clothing and the

shelving materials.

with

A D

B E

C F

Hang Track

Standard

Bracket

Closet Rod

Closet Rod Support

Closet Rod Cap

Shelf End Cap

Choose Your Hardware

Drywall

Drill 1/2 in. holes and

secure to the wall with

toggle bolts.

Studs

Secure to the wall

with #12 x 2 in. pan

head screws at stud

locations.

Concrete

Drill 1/4 in. holes.

insert #12 wall

anchors and secure to

the wall with #12 x 2

in. pan head screws.

24 IN. MAXIMUM

24in.

61cm

ClosetMaid Superslide

shelf system is manufactured by ClosetMaidLLC., Orlando, Florida. Manufacturer reserves the right to change specications without notice.

Summary of content (2 pages)

PAGE 1
A 24in. 61cm B G C E F D with Choose Your Hardware SHELFTRACK INSTALLATION TIPS A Hang Track D Closet Rod B Standard E Closet Rod Support C Bracket F Closet Rod Cap G Shelf End Cap ® 1. USE THE CORRECT HARDWARE 4. SECURING STANDARDS Each standard must be secured to the wall with one screw at the Select the hardware that is right for your wall type: closest hole to the center of the standards.
PAGE 2
12 in. 30,5 cm C B G A FIXED MOUNT F D E with Choose Your Hardware A Support Bracket D Closet Rod B Side Wall Bracket E Closet Rod Support C Wall Clip F Closet Rod Cap G Shelf End Cap 4. CORNERS FIXED MOUNT INSTALLATION TIPS 1. SHELF INSTALLATION There are three ways to install a shelf: Wall-to-Wall, Wall-to-Open, Open-to-Open. Shelves are supported by wall clips and support brackets or support poles. When a shelf is attached to a side wall, a wall bracket is also used.