INSTALLATION GUIDE – GUÍA DE INSTALACIÓN 6' CP5077361 8' 10' 1 NOVEMBER 2019
Size: 8.5”X11” Front Get fast support at 1-866-264-1964 or Support@closetsbyliberty.com Thank you for your recent purchase. If you’ve had a positive buying experience, we would be grateful if you would leave us a positive product review. If you are not entirely delighted with your overall experience, please call us at 1-866-264-1964 so we can discuss any issues you may have. STOP DO NOT RETURN TO THE STORE.
Size: 8.5”X11” Back Obtenga soporte rápido llamando al 1-866-264-1964 o en Support@closetsbyliberty.com Gracias por su compra reciente. Si su experiencia de compra ha sido positiva, le agradeceremos que nos deje una reseña de producto positiva. Si su experiencia general no ha sido completamente satisfactoria, le rogamos nos llame al 1-866-264-1964 para que hablemos sobre cualquier problema que pueda tener. ALTO No devuelva el producto a la tienda.
MEASURE YOUR SPACE - 6 ft – MIDA SU ESPACIO: 6 ft (1.8 m) H W D Outside Width (W) Ancho exterior (W) 3 Towers 3 torres 68-7/8" 68-7/8" Height (H) = 83-1/2" Depth (D) = 16-3/4" Altura (H) = 83-1/2" (2.12 m) Profundidad (D) = 16-3/4" (42.5 cm) Allow for 32" for depth measurement when selecting drawer locations so that the drawer can be fully opened. Deje 32" (81.28 cm) para medir la profundidad al seleccionar la ubicación de los cajones de manera que puedan abrirse completamente.
MEASURE YOUR SPACE - 8 ft – MIDA SU ESPACIO: 8 ft (2.4 m) H W Outside Width (W) D Ancho exterior (W) 4 Towers 2 Towers + 48" Shelf 4 torres 4 torres 2 torres + estante de 48" (1.2 m) 91-5/16" 94-7/16" 91-5/16" 94-7/16" Height (H) = 83-1/2" Depth (D) = 16-3/4" Altura (H) = 83-1/2" (2.12 m) Profundidad (D) = 16-3/4" (42.5 cm) Allow for 32" for depth measurement when selecting drawer locations so that the drawer can be fully opened. Deje 32” (81.
MEASURE YOUR SPACE - 10 ft – MIDA SU ESPACIO: 10 ft (3.05 m) H W Outside Width (W) Ancho exterior (W) 5 Towers 5 torres 113-3/4" 113-3/4" Height (H) = 83-1/2" Depth (D) = 16-3/4" D Altura (H) = 83-1/2" (2.12 m) Profundidad (D) = 16-3/4" (42.5 cm) Allow for 32" for depth measurement when selecting drawer locations so that the drawer can be fully opened. Deje 32" (81.28 cm) para medir la profundidad al seleccionar la ubicación de los cajones de manera que puedan abrirse completamente.
REQUIRED TOOLS – HERRAMIENTAS REQUERIDAS TOWER HARDWARE – ADITAMENTOS PARA LA TORRE RR AA BB Top Frame Screw Tornillo de armazón superior Leveling Foot Pata de nivelado Front Frame Screw Tornillo de armazón frontal Stabilizer Bar Screw Anti-Tip Bracket Screw Tornillo de barra Tornillo de soporte estabilizadora Drywall Anchors antivuelco Anclajes para tablero de pared CC EE 7 FF
TOWER PARTS IDENTIFICATION – IDENTIFICACIÓN DE LAS PARTES DE LA TORRE A* Cabecera del armazón (Parte superior del armazón) Frame Header (Top of Frame) E Top Shelf Estante superior H Front Stabilizer Cover Cubierta del estabilizador frontal F Slide On Shelf Estante deslizante B* Long Vertical Sides lados verticales largos I Rear Stabilizer Cover Cubierta del estabilizador trasero J Top Rear Stabilizer Bar Barra estabilizadora de la parte superior trasera K Stabilizer Bar Barra estabilizadora L C*
TOWER ASSEMBLY (ALL CONFIGURATIONS) ENSAMBLAJE DE LA TORRE (TODAS LAS CONFIGURACIONES) Before beginning, identify components and read all instructions. Antes de comenzar, identifique los componentes y lea todas las instrucciones. 1 BB Top of assembly Header (A) has 4 holes for mounting hanging bars 4 1 Parte superior del conjunto La cabecera (A) tiene 4 agujeros para montar las barras de colgar B C 2 1 B A 2 3 AA Long vertical sides (B) come pre-assembled with couplers in place.
2 Top rear of assembly 1 Parte superior trasera del conjunto 2 J 1 WARNING - ADVERTENCIA Stabilizer Bars: Install with slots facing upwards and the closed side of the bar facing inwards. Barras estabilizadoras: Instálelas con las ranuras mirando hacia arriba y el lado cerrado de la barra mirando hacia adentro. K 3 3 CC Install a top stabilizer bar (K) and rear stabilizer bar (J) to one side of the frame. Secure with screws (CC).
4 CC 1 2 1 1 Install second half of the frame to the footer and header stabilizer bars. Secure with screws (CC). Instale la segunda mitad del armazón en las barras estabilizadoras del pie y la cabecera. Asegúrela con los tornillos (CC). 5 6 A WARNING - ADVERTENCIA Tower may be unstable until securely attached to the wall with supplied fasteners. A La torre puede quedar inestable hasta que se fije a la pared con los sujetadores que se suministran.
Tower Only Configurations • Complete steps 7-18 (for all towers) Configuraciones de solo la torre • Complete los pasos 7 al 18 (todas las torres) 48" Spannable Shelf Configurations • Repeat steps 1-5 for remaining tower • Complete steps 11-18 for one tower only • Proceed to 48" Spannable Shelf Installation on page 17 48" Configuraciones del estante de doble ancho • Repita los pasos 1 al 5 para la torre que queda • Complete los pasos 11 al 18 para una sola torre • Proceda a la instalación del estante de
7 BB 4 Top of assembly Header (A) has 4 holes for mounting hanging bars 1 Parte superior del conjunto La cabecera (A) tiene 4 agujeros para montar las barras de colgar B C 2 1 B A 2 3 AA Long vertical sides (B) come pre-assembled with couplers in place. Assemble two long vertical sides (B) with the horizontal top (A) and bottom (C) headers. Secure the top with screws (AA) and the bottom with levelers (BB). The first three steps of assembly are completed with the frame laying on its side.
8 WARNING - ADVERTENCIA Stabilizer Bars: Install with slots facing upwards and the closed side of the bar facing inwards. Barras estabilizadoras: Instálelas con las ranuras mirando hacia arriba y el lado cerrado de la barra mirando hacia adentro. 2 J 1 Top of assembly Parte superior del conjunto K 3 1 3 CC Install a top stabilizer bar (K) and rear stabilizer bar (J) to one side of the frame. Secure with screws (CC). Note: Rear stabilizer bar bracket (J) screw opening must face top of unit.
CC 2 10 1 1 1 A 1 RR 1 After standing frame upright with the opening facing toward you, install frame to existing assembled frame. Secure with screws (RR). Fasten 2 of the small head screws (RR) at location marked (A). These screws can be installed from either side. Repeat for remaining towers. Después de poner de pie el armazón con la apertura mirando hacia usted, instale el armazón al armazón ensamblado existente. Asegure la estructura con los tornillos (RR).
11 12 1 F L 1 L 1 2 2 Install a shelf bracket (L) (there are no left or right brackets) into side frame channels at a 45˚ angle. Drop shelf (F) in place on brackets (L) with the track opening at the rear of the shelf. Once inserted into side frame slots, twist bracket into place until it 'clicks'. Repeat on opposite side. Slide the shelf towards the rear until track clips (on underside of shelf) 'click' into place. A small amount of force may be required.
14 Locate and mark any wall studs behind the rear top stabilizer. If no studs are present, identify suitable locations for drywall anchors. They should be spaced as evenly as possible. Slide the anti-tip brackets to slot corresponding with the stud location or drywall anchor. Mark wall location of the screw opening with a pencil. Lift and slide brackets to the side to allow access to the marked wall locations.
16 I H *SNAP* *SNAP* Install front (H) and rear (I) decorative covers by hooking each cover over top of stabilizer bar, then rotating down and snapping into place. Repeat for the remaining front and rear cover. Instale los cubiertas decorativos frontales (H) y traseros (I) enganchando cada uno encima de la parte superior de la barra estabilizadora, girándolos después hacia abajo y encajándolos en su lugar. Repita para los cubiertas frontal y trasero que quedan.
48" SHELF PARTS AND HARDWARE – PIEZAS Y ADITAMENTOS DEL ESTANTE DE 48" (1.2 m) D 48" Shelf Estante de 48" (1.2 m) G 48" Shelf Brackets Soporte del estante de 48" (1.2 m) Z DD Shelf Bracket Screw Tornillo de cubierta del estante NN 48" Shelf Cover Cubierta del estante de 48" (1.2 m) Shelf Cover Screw Tornillo de soporte del estante 48" SHELF INSTALLATION – INSTALACIÓN DEL ESTANTE DE 48" (1.
2 D Place inner base of second tower assembly into position at other end of 48" shelf (D). Coloque la base interior del conjunto de la segunda torre en su posición en el otro extremo del estante de 48" (D). 4 3 1 F 1 1 L L 2 2 Install a shelf bracket (L) (there are no left or right brackets) into side frame channels at a 45˚ angle. Once inserted into side frame slots, twist bracket into place until it 'clicks'. Repeat on opposite side.
5 Check that tower is level. Turn leveling feet to adjust as necessary Verifique que la torre esté nivelada en todas las direcciones. Gire las patas de nivelado para ajustarlas segun sea necesario. 1 6 WARNING - ADVERTENCIA Anti-tip brackets MUST be fully seated in chosen slots of top stabilizer. Los soportes antivuelco DEBEN estar asentados por completo en las ranuras elegidas del estabilizador superior. WARNING - ADVERTENCIA Brackets should be as evenly spaced as is possible.
If mounting on a stud: Drill a 1/8" pilot at marked point with a drill. Slide the brackets back into final positions. Ensure they are seated fully. Use screws (FF) to secure brackets to the wall. If using a wall anchor: Install anchors (EE) into wall at marked point with a drill with a Phillips head. Slide the brackets back into final position. Ensure they are seated fully. Use screws (FF) to secure brackets to wall. The Tower should now be locked to the wall and unable to move.
Left Tower Assembly Right Tower Assembly Conjunto de torre izquierda Conjunto de torre derecha 1 1 9 G DD 2 Install a 48" shelf bracket (G) to the upper inside of both tower assemblies. Secure brackets with four screws (DD) per bracket. Note: For 48” middle shelf kit substitute 2 shelf brackets (L) Instale un soporte de estante de 48" (G) en la parte interior de arriba de los dos conjuntos de torres. Fije los soportes con cuatro tornillos (DD) por soporte.
11 2 2 1 D G 1 Drop 48" shelf (D) in place on brackets (G) with the track opening at the rear of the shelf. Slide the shelf towards the rear until track clips (on underside of shelf) 'click' into place. A small amount of force may be required. Deje que el estante de 48" (D) caiga en su lugar sobre los soportes (G) con la apertura del carril en la parte trasera del estante.
13 E E Place top shelf (E) on top of the tower and drop in place. The shelf should sit securely so that the top surface is level with the frame. Repeat for all towers. Coloque el estante superior (E) encima de la torre y déjelo caer en su lugar. El estante debe asentarse de forma segura de manera que la superficie superior esté a nivel con el armazón. Repetir para todas las torres.
OPTIONAL ACCESSORIES (IF INCLUDED) ACCESORIOS OPCIONALES (SI SE INCLUYEN) HARDWARE – DRAWERS AND EXTRA SHELVES ADITAMENTOS: CAJONES Y ESTANTES ADICIONALES KK HH II JJ GG PARTS IDENTIFICATION – DRAWERS AND EXTRA SHELVES IDENTIFICACIÓN DE LAS PIEZAS: CAJONES Y ESTANTES ADICIONALES M O N Left side Lado izquierdo V Rear Parte de atrás Bottom Parte inferior Left Drawer Slide Guía del cajón izquierdo Slide Connector Conector de deslizamiento Pull Manija P Q Front • Frente Right side • Lado derec
Before beginning installation, identify components and read all instructions. Antes de comenzar la instalación, identifique los componentes y lea todas las instrucciones. 2 1 Backside of Drawer S T Parte trasera del cajón GG 1 JJ II U R GG P 2 Install cam screws (GG) and dowels (II) into the backside of larger front drawer panel (T). Slide large rear drawer panel (S) into slots of larger side panels (U, R). Install cam screws (GG) into the back of the smaller front drawer panel (P).
4 Install cams (HH) into larger side drawer panels (R, U). R Repeat for all remaining larger drawer side panels and smaller drawer side panels (M, Q). S Note: All CAM arrowheads must face toward the front drawer. Instale las levas (HH) en los paneles laterales de los cajones grandes (R, U). Repita para todos los paneles laterales que quedan de los cajones grandes y pequeños (M, Q). U N Nota: Todas las puntas de flecha de las levas deben mirar hacia el frente del cajón.
7 Turn the drawer over and find the 3 pilot holes located on the left and right of the rear of the drawer front. 1 Arrange the gray plastic slide connectors so that their attachment holes align with the pilot holes. Using the 6 screws (KK) provided, attach the left and right plastic slide connectors to the underside of the front of the drawer as shown. 1 Dele vuelta al cajón y encuentre los 3 agujeros piloto ubicados a la izquierda y la derecha de la parte trasera del frente del cajón.
9 10 Slide completed drawer into place on brackets until it 'clicks'. Complete remaining product drawers by repeating steps 7-9. Deslice el cajón terminado en su lugar sobre los soportes hasta que haga “clic”. Note: Install each remaining drawer immediately above previously installed drawer. Install the drawer slide brackets in the next visible slot. Complete los demás cajones del producto repitiendo los pasos 7 al 9.
11 12 1 F 1 1 L L 2 2 Drop shelf (F) in place on brackets (L) and then slide shelf towards rear until track clips (on underside of shelf) 'click' in place. A small amount of force may be required. WARNING - ADVERTENCIA DO NOT install drawers above chest height NO instale cajones por encima de la altura del pecho. Install shelf bracket (L) (there are no left or right brackets) into side frame channels at a 45˚ angle. Repeat steps 11 and 12 for remaining shelf.
CLOTHES ROD – BARRA PARA ROPA HARDWARE AND PARTS IDENTIFICATION IDENTIFICACIÓN DE PIEZAS Y ADITAMENTOS X Y MM LL Clothes rod can be installed 2 ways: 1. Under the top shelf 2. Attached to shelf brackets and moved as needed La barra para ropa se puede instalar de 2 maneras: 1. Debajo del estante superior 2.
Clothes Rod Installation – Lower Shelf Instalación de la barra para ropa - Estante inferior 1 2 L 1 1 L MM X X 2 2 To install clothes rod below a shelf, use two screws (MM) to attach the clothes rod bracket (X) onto a shelf bracket (L) using the front set of holes. Repeat for the second bracket. Install a shelf bracket with clothes rod bracket (L, X) into side frame channels at a 45˚ angle. Once inserted into side frame slots, twist bracket into place until it 'clicks'. Repeat on opposite side.
REMOVING ACCESSORIES RETIRO DE ACCESORIOS Shelf and Shelf Bracket Removal Retiro del estante y del soporte del estante 1 2 F 2 L L 2 1 3 3 1 To release shelf (F), press both clips on the front underside of shelf. To remove shelf bracket (L), lift up on the front of bracket to 45˚ to release it from side frame slots. Slide shelf (F) forward and then lift off of shelf brackets (L) to remove. Repeat on opposite side.
Clothes Rod Removal – Upper Shelf Retiro de la barra para ropa - Estante superior 2 1 L Y 2 X 1 To remove shelf bracket (L), lift up the front of bracket to about 45˚ to release it from side frame slots. Repeat on opposite side. To remove clothes rod (Y), lift rod up off the bracket and bracket pegs (X). Para retirar la barra para ropa (Y), levante la barra del soporte y de los estribos del soporte (X).
Clothes Rod Removal – Top Panel – Retiro de la barra para ropa - Panel superior 2 1 LL Y 2 X X 1 To remove clothes rod (Y), lift rod up off the bracket and bracket pegs (X). Para retirar la barra para ropa (Y), levante la barra del soporte y de los estribos del soporte (X). To remove clothes rod bracket (X) from top panel, loosen and remove clothes rod bracket screw (LL) and clothes bracket (X). Repeat on opposite side.
