INSTRUCTION MANUAL 9.2” TFT LCD COLOR MONITORING SYSTEM With 2 Indoor/Outdoor Color Cameras MODEL: LCD0935 Ver. 061109, 011510 Copyright © 2009 Wisecomm. All Rights Reserved.
1. IMPORTANT SAFETY PRECAUTIONS ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ To prevent fire or shock hazard, do not expose the monitor to rain or moisture. To avoid electrical shock, do not open the case of this product. Operate this product using only the supplied power supply . Do not overload electrical outlets or extension cords, this can result in fire or electric shock. Keep this product away from strong magnetic fields. Do not expose this product in direct sunlight or strong reflected rays.
1. This light is lit in blue when the AC power supply is properly plugged to DC jack (refer to #9). 2 -Select the CH1 camera by pressing this button in the manual mode or automatic sequential mode. -Press Down (▼) button to navigate the submenu. 3. -Select the CH2 camera by pressing this button in the manual mode or automatic sequential mode. -Press Up (▲) button to navigate the submenu. 4. -Decrease audio level by pressing this button. -Press Left (◄) button to select values. 5.
12. Audio input (RCA jack) Audio input port for VCR playing 13. Audio output (RCA jack) Audio output port for recording. 14. Video input (BNC) Video input port for VCR playing 15. Video output (BNC) Video output port for recording. Note: -Audio on the provided cameras is available. 3.2 CAMERA 1. Lens 3.6mm fixed Lens. 2. Infrared LEDs 30 Infrared LEDs let you see objects in the darkness. 3. CDS sensor Automatically turns the Infrared LEDs on at night. 4. Sunshield 5. Mounting bracket 6.
4. INSTALLATION 4.1 Installation of Mounting Bracket for TFT LCD Monitor 1. Turn the tightening knob① counter-clockwise to disassemble the swivel. 2. Place the fixed ring② into the swivel as shown illustration above and turn the tightening knob① clockwise to secure the swivel. Pay attention not to miss the spring③. 3. Loosen the locking knob and set the proper angle of square metal④ on the top of the swivel.
4. Place the square metal④ on the top of the mounting bracket into the metal hole ⑤ on the rear of the monitor as shown illustration above, then secure the monitor using the locking ring ⑥. 5. Turn the tightening knob① clockwise to secure the swivel after setting the desired angle of monitor to display. It can be used for wall-mount or ceiling-mount application depending on the setting. 4.
1. Attach the mounting bracket base ① to the wall or ceiling, wherever you want to install the camera. Locate a wall stud or ceiling joist and secure the bracket base using the supplied screws. 2. Lock the mounting bracket with the locking ring②. 3. Turn the pivot locking screw③ with the provided hex-head wrench counterclockwise to set the desired angle of camera toward objects and turn it clockwise to secure.
- All the menus will automatically disappear if you don’t change values within 10 seconds. - The remote controller may not control all the functions on the system. In case of this, please use the buttons on the front panel. 6.1 Video Enhancement ( ) - Press the MENU button on the front panel to setup the menus. - Select the VIDEO INHANCEMENT icon in the MAIN MENU by using the ► and the ◄ buttons. - Choose an item with the ▲and the ▼buttons and select the values with the ► and the ◄ buttons.
- Choose one among 15, 30, 45 and 60 to turn the power off automatically after the selected time in minute. Sharp: - Adjust the sharpness of images. Panel-LR: - You can view the mirror images or normal images by selecting. Panel-UD: - You can view the reverse images or normal images by selecting. AUTO-SWITCH - Select the dwell time for the automatic sequential mode. VCR - Select VCR in the SYSTEM MENU and press ► or the ◄ buttons to set the system in playback mode. To return to live mode, press CH1 or CH2.
Minimum illumination IR LED S/N ratio Gamma characteristics Video output Microphone Exposure Time Range Lens Current consumption Power supply Housing material Operational temperature Dimensions Weight 0 Lux (LED on), 0.1 Lux @F1.2 (LED off) 30pcs, Wave Length: 850nm More than 48db (AGC off) 0.45 1.0Vp-p Composite @75 ohms Waterproof C-Mic 1/60s ~ 20µs 3.6mm fixed lens 400 mA Max @LED on DC 12V (Regulated: not included) Die cast aluminum alloy -10°C to 50°C RH95% Max 55Ø x 95(L) mm 1.1 Lbs 8.
▪ Please pack the system carefully and securely using the original packing materials, and send it prepaid and insured to: 13073 E. 166th St, Cerritos, CA 90703. ▪ Please include a check for $20.00 to cover the cost of return postage and handling. If the system is returned within the warranty period, please include a proof of purchase. If the system is out of warranty, you will receive an estimate of the repair cost for your approval before repair work will be started.
