Owner manual

ManualsBrandsCM-ET ManualsHoistSeries 603

SERIES 602/603

Manually Lever Operated Chain Hoist

Maximum Capacity:

Series 602: 550 Pounds (250 Kg.)

Series 603: 1100 Pounds (500 Kg.)

FORWARD THIS MANUAL TO OPERATOR:

If not properly installed, operated and maintained, the use

of all mechanical equipment presents the possibility of

personal injury or property damage. Before hoist use, all

persons should read this manual thoroughly. For safe, de-

pendable and economical performance, follow all instruc-

tions and recommendations contained herein. It is also

important to retain this manual for current and future use.

COLUMBUS McKINNON CORPORATION

140 JOHN JAMES AUDUBON PARKWAY

AMHERST, NEW YORK 14228-1197

02805 MANUAL NO. 602/603-A

LEVER OPERATED CHAIN HOISTS

Printed in China

Operating, Maintenance

& Parts Manual

Model Number

Serial Number

Purchase Date

Series 602 Series 603

Summary of content (8 pages)

PAGE 1
LEVER OPERATED CHAIN HOISTS 02805 Operating, Maintenance & Parts Manual SERIES 602/603 Manually Lever Operated Chain Hoist Maximum Capacity: Series 602: 550 Pounds (250 Kg.) Series 603: 1100 Pounds (500 Kg.) Series 602 Series 603 FORWARD THIS MANUAL TO OPERATOR: If not properly installed, operated and maintained, the use of all mechanical equipment presents the possibility of personal injury or property damage. Before hoist use, all persons should read this manual thoroughly.
PAGE 2
INSTALLATION 1. Read and understand the safety precautions on page 7 of this manual. 2. Estimate the load that is to be lifted or moved and make sure it does not exceed the hoist’s rated capacity (550 lbs. / 250 Kg. for the Series 602 and 1100 lbs. / 500 Kg. for the Series 603). 3. Make sure that the support to which the upper hook is attached is strong enough to hold several times the weight of the load.
PAGE 3
FREE CHAINING In this mode, the load can be pulled through the hoist in either direction by hand for quick attachment to the load. To set the hoist to free chaining mode: 1. With no load on the hoist, move the directional lever to the center (neutral) position. 2. *Pull the load chain, in either direction, to its desired length so that the lower hook can be attached to the load. Note that the chain must feed into the hoist freely. If it does not, check for twisted chain.
PAGE 4
If directional lever is forced out of engagement with a load applied, load will be released. TO AVOID INJURY: With a load applied to the hoist, do not force the directional lever into the center (neutral) position. LOCKED BRAKE If a hoist under load is suddenly relieved of the load by removing the load from the hoist by some other means, the brake will remain locked. The brake could also lock if the lower hook block is run tightly against the frame.
PAGE 5
FREQUENT & PERIODIC INSPECTION CHART FREQUENCY ITEM LABELING & TAGS OPERATION HOOK ASSEMBLIES CHAIN BRAKE DISC HOIST HEAD EVERY 6 DAILY MONTHS (FREQUENT)* (PERIODIC) WHAT TO CHECK INSPECTION METHOD X X Nameplate, capacity label warning labels & free chaining tag Visually X X General Operation Lift & lower a light load ACCEPTANCE LEVEL These items must be legible and securely fastened to the hoist. Replace if necessary. 1. Chain must feed into and out of the hoist freely. 2.
PAGE 6
SERIES 602/603 LEVER HOIST PARTS LIST PART NUMBER DESCRIPTION 602 CHAIN STOP ASSEMBLY 603 00230260 LOAD CHAIN (PER FOOT CODE) 02100004 02100009 HOOK LATCH KITS (2 INCLUDED) 00230168 00400449 CM HOISTS PARTS AND SERVICES ARE AVAILABLE IN THE UNITED STATES AND IN CANADA As a CM hoist user you are assured of reliable repair and parts services through a network of Master Parts Depots and Service Centers that are strategically located in the United States and Canada.
PAGE 7
SAFETY PRECAUTIONS Each Series 602/603 Manually Operated Lever Hoist is built in accordance with the specifications contained herein and at the time of manufacture complies with our interpretation of applicable sections of *ASME B30.21, *ANSI/ASME HST-3M and the Occupational Safety and Health Act-1970. The safety laws for elevators and for dumbwaiters specify construction details that are not incorporated in CM industrial hoists.
PAGE 8
WARRANTY Every hoist is thoroughly inspected and performance tested prior to shipment from the factory. If any properly installed, maintained and operated hoist as outlined in the applicable accompanying CM manual develops a performance problem due to defective materials or workmanship as verified by CM, repair or replacement of the hoist will be made to the original purchaser without charge and the hoist will be returned, transportation prepaid.